Craig LH-X15 User manual

| Oer'sManual
且归日却因UA士北M昢画咖l咄哗
Model: LH-X15
Remote Control Drone

FCC INFORMATION:
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide residential protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception. which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
 Reorient or relocate the receiving antenna.
 Increase the separation between the equipment and receiver.
 Connect the equipment into an outlet on the circuit different from that to which the receiver is
connected.
 Consult the dealer or an experienced radio/TV technician for help.
FCC WARNING:
The equipment may generate or use radio frequency energy. Changes or modifications to this
equipment may cause harmful interference unless the modifications are expressly approved in the
instruction manual. Modifications not authorized by the manufacturer may void user’s authority to
operate this device.
GENERAL WARNINGS:
1. Important Instructions:
 This product is suitable for 14 years old and above. Please read the instruction manual
before you play with this product.
2. Make sure the unit always within the Radio Frequency control range. Otherwise, the
unit will out of control and may crash.
3. Safety Instructions:
 Keep away from the objects and crowds.
 The unit is flying at high speed; keep it away from crowds, buildings, high voltage
wires, etc.
 Do not operate this unit in bad weather.
 Keep away from water and rain.
 The unit has electronic and mechanical parts which may be damaged by water and
rain.
 Keep away from the working unit.
 The blades are turning in high speed, always keep away from it.
1
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1)This device may not cause harmful interference. and (2) this device must accept any interference
received, including interference that may cause undesired operation.

LOCATION OF CONTROLS:
Main Unit:
1
1
4
5
2.
3346
7 8
1.
Blades
2. Camera
3. Blade’s Protectors
4. Landing Gears
5.
6.
7.
8.
9.
Battery USB Cable Charging Socket
10.
Micro SD Card Slot
Turn on/Turn off button
Battery Door/Battery Compartment
Battery Connection Cable/Jack
Li-ion battery
910
Rechargeable Battery
2

REMOTE CONTROL:
16
15
14
12
10
11
9
7
6
5
2
4
3
1
8
13
Serial
Number Function keys Function / Effect
1
2
3
4
9
6
7
8
11
15
12
13
14
16
Power On/Off
Power On Indicator
Left Joystick
Right Joystick
Up/down/turn left/turn right
Forward/backward/left/right
10
5
Photo Capture /
Video Recording button Short press is Photo Capture, the lights will flash once/Long press is video Recording,
the drone lighs will flash twice, long press 3 sec to cancel,the drone lighs will flash twice.
Flip Button The Drone will flip over when press this flip button and then the Right Joystick per direction.
Speed Selection button Low/Medium/High speed
Headless/One Key
Return button Short press is headless mode/long press is One Key Return mode, long press 3 sec to cancel
One Key start/One Key Take Off/
One Key Landing Button
One Key Emergency Stop
Left Fly Trimmer
Right Fly Trimmer
Backward Fly Trimmer
Forward Fly Trimmer
Battery Door(On the rear)
Security Screw of Battery Door
Turn On/Off the remote control
The drone will stop and fell down immediately when you press this button .
If the drone fly backward without any operation, press the Forward Fly trimmer
button correspondingly, it can make the drone fly stable.
If the drone fly forward without any operation, press the Backward Fly trimmer
button correspondingly, it can make the drone fly stable.
If the drone fly right side without any operation, press the Left Fly trimmer
button correspondingly, it can make the drone fly stable.
If the drone fly left side without any operation, press the Right Fly trimmer
button correspondingly, it can make the drone fly stable.
Close the door on the rear when use.
Use screw driver to tighten the security screw of battery door.
Press this button first time, this drone will start . press second time, the drone will take off.
press third time, the drone will landing.
The power on indicator will be stable when working normal, but it will flash quickly when
low power of remote control.
3

PREPARATIONS:
Battery Recharging:
The unit has a DC 3.7V Li-ion rechargeable battery. Recharge it before first time use or when it is
low poweras follows:
1. Connect the USB charging cable to the battery charging socket on the drone body.
2. Connect the USB charging cable to
Personal Computer or AC adaptor (Computer and
not included)
3. Charging will automatically start. The Red Indicator inside
USB Plug will turn on when charging,
When finished charging, the indicator will turn off.
4
AC adaptor
,it is suggested the AC adaptor not above 1A.
Note:When first time use, please use supplied screw driver to open the battery cover, connect the battery
and the drone, then closed it with screw.(only for first time used,no need to open battery cover when
follow use)
Rechargeable Battery

BATTERY INSTALLATION:
Main Unit:
Notes:
battery will last longer if you canfollowing these simple guidelines :
A. Before first time use, charge it approximately 60 mins(Computer or 0.5AAC charger
B. Recharge and store the unit within the temperature range of 5°C~35°C (40°F~95°F).
C. Do not charge longer than 12 hours. Excessive charging or running the unit until battery fully
drains will damage battery. Battery life will be extended if you keep the battery fully charged.
D. Battery life naturally shortens slowly over time.
5
The
approximately 45-60mins, 1AAC charger approximately 30-40mins) until the battery
is fulled charged.
1. Use screw driver to open the the battery door.
2. Put the battery into the battery compartment and connect the drone and battery
3. Close the door and fix it with screw.
Rechargeable Battery
Rechargeable Battery

Remote Controller
9. Unlock (start motors)
Take-off
Land
11. Emergency Stop
1. Speed
Low speed: 1 beep
Mid speed: 2 beeps
High speed: 3 beeps
13. Power on/
3. Photo/Video
Photo: short press
Video: long press
5. Throttle
Ascend/Descend/
Turn left/Turn right
7. Headless/Return
Headless: short press
Return: long press
Remote Control:
1. Looser the screw on the Battery Door by a screwdriver
.
2.
3. Install or replace the batteries by three (3) AAA size batteries (not included) into the battery
compartment(Alkaline batteries are recommend forlongest playing time).
4. Closed the battery door.
5. Tighten the screw on the door.
Battery Precautions:
Follow these precautions when using a battery in this device:
1. Using only the size and type of battery specified.
2. Be sure to follow the correct polarity when installing the battery as indicated in the battery
compartment. A reversed battery may cause damage to device.
3. Do not mix different types of batteries together (e.g. Carbon-zinc, Alkaline) or old batteries
with fresh ones.
4. If the batteries in the device are consumed or the device is not to be used for a long period of
time, remove the batteries to prevent damage or injury from possible battery leakage.
5. Do not try to recharge the battery after fully charged, it can overheat and rupture. (Follow
battery manufacturer's instructions.)
6. Do not dispose of battery in fire. Battery may explodes or leak.
7. Clean the battery contacts and also those of the device prior to battery installation.
6
3 x 1.5V AAA
batteries
Open the battery cover.
Remote Controller
9. Unlock (start motors)
Take-off
Land
11. Emergency Stop
7. Headless/Return
Headless: short press
Return: long press
Remote Controller
9. Unlock (start motors)
1. Emergency Stop
7. Headless/Return
Remote Controller
9. Unlock (start motors)
1. Emergency Stop
7. Headless/Return

Remote Controller
9. Unlock (start motors)
1. Emergency Stop
7. Headless/Return
Remote Controller
9. Unlock (start motors)
1. Emergency Stop
7. Headless/Return
Remote Controller
9. Unlock (start motors)
1. Emergency Stop
7. Headless/Return
Remote Controller
9. Unlock (start motors)
1. Emergency Stop
2. Flip
(For non-camera version only)
6. Rudder
Forward/Backward/
Leftward/Rightward
4. Forward Trim
8. Backward trim
10. Leftward trim
12. Rightward trim
7. Headless/Return
14. Indicator
MICRO SD CARD INSTALLATION:
The unit is support to take photos/videos then store in a Micro SD Card (not included).
Insert a Micro SD Card into the Micro SD Card Slot with contact fingers face to side as the
illustrated below:
Notes:
A. Insert the class 4 (or up) Micro SD Card (Up to 32GB) into the Micro SD Card Slot
When inserting the storage card, make sure the direction you selected is correct.
Never insert violently to avoid damaging the card or the unit. If it doesn’t work,
please check if the direction is correct.
B. To take out the card, press the card until a “Click” sound is heard then pull out the card.
C. Before insert or replace the storage card, make sure the unit is in powered off mode.
D. When the card is first time use, or it has been used in other device. Format it through the
computer before install to the unit.
(Important: After format, all record in the memory card will be erased. Upload the record to the
computer before format.)
OPERATION
1. Insert the Micro SD Card into the unit as previously instructed.
2. Recharge the supplied rechargeable battery,turn on the drone.
The decorative LED lights on the unit will illuminate and blink.
3. Place the unit on a horizontal place.
4. Install the batteries to the Remote Control as the previous procedures. Press the Power
On/Off Button to turn on the Remote Control. The Power On Indicator will turn on and blink.
7
the
REMINDER : Please operate the drone in spacious indoor or outdoor environment without rain or snow
and wind power should be below 4 grade (gentle breeze), be away from people, animals and obstacle.

5.
B.
Slide the Left Joystick upward again to rise.
C. Slide the Left Joystick downward to reduce the height or landing.
D. To landing and stop flying, slide the Left Joystick downward and hold. The unit will
landing and the Blades will stop turning.
Or, press the “One Key Landing Button”, the drone will landing automatically.
To stop flying emergency, Press the button “One Key Emergency Stop”
The blades will stop
immediately.
E. Slide the Left Joystick to left to turns the unit counterclockwise.
F. Slide the Left Joystick to right to turns the unit clockwise.
G. Slide the Right Joystick upward to fly to forward.
H. Slide the Right Joystick downward to fly to backward.
I. Slide the Right Joystick to left to fly to left.
J. Slide the Right Joystick to right to fly to right.
K. Press the Headless/One Key Return Button once to enter to the Headless mode. The
unit will automatically identify where the front of is. Then slide the Right Joystick upward
to fly the unit to it. Press the Button again to resume normal control.
L. Press and hold the Headless/One Key Return Button to enter to the One Key Return
mode. The unit will fly to the start flying position automatically.
M. During flying,
N. Press the Left /Right Fly Trimmer (Direction and buttons on right) repeatedly to
fine tune the Joystick’s control of Left/Right flying.
O. Press the Forward/Backward Fly Trimmer (Direction and buttons on right)
repeatedly to fine tune the Joystick’s control of Forward/Backward flying.
P. During flying, press the Speed Button (
repeatedly to adjust the speed
as desired.
Q. During flying, the Photo Capture/Video Recording）
short press the Button （
to take photo, the lights will flash one time when take a picture.
R. During flying,
to start video recoring,
S.
Press the Counterclockwise/Clockwise Fly Trimmer (Direction and buttons on
right) repeatedly to fine tune the Joystick’s control of Counterclockwise/Clockwise flying.
T. During flying, slide the Left Joystick Upward/Downward to define the height of unit. Then
release the Left Joystick to stop rising. Slide the Left Joystick Upward/Downward again
to resume normal control.
8
the Photo Capture/Video Recording） long press the Button （
press the Flip button to flip the unit .
Selection
The drone and Remote Control will automatically pairing after both items turn on .
After paired successful, the Lights on the drone and remote control will stop blinking, then:
A. Slide the Left Joystick upward twice to start flying and rising. or press the button
(One key start/One key take off/One key landing),first press is start, second press is one
key take off.
the lights will flash when take a video. Long press again
to stop recording.

6.
off the unit (or take out the battery to recharge), landing it and wait the blades
completely stop turning as instructed earlier. Open the Camera Module/Battery Door then
disconnect the Battery from the Battery Connecting Plug.
7.
Turn off the Remote Control, press the Power On/Off Button to turn off the Remote
Control. The Power Indicator will not light.
BLADE(S) REPLACEMENT:
If any blade was damaged or deformed, replace it by the supplied same color of spare blade with
the supplied screwdriver as illustrated below:
Note: Always replace the damaged blade by the same color of blade. Otherwise, the motion of the
unit will become abnormal.
9
Turn
Gyroscope Reset
Before first flying , or if the drone is not stable flying after crash, or fell down on the
ground, you ahll to reset toe Gyroscope.
1. Pull the Throttle and Rudder down to 45 degree (Bottom Right corner as picture) for
2-3 seconds, the lights on the drone will blinking and you will hear 2 beep ‘Di-Di’, then
let go of the Throttle and Rudder, the lights on the drone will stop blinking.
then gyroscope reset complete.
6. To off the unit (or take out the battery to recharge), landing it and wait the blades
completely stop turning as instructed earlier. Open the Battery Door then
disconnect
the Battery from the Battery Connecting Plug.
7. To turn off the Remote Control, press the Power On/Off Button to turn off the Remote
Control. The Power Indicator will not light.
GYROSCOPE RESET
BLADE(S) REPLACEMENT:
If any blade was damaged or deformed, replace it by the supplied same number(A or B) spare blade with
the supplied screwdriver as illustrated below:
9
Before first flying, or crash, or fell down quickly, or other action which make the drone flying
unstable,you need to reset the build-in Gyroscope as follows:
1. pull the left joystick and right joystick down to 45 degree (Bottom Right corner
as picture) for 2-3 seconds, the lights blinking quickly,and then the lights will stop blinking,
then release the two joystickst. and then gyroscope reset complete.
Note:Always replace the damaged blade by the same letter(A1 or B1) blade,or else, the motion of the
drone will become abnormal or cannot fly up at all(In fact, there are 2A and 2B on the drone, the two
blades(across corner)are same（A1=A2,B1=B2).Do not mix them.
turn
LED light
A
A
B
B

TROUBLE SHOOTING:
SYMPTOM: POSSIBLE CAUSE POSSIBLE SOLUTION
The batteries are drained. Replace by new batteries. Remote Control not work
Batteries wrong installed. Reinstall the batteries as the polarity marking
inside the battery compartment.
The battery had
not connected to the unit
Connect the battery to the unit
per page 5 and 6.
per page 4.
The battery drained. Recharge the built-in battery
per page 4.
The drone not work
The unit had not paired to the
Remote Control.
Pair the unit to the Remote Control
The blade still running after
landing
The unit had not completely
landing and stop running.
Landing and wait the blades stop running as
page 8 point D
Control abnormal
or motion unstable
One (or more than one)
blade(s) deformed or
damaged.
Check and replace the deformed/damaged
blade(s) by new one as page 9.
The unit can not
moving straightly
or auto turning
Reset the built-in Gygo as page 9
Or, fine turn the trimmers as page 8 point N - O
Micro SD Card had
not installed
Install a Micro SD Card (not included) as page 7 Camera not functioning
10
per page 7-9.

General Specification:
Power Source:
Unit:................................. Supplied DC 3.7V, 380mAh (1.406WH) Li-ion rechargeable
battery. Recharge by DC 5V
Remote Control:....................................DC 4.5V,3xAAASize Batteries (Not Included).
Effective range of Radio Control:..........Up to 100 feet in open area
Radio Frequency:................................. 2.4GHz
Sensor of Camera:................................300k Pixels
Capture Modes:
Photo: 640 x 480 pixels in JPG
Video: 640 x 480 pixels, 30fps in AVI
Package Includes:
1 x Owner’s Manual
1 x Remote Control
1 x DC 3.7V, 380mAh (1.406WH) Li-ion rechargeable battery(Already placed into the battery
compartment on the unit)
1 x USB Charging Cable (For charging only)
4 x Spare Blades
1 x Screwdriver
The specifications and accessories are subject to change without notice.
11

FCC Caution.
(1)§ 15.19 Labelling requirements.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
§ 15.21 Changes or modification warning
Any Changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment.
§ 15.105 Information to the user.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.