Crate&Barrel Mid-Century Spindle Toddler Rail User manual

• Failure to follow these warnings and assembly instructions could result in serious injury or death.
• Read all instructions before assembling toddler rail. Keep instructions for future use.
• For toddler bed use, the minimum age shall be no less than 15 months, and the maximum weight shall not be
greater than 50 lb (22.7 kg).
• Infants can suffocate on soft bedding. Never add a pillow or comforter. Never place additional padding under an
infant.
• To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their backs to sleep, unless
otherwise advised by your physician.
Strangulation Hazard:
• Strings can cause strangulation! DO NOT place items with a string, cord or ribbon around a child’s neck, such as
hood strings or pacifier cords. DO NOT suspend strings over crib or toddler bed, or attach strings to toys for any
reason.
• To help prevent strangulation, tighten all fasteners. A child can trap parts of the body or clothing on loose fasteners.
• DO NOT place crib or toddler bed near windows where cords from blinds or drapes may strangle a child.
Fall Hazard:
• When child is able to pull to standing position, set mattress to lowest position and remove bumper pads, large toys
and other objects that could serve as steps for climbing out.
• When child is able to climb out or reaches the height of 35 inches (90 cm), the crib shall no longer be used and the
child should be placed in a youth or regular bed.
CAUTION: ANY MATTRESS USED IN THIS CRIB
MUST BE AT LEAST 27-1/4 INCHES (69 cm) BY 51-5/8
INCHES (131 cm) WITH A THICKNESS NOT EXCEEDING
6 INCHES (15 cm).
• Check this product for damaged hardware, loose joints, missing parts or sharp edges before and after assembly and
frequently during use. Securely tighten loose bolts and other fasteners. DO NOT use crib if any parts are missing,
damaged, or broken. Contact Crate and Barrel® for replacement parts and instructional literature if needed. DO NOT
substitute parts.
• If refinishing, use a non-toxic finish specified for children’s products.
• Never use plastic shipping bags or other plastic film as mattress covers because they can cause suffocation.
• Infants can suffocate in gaps between crib sides and a mattress that is too small.
• Periodically check to see that all bolts are securely tightened.
• To clean toddler bed: Wipe with clean soft cloth dampened with a mild cleanser and water. Rinse with clean water
using a soft cloth, and dry thoroughly.
• Follow warnings on all products in a toddler rail.
• When a vaporizer is in use, always aim vapor steam away from the toddler bed as well as away from other wood
furniture.
WARNING:
!
!
WARNING:
!
800.967.6696 | crateandbarrel.com
Made in Vietnam - r07
Mid-Century Spindle Toddler Rail Assembly Instructions

NOTE: Hardware will be re-used from crib assembly unless otherwise mentioned
24 - Large bolts 4 - Support pins 2 - Small bolts
(New hardware)
24 - Spring washers
(Pre-attached to large bolts)
24 - Flat washers
(Pre-attached to large bolts)
1 - Small Allen wrench 1 - Large Allen wrench
4 - Bolt caps
800.967.6696 | crateandbarrel.com
WARNING:
CHOKING HAZARD - SMALL PARTS
Small parts present in unassembled state.
Adult assembly required.
This page lists the contents included in the box. Please take
time to identify the hardware as well as the individual
components of the product. As you unpack and prepare for
assembly, place the contents on a carpeted or padded area
to protect them from damage. Please follow the assembly
instructions closely. Improper assembly can result in
personal or property damage.
Note: 2 adults are required to safely assemble this product.
Mid-Century Spindle Toddler Rail Assembly Instructions
Page 1 of 8
Made in Vietnam - r07

800.967.6696 | crateandbarrel.com
Using a large Allen wrench, unfasten 4 bolt caps and carefully remove mattress support panel from corresponding
pins of assembly as shown. Remove 4 support pins from assembly. Set aside hardware and components until further
instructions.
1
Made in Vietnam - r07
Mid-Century Spindle Toddler Rail Assembly Instructions
Page 2 of 8
1 - Toddler rail

800.967.6696 | crateandbarrel.com
With assistance of another adult, remove 1 end panel and 1 side panel from assembly. Using a small Allen wrench,
unfasten 12 large bolts, 12 spring washers and 12 flat washers as shown. Set hardware and components aside until
further instructions.
2
3
Made in Vietnam - r07
Mid-Century Spindle Toddler Rail Assembly Instructions
Page 3 of 8
Remove bottom panel from crib assembly as shown. Set aside component until further instructions.
(Pre-attached to large bolts)

Attach 1 leg A and 1 leg B to toddler rail as shown. Secure, but do not fully tighten, each leg with 2 large bolts, 2 spring
washesr and 2 flat washers, using a small Allen wrench.
Release 1 leg A and 1 leg B to side panel as shown. Using a small Allen wrench, unfasten 2 large bolts, 2 spring washers
and 2 flat washers from each leg as shown.
800.967.6696 | crateandbarrel.com
4
5
Made in Vietnam - r07
Mid-Century Spindle Toddler Rail Assembly Instructions
Page 4 of 8
A
B
A
B
A
A
(Pre-attached to large bolts)
(Pre-attached to large bolts)

800.967.6696 | crateandbarrel.com
Attach toddler rail assembly to 1 end panel with 4 large bolts, 4 spring washers and 4 flat washers as shown. Do not
fully tighten until further instructions.
Attach remaining end panel to assembly with 8 large bolts, 8 spring washers and 8 flat washers as shown. Do not fully
tighten until further instructions.
Made in Vietnam - r07
Mid-Century Spindle Toddler Rail Assembly Instructions
Page 5 of 8
6
7

800.967.6696 | crateandbarrel.com
Locate the lowest hole setting of toddler rail assembly as shown. Fit each support pin into corresponding corner. Make
sure support pin is securely engaged with assembly.
Made in Vietnam - r07
Mid-Century Spindle Toddler Rail Assembly Instructions
Page 6 of 8
8
9
Place bottom panel into assembly as shown. Make sure bottom panel is securely supported by legs and assembly.
Low

800.967.6696 | crateandbarrel.com
Made in Vietnam - r07
Mid-Century Spindle Toddler Rail Assembly Instructions
Page 7 of 8
10
NOTE: Make sure
metal plate of mattress
panel is at the bottom
during assembly
Carefully place mattress support panel onto corresponding pins of assembly and secure with 4 bolt caps as shown.
Attach each cap with large Allen wrench. Do not fully tighten until further instructions.
Insert 1 small bolt into exposed hole of each end panel as shown, using a small Allen wrench. At this point, fully tighten
all bolts. Assembly is now complete.
11

800.967.6696 | crateandbarrel.com
Made in Vietnam - r07
Mid-Century Spindle Toddler Rail Assembly Instructions
Page 8 of 8
Once the toddler bed is in use, periodically check to make sure all bolts are tight, and tighten as necessary. Keep these
instructions for future use.
MAINTENANCE
Upon completion of assembly, be sure all screws, bolts and fastening devices have been tightened securely. Periodically
repeat this check to make sure all screws, bolts and fastening devices are tight. Before each usage or assembly, inspect
toddler bed for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use toddler bed if parts are missing
or broken. DO NOT substitute parts. DO NOT make any alteration to this toddler bed.
CLEANING
Mix together a mild solution of gentle dishwashing liquid and water, apply to toddler bed surface using a soft clean cloth
lightly dampened in the solution. Rinse with clean water again using a soft clean cloth, then dry all surfaces thoroughly with
a soft dry cloth. NO ABRASIVE CLEANERS, SCOURING PADS, STEEL WOOL OR COARSE RAGS SHOULD BE USED TO CLEAN
THIS FINE FURNITURE.
STORAGE
After completing the assembly process you are advised to read and beware of all WARNINGS, CAUTIONS, CLEANING,
STORAGE, USE AND MAINTENANCE notices contained in these instructions. For long term storage of the toddler bed, store
in a cool, dry place and keep away from moisture and extreme temperature changes.