Creative Play HS113 User manual

REF: HS113
pg 1 of 18 01.08.2019
HS113 - OCTAVIA HALF (6M)
Installation Instructions

REF: HS113
pg 2 of 18 01.08.2019
SEATING & SIDES PARTS / ASSEMBLIES
UPRIGHT TIMBERS
PARTS REQUIRED
SIDE ASSEMBLIES x4
SA
SEAT SLATS - INNER x2
SS-I
SEAT SLATS -END x2
SS-E
SEAT SUPPORT x 7
SSA-I (INNER)
SEAT SUPPORT x 2
SSA-E (END)
UPRIGHT MAIN TIMBER
UPRIGHT ADDITIONAL
UMT - QTY x5
UAT - QTY x7

REF: HS113
pg 3 of 18 01.08.2019
PARTS REQUIRED
FLOOR PARTS / ASSEMBLIES
x86
x314
x92
97.M8X120CSK
97.M8X80CSK
97.M8X180CSK
x624
97.D4.5X60 (DECK SCREW)
FLOOR - DECKING
FD
FLOOR SURROUND ASSEMBLY
FSA
FLOOR SUPPORTS
FS
FLOOR ASSEMBLY
FA - a
FLOOR ASSEMBLY
FA - b
FD - QTY X 24 SLATS
FA - a - QTY X 2
FA - b - QTY X 2
FSA - a - QTY X 2
FSA - b - QTY X 2
FSA - c - QTY X 2
FSA - d - QTY X 1
FS - a - QTY X 2
FS - b - QTY X 2
FS - c - QTY X 2

REF: HS113
pg 4 of 18 01.08.2019
PARTS REQUIRED
ROOF ASSEMBLIES
RA
ROOF MAIN SUPPORTS
ROOF BRACES
ROOF SUPPORTS
RS
RB
ROOF TRIM / KING ‘POST’
RT
RM
RT1 - QTY X 1
RT2 - QTY X 1
RT3a - QTY X 3
RT3b - QTY X 2
RT3c - QTY X 4
RT4 - QTY X 2
RT5 - QTY X 1
RA - QTY X 4
RS - a - QTY X 4
RS - b - QTY X 1
RM - QTY X 5
RB - QTY X 5

REF: HS113
pg 5 of 18 01.08.2019
FOUNDATION DETAILS
FGL
UMT UAT
NOTES:
POST HOLES 400MM x 400MM

REF: HS113
pg 6 of 18 01.08.2019
INSTALLATION INSTRUCTIONS
1
2ATTACH FSA - d TIMBER TO REINFORCE FSA TIMBERS SHOWN
POSITION FSA ASSEMBLIES
USING 4X M8X180MM WOOD SCREWS, ENSURE SCREWS ARE INSERTED FROM INSIDE FRAMEWORK
POSITION THESE ON THE GROUND 120MM FACE ON THE OUTSIDE
FSA - al
FSA - ar
FSA - b
FSA - b
FSA - cl
FSA - cr
FSA - d

REF: HS113
pg 7 of 18 01.08.2019
INSTALLATION INSTRUCTIONS
3
4SCREW THE FAS ASSMBLIES TO THE UMT TIMBERS
INSTALL THE UMT TIMBERS
USING - 97.M8X120CSK - QUANTITY X 20
THE 90X90 TIMBER ON THE FSA ASSEMBLIES HELP POSITION THESE
FSA
UMT

REF: HS113
pg 8 of 18 01.08.2019
INSTALLATION INSTRUCTIONS
5
6INSTALL FA - a ASSEMBLIES
USING - 97.M8X180CSK - QUANTITY X 32, ENSURE SCREWS DO NOT CLASH
INSTALL ONE UAT TIMBERS IN CENTRE OF FSA - d TIMBER
USING 2X M8X180MM WOOD SCREWS
NOTES:
TOP FACE OF TIMBER WILL BE FLUSH WITH THE
TOP OF THE ‘INNER’ 90X90 TIMBER

REF: HS113
pg 9 of 18 01.08.2019
INSTALLATION INSTRUCTIONS
7
8ATTACH ADDITIONAL SUPPORTS (UAT)
INSTALL FLOOR SUPPORTS FS - a, b & c
USING 2 X M8X180MM PER TIMBER - SCREWING INTO THE FA ASSEMBLY
USING M8X180MM WOOD SCREWS - 2 FOR EACH END OF TIMBERS
FS - a
FS - b
FS - c
FS - a
FS - b
FS - c
FS - aFS - b
FS - c

REF: HS113
pg 10 of 18 01.08.2019
9
10 ATTACH RM TIMBERS TO KING POST (RT2) AND SCREW TO UPRIGHTS
ATTACH THE RS - a ROOF TIMBERS
USING 2 X M8X120MM & 2 X M8X180MM WOOD SCREWS
USING 2 X M8X80MM WOOD SCREW EITHER END, ENSURE TIMBERS ARE POSITIONED AS SHOWN
INSTALLATION INSTRUCTIONS
NOTES:
ENSURE TIMBERS ARE PRE-DRILLED AND
COUNTERSUNK
TIMBERS ARE POSITIONED LEVEL WITH THE
TOP OF THE UPRIGHT TIMBER
RS - a
NOTES:
ENSURE SCREWS ARE AS SHOWN TO
RIGHT, TAKE CARE NOT TO SPLIT
UPRIGHT TIMBER
2X 180MM SCREWS PER END
2X 120MM PER TIMBER

REF: HS113
pg 11 of 18 01.08.2019
11
12 ATTACH THE RA-L / RA-R ASSEMBLIES TO THE RM TIMBERS
REPEAT FOR THE REMAINING RM TIMBERS
USING - 97.M8X80CSK - QUANTITY X 8 (INTO EACH RM TIMBER EITHER SIDE)
USING 120MM SCREWS INTO THE KING POST AND 180 SCREWS INTO THE UPRIGHT TIMBERS
INSTALLATION INSTRUCTIONS
RA-L
RA-R
RM
RM

REF: HS113
pg 12 of 18 01.08.2019
13
14 ATTACH RS - b TIMBER TO FRONT RM TIMBERS SHOWN
SECURE THE 2 SECTIONS OF ROOF (L - R) TOGETHER & REPEAT
USING 4 M8X180MM WOOD SCREWS
USING - 97.M8X80CSK - QUANTITY X 12 MIDDLE SECTION
INSTALLATION INSTRUCTIONS
NOTES:
REPEAT STEPS 12 & 13 UNTIL ALL RA
PARTS HAVE BEEN ATTACHED
RA

REF: HS113
pg 13 of 18 01.08.2019
15
16 ATTACH THE RT4 & RT5 FRONT TRIM PIECES TO RM TIMBERS
SCREW TRIM TIMBERS TO THE MAIN ROOF SUPPORTS (RM TIMBERS)
USING 20 X M8X80MM WOOD SCREWS
USING 6 X M8X80MM WOOD SCREWS FOR EACH SECTION
INSTALLATION INSTRUCTIONS
RT3a
RT3a
RT3a
RT3b
RT3b
RT3c
RT3c
RT3c
RT3c
FIG 1
NOTES:
RT3 - a / b / c TIMBERS ARE TO BE
POSITIONED AS SHOWN TO ENSURE THE TIMBERS DO
NOT CLASH - SEE FIG 1 - RT3-c SITS BELOW a/b
ENSURE OVERHANG IS AS SHOWN ABOVE - FIG 2
FIG 2
NOTES:
ENSURE RT5 TIMBER IS PLACED OVER
RT4 TIMBER AND SCREWED TOGETHER AS
SHOWN
TOP OF RT35 TRIM SHOULD BE FLUSH
WITH TOP OF TR3 TRIM SLATS ALREADY
INSTALLED
RT3 - a

REF: HS113
pg 14 of 18 01.08.2019
17
18 ATTACH ROOF BRACES - RB
ATTACH THE RT1 TRIM PIECE
USING - 97.M8X120CSK - QUANTITY X 4 PER TIMBER
USING 4 X M8X80MM WOOD SCREWS FOR EACH TIMBER
INSTALLATION INSTRUCTIONS

REF: HS113
pg 15 of 18 01.08.2019
19
INSTALLATION INSTRUCTIONS
INSTALL DECKING AS SHOWN BELOW
USING - 97.D4.5X60 (DECK SCREW) - APPROX 2MM BETWEEN EACH SLAT
NOTES:
WORK FROM FRONT TO BACK - SPACING APPROX 2MM
BETWEEN TIMBERS ENSURE EACH PIECE IS SCREWED TO
ALL SUPPORTS (DOTTED LINE)
DUE TO THE OVERALL SIZE - INSTALL THE FIRST FULL
LENGTH SLAT CENTRALLY THEN ADD 3-4 VERTICAL TIM-
BERS TO COVER THE GAP
NOTES:
USE 2 X DECK SCREWS FOR WHERE DECK IS SCREWED INTO
FLOOR SUPPORTS - GENERALLY 24 X DECK SCREWS PER
SLAT / TIMBER

REF: HS113
pg 16 of 18 01.08.2019
20
21 INSTALL SEAT SUPPORTS
ENSURE ENTRANCE HAS AN SSA-(END) EITHER SIDE & PLACE 1X SSA - I IN CENTRE OF EACH SIDE PANEL
INSTALLATION INSTRUCTIONS
ATTACH SIDE ASSEMBLIES
USING M8X80MM WOOD SCREWS, ENSURE TIMBERS ARE PRE-DRILLED AND COUTNERSUNK
4 SCREWS PER SIDE AS SHOWN
NOTES:
USE 2 X M8X120MM WOOD SCREWS TO SCREW INTO
THE UPRIGHT TIMBER - FIG 3 (THIS WILL NOT BE POS-
SIBLE FOR THE CENTRAL SEAT SUPPORTS)
FURTHER SECURE USING 2 X M8X120MM WOOD
SCREWS, POSITION THESE SCREWS ON THE ‘INSIDE’
AND SCREW INTO THE GROOVE - FIG 4
FIG 4FIG 3

REF: HS113
pg 17 of 18 01.08.2019
22
23 FURTHER SUPPORT THE ROOF USING RB-T TIMBERS
USING - 97.M8X80CSK - QUANTITY X 4 PER ‘WEDGE’
INSTALLATION INSTRUCTIONS
ATTACH SEAT SECTIONS - SS-I &SS-E
USING 4X M8X80MM WOOD SCREWS PER SLAT, SEAT SECTIONS ARE IN SETS - a / b
NOTES:
SCREW INTO THE 43X43 TIMBER SUPPORTS
EITHER SIDE OF THE SEAT SUPPORT ‘UPRIGHT’
SS-Eb SS-Ea SS-Ea
SS-Eb
SS-Ib
SS-Ia
SS-Ib
SS-Ia
NOTES:
RB-T TIMBER BLOCKS SECURES /
SUPPORT THE ADJOINING ROOF
ASSEMBLIES

REF: HS113
pg 18 of 18 01.08.2019
24
INSTALLATION INSTRUCTIONS
INSTALLATION COMPLETE
PLEASE CHECK ALL SCREWS COUNTERSUNK / NEAT SAND ANY TIMBERS AS REQUIRED