Creative Play PARK BENCH - STANDARD CP049/PBS User manual

PARK BENCH - STANDARD
Assembly Instructions
IMPORTANT - If foundation are required support legs will be have been extended 450mm
DOUBLE SIDED VERSION DOUBLE LENGTH VERSION
REF: CP049 /PBS - PARK BENCH STANDARD
pg 1 of 8

REF: CP049 /PBS - PARK BENCH STANDARD
pg 2 of 8
PARTS required
BENCH SLATS - QTY 4 (147mm x 47mm)
BENCH SLAT FRONT - QTY 1 (147mm x 47mm)
TOP TRIM - QTY 1 (147mm x 47mm)
ARM RESTS - QTY 2 (147mm x 47mm)
BENCH SUPPORT (BACK) - QTY 2 (90mm x 90mm)
BENCH SUPPORT (FRONT) - QTY 2 (90mm x 90mm)
T1
T2
T3
T4
T5
T6
*IMPORTANT - if foundations required additional 450mm included
If freestanding use angle cleats and expansion bolts/excalibur bolts to
secure seats onto tarmac
*IMPORTANT - if foundations required additional 450mm included
If freestanding use angle cleats and expansion bolts/excalibur bolts to
secure seats onto tarmac

x4 (angle cleats/brackets)
x8 (180mm brass screws)
OPTIONAL - If installed onto tarmac/concrete
NOT REQUIRED IF SUPPORT POSTS HAVE BEEN EXENDED FOR FOUNDATIONS
x28 (120mm brass screws)
x4(40mm brass screws)
x4 (80mm brass screws)
TOOLS required
REF: CP049 /PBS - PARK BENCH STANDARD
pg 3 of 8
PARTS required continued...
BENCH SLAT SUPPORTS - QTY 2 (90mm x 90mm)
T7
x4
expansion bolts / excalibur bolts
To be used to secrure seats onto tarmac

REF: CP049 /PBS - PARK BENCH STANDARD
SOIL
TIMBER SUPPORT POST
CONCRETE
pg 4 of 8
Foundation Details

If the bench IS pre-assembled JUMP TO STEP
REF: CP049 /PBS - PARK BENCH STANDARD
pg 5 of 8
Assembly Instructions
1
2Position the T5, T6 & T7 timbers
Using 180mm brass screws
Measurement shown is from finsihed ground level - if legs are extended to
allow concrete foundations ADD 450mm (TOTAL 763mm)
T1
T1
T4
T4
T5
T5
T5
T6
T6
T6
T1 T1
T3
7
T7
T7
T7
T2
*Ensure screws are as shown below

REF: CP049 /PBS - PARK BENCH STANDARD
pg 6 of 8
Assembly Instructions
3
4
Repeat for the second set of T5, T6 & T7 timbers
Attach the T1 & T2 timbers to the T7 slat supports
Using 120mm brass screws
Use 4 screws per SLAT (2 each side) ensure they are
uniform
T1
T1
T2
*5mm gap between the T1 timbers
Face of T2 and T6 timber FLUSH/LEVEL

2 x 120mm brass
screws
2 x 80mm brass
screws
REF: CP049 /PBS - PARK BENCH STANDARD
pg 7 of 8
Assembly Instructions
5Attach the T4 (arm rests)
Using 120mm brass screws & 80mm brass screws
*Ensure screws are as shown

REF: CP049 /PBS - PARK BENCH STANDARD
pg 8 of 8
Assembly Instructions
6
7
Attach the T1 & T3 timbers to the T5 seat supports
Using 120mm brass screws
Install the ASSEMBLED BENCH
Using ANGLE CLEATS with 40mm brass screws and EXPANSION BOLTS or CONCRETE INTO GROUND as per foundation drawings
OR
T1
T1
T3
*Lower T1 timber (for back rest) sits on
top of the arm rest
*5mm gap between the T1 timbers
Position angle cleats on the INSIDE of
each SUPPORT
- Use 40mm brass screws to attach
angle cleat to the support legs
- Use expansion bolts or EXCALIBUR
bolts to secure the bolts to the concrete
/ tarmac
Follow the FOUNDATION DETAILS on
Page 4
Use 4 screws per SLAT (2 each side) ensure they are
uniform