Creative Playthings Lexington Premium Pack 17 User manual

LEXINGTON PREMIUM PACK 17
LEXI9WPP17-100 Rev C (05-20)
© Copyright 2018, Creative Playthings
CHILDHOOD STARTS HERE
LEXI9WPP17
L P P 
• Start by assembling the Lexington tower. Instructions and hard-
ware are in the cartons noted at left. The gym is rotated 90° from
the position shown in the instructions.
The components of this gym can be combined with others to
create different play sets. This is the best order of assembly
to create this specic set.
Read this sheet and all instructions included with the
different parts before assembly.
See the Instructions and Owner's Manual included in carton
63007-445 for important safety information.
Dimensions of assembled package:
24' 4" wide x 18' 6" deep x 12' 9" tall
Cartons for this Play Set:
1 63007-421 Lexington Gym 1 (Hardware)
1 63007-422 Lexington Gym 2
1 63007-423 Lexington Gym 3
1 63007-445 Lexington Roof (Hdwre & Instr)
1 SH946-102 Access Ladder, 5ft
1 AG942-400 Access Ladder Handles (Hdwre & Instr)
1 63058-202 4 Position Swing Beam
1 63060-222 9ft Swing Beam Legs (Hdwre & Instr)
1 50546-777 3 Swings, 1 Trapeze
1 15166-400 10 ft. Super Wave Slide
1 SM964-402 Gable Fans (Hdwre & Instr)
1 SM963-402 Dormer (Hdwre & Instr)
1 SH922-800Q Ramp (Hdwre & Instr)
1 AH201-102Q Rock Climbing Wall (Hdwre & Instr)
1 SC909-800Q Lexington Play Walls (Hdwre & Instr)
1 SC910-800Q Lexington Play Floor (Hdwre & Instr)
1 63008-221 Skybox 1 (Hdwre & Instr)
1 63008-222 Skybox 2
1 SJ926-810 Skybox Wood Roof (Hdwre & Instr)
1 SC904-800Q Skybox Play Floor (Hdwre & Instr)
1 15140-400 14ft Swoosh Slide
1 50398-700 Swoosh Skybox Kit (Hdwre & Instr)
2 AG943-400 Slide Handle (Hdwre & Instr)
1 AP970-104 Bubble Panel (Hdwre & Instr)
1 63081-102 Ice Cream Stand (Hdwre & Instr)
15 1/2"
7 1/4"
3"
0"
• Wait to install the Access Ladder, Slide, and
Wall Slats until after the rest of the play set is
complete.
• Lex step 2. Omit the sandbox end from the end
of the gym adjacent to the Skybox. It will be re-
placed with the transition from the Skybox Play
Floor.
• Lex step 7. Do not install the safety rail.
• Lex step 14. Do not install the end wall support
on the Skybox end of the tower.
• Lex step 15. The swing mount isn't needed.
• Lex step 25. Before installing the roof, nd the
post where the swing beam will mount. Drill
7/16" diameter holes through the post at 3",
7-1/4" and 15-1/2" below the top of the post as
Dormers
shown at right. The beam will be mounted to the front of the post
using these holes. Insert one 5/16" weld nut into the top hole on
the inside face of the post. Be sure the threads on the weld nut are
clear, it will be captured by the roof support. Install the roof.
• Mount the Swing Beam using instructions and hardware included
in 63060-222. Mount the beam to the previously drilled holes at
right rather than the way shown in the instructions. You may need
to temporarily disconnect the roof from the post to put the beam in
place.

© Copyright 2018, Creative Playthings
LEXINGTON PREMIUM PACK 17
LEXI9WPP17-100 Rev C (05-20) Page 2
• Once the roof, roof supports, ridge cap and swing beam
are installed, proceed with the Skybox tower.
• Skybox step 2. Omit the sandbox end under the gym. The
oor transition from the Skybox Play Floor will be used
instead.
• Skybox step 11. Use the front posts from The Skybox Roof
(SJ926-810) in place of the post extensions.
• Skybox Step 17. Wait to install the wall slats on the back
where the bubble panel will mount, and the side where the
Swoosh Slide will mount until after installing the bubble
and slide.
• Install the Skybox Wood Roof (SJ926-810).
• Install the Skybox Play Floor (SC904-800Q) and the Lex-
ington Play Floor (SC910-800Q) using the method found
in the Skybox Play Floor instructions on Page 3 titled "In-
stall the Skybox Play Floor adjacent to a gym with a Play
Floor." Some parts of the Lex Play Floor will be cut to t.
• Install the Play Walls (SC909-800Q) on the front, back and
swing end of the main tower.
• Install the Gable Fans (SM964-402).
• Using a ladder, install the Dormers (SM963-402) in the
positions shown on the front page of this guide. Ladder
access will be obstructed by later installations.
• Install the Ice Cream Stand (63081-102).
• Mount the 14ft Swoosh Slide (15140-400) to the front of
the Skybox using the instructions from (50398-700).
• Install the Bubble Panel (AP970-104) above the Ice Cream
Stand.
• Assemble the Rock Climber (AH201-102Q).
• Lean the Access Ladder and Rock Climber as shown
above. Check spacing.
• Secure the access ladder using the method shown in step
17 of the Lexington instructions.
• Complete the Rock Climber installation as instructed in the
rock climber manual.
• Fasten Access Ladder Handles (AG942-400) to the Ac-
cess Ladder.
• Set the Ramp (SH922-800Q) and Super Wave Slide
(15166-400) in place as shown on the front page of this
guide. Check spacing. Make sure the ramp entrance will
clear the ladder up to the skybox.
• Finish securing the ramp.
• Install the slide mount and slide using the method shown
in steps 23 and 24 of the Lexington instructions.
• Install wall slats in the postions shown in images, using
the methods from the Lexington and Skybox instructions.
Gaps must be narrower than 3-1/2" or wider than 9" to
prevent potential head entrapment.
• Mount the hand grips to the entrance wall slats.
• Mount the Slide Handles (AG943-400) above the slides.
• Double-check all fasteners are secure and all recessed
hardware is covered by hole caps.
Swing Beam
Bubble Panel
Gable Fan
Rock Climber
Play Walls Ramp
Ice
Cream
Stand