Creo Trendsetter NEWS SA User manual

www.creo.com
Copyright © 2005 Creo Inc. All rights reserved.
Internal 732-00041A-EN-RevA
Visual Quick Reference
English
653-00979A-EN-A
February 2005
Trendsetter® NEWS SA

1
Trendsetter NEWS SA Operational Lights and What They Mean
Operator interface lights
Operator Interface Lights Operator Action
Imaging Light Flashing green Wait—the device is imaging a plate.
Load Light Flashing green
Semi-automatic mode—load one or two plates for imaging.
OR
Semi-automatic mode—wait, the device is unloading a plate.
Error Light Flashing yellow An error has occurred and the job is suspended.

Trendsetter NEWS SA
2
Trendsetter NEWS SA
Imaging Plates Using Different Workfl ows
Prinergy
Brisque
TIFF Workfl ow
1In Prinergy, click OK to submit the fi le.
1In Brisque, click Submit to submit the fi le.
1In Print Console, click Open to
submit the fi le.
2Right-click the job and
select Approve.
The output device receives the job in Print Console.
The output device receives the job in Print Console.
The output device receives the job.

3
Trendsetter NEWS SA Imaging a Plate
* Refer to the Operator Guide for full details.
2In Print Console:
a. Click Open to submit the fi le. b. Ensure that the correct media
is available for loading.
The load light glows green.
Plate imaging
7Press the Start button. 8Unload the media.
4Position media on the load ramp.
3Remove all slip sheets.
The load light fl ashes green.
The load light glows solid green.
Media alignment label
The imaging light fl ashes green.
5Lower the media gently until it
touches the registration pins.
6Align the media on the load ramp.
Double-wide
(panorama)
Single-wide
(broadsheet)
1Ensure the device is ready.
CAUTION: Wear protective
gloves when handling plates.*
!

Trendsetter NEWS SA
4
Trendsetter NEWS SA
Operator Operations and Maintenance
Operations
Turn on the output device 2
These operations are required for some of
the maintenance procedures listed below.
Turn off the output device 3
Reset the output device 8
Maintenance Work To
Be Done
How
Often
Date Work
Completed
Exterior surfaces Clean
Weekly
Load ramp 1Clean
Plate roller * 9Clean Monthly
Edge detection strips * 10 Clean Every three
months
Compressed air supply
fi lters:
Six months
or as
needed
5 micron fi lter * 4Replace
0.01 micron fi lter * 5Replace
Intake air fi lter * 7Replace
Universal Debris Removal
Cabinet (UDRC) fi lter ** 6Replace As needed N/A
* Procedures for these items are included in this visual quick reference guide.
** Optional equipment—media dependent.
Note: This document is not intended as a substitute for the Trendsetter NEWS SA
Operator Guide. Refer to the operator guide for detailed procedures.
Software may display differently depending on the version of Print Console in use.
4 5
1
3
2
6
7
8
OFF
ON
9
10
Optional

5
Trendsetter NEWS SA Replacing the Air Supply Filters
2
3
7
5 micron fi lter 0.01 micron fi lter
Air supply fi lter kit
Part number 332-00003
2 Turn off the compressed air. 1
2
3
Replacing the 5 Micron Filter
Replacing the 0.01 Micron Filter
Turn off the compressed air.
Bowl
Tab
Unscrew the bowl by pulling the tab
down and turning the bowl to the left.
Remove the old fi lter and
Install the new one.
4Clean inside the bowl.
5Replace the O-ring,
if necessary.
6Reattach the bowl by pushing
it up and turning it to the
right until it clicks. Turn on the compressed air.
90 psi
0.01 micron
fi lter
4Clean inside the bowl.
5Replace the O-ring,
if necessary.
0 psi
0 psi
5 micron
fi lter
Unscrew the bowl by pulling the tab
down and turning the bowl to the left.
Tab
Bowl
0.01 micron
fi lter
0.01 micron
0.01 micron
6Reattach the bowl by pushing
it up and turning it to the
right until it clicks.
Remove the old fi lter and
Install the new one.
* Refer to the Operator Guide for full details.
WARNING: Remove air pressure from the
device before replacing an air fi lter.*
!

Trendsetter NEWS SA
6
Trendsetter NEWS SA
Cleaning Inside the Output Device
Cleaning the Edge Detection Strip
Cleaning the Plate Roller
1To open the front panel:
a. In Print Console software, unlock
the front panel.
b. Rotate the two latches
and lift the front panel.
Rotate the drum to expose the two edge
detection strips.
Dampen a cloth with isopropanol and swipe it along
each strip once, in one direction only.
4
23
2 3
Locate the blue plate roller.
Dampen a cloth with water, and
slide the cloth over the plate roller.
To close the panels:
a. Pull down the front panel
and turn the locking latches.
b. Pull down the top panel
and then push on the two
corners to lock the internal
latches.
The top panel opens automatically.
Edge detection strips
* Refer to the Operator Guide for full details.
WARNING: Risk of electrical shock if liquids are
alowed to run freely into the output device.*
CAUTION: Be careful not to bump your head on
the raised panel.*
!

7
Trendsetter NEWS SA Replacing the Intake Air Filter
2
Remove the fan box panel:
a. Push the upper corners of the fan box panel
in until you hear both latches click.
b. Lift the fan box panel up and out.
Remove the old intake air fi lter
from inside the fan box panel.
b. Push the upper corners of
the fan box panel in until
you hear both latches click.
Intake air fi lter
Part number 55-0700
Fan box panel
1
Clean the intake air fi lter frame. Install the new intake air fi lter. Replace the fan box panel:
a. Lift the fan box panel and lower
it onto the locating pins.
Locating pin
Locating pin
Airfl ow arrows point inward.
Airfl ow arrows point inward.
3 4 5

Trendsetter NEWS SA
8
Trendsetter NEWS SA
Removing a Flyoff
8 9
b. Rotate the two latches
and lift the front panel.
Rotate the drum to expose
the trailing-edge clamps.
Slide the trailing-edge clamps
off the plate.
Fold over the corners
of the plate.
Press the leading-edge
clamps to free the plate.
Clean out any debris
left behind.
In Print Console, click Resume.Reposition the trailing-edge clamps:
a. Align the trailing-edge clamps. b. Slide the trailing-edge
clamps into position.
* Refer to the Operator Guide for full details.
Open the front panel:
a. In Print Console software, unlock
the front panel.
3 4 5 6 7
The top panel opens
automatically.
In Print Console, click Resume.
11
10 Close the panels:
a. Pull down the front panel and rotate
the locking latches.
b. Pull down the top panel, and then push on
the two corners to lock the internal latches.
21 The device suspends activity.
CAUTION: Wear protective
gloves when handling plates.*
!
CREO PRODUCTS LABEL
FABRICATION DRAWING
DESIGNED BY
PART NO.
SCALE
DOC
REV SHEET
SIZE
OF
DRAWN BY
DATE
A
MILLIMETERS
UNLESS SPECIFIED
COPYRIGHT CREO PRODUCTS INC.
C
SP
REV ECO DRAWING CHANGES BY
DATE APPROVED BY
2000:MAR:14
74-3260A A
WARNING STRONG MAGNETIC FIELDS
1) LABEL ADHESIVE: 3M 467 OR EQUIV.
2) MATERIAL: 3M 7980 MATERIAL
3) COLOUR: BLACK GRAPHICS ON BACKGROUND COLORS AS SHOWN
4) TOLERANCE: +/- 1mm
5) COMPUTER FILE AVAILABLE.
6) LABEL TO BE CSA APPROVED - VENDOR ID MARK REQUIRED.
1:1
11
G. BESTR. LEVASSEUR
A D394 2000:MAR:14 GREG BEST
LABEL SPECIFICATIONS
WARNING!
AVERTISSEMENT!
WARNUNG!
STRONG
MAGNETIC
FIELDS
STARKES
MAGNETFELD
74-3260A-A
YELLOW (PANTONE 108C)
BACKGROUND AND EXCLAMATION MARK
WHITE BACKGROUND
CHAMPS
MAGNETIQUE
INTENSE
LABEL SIZE: 26.0mm x 31.0mm
2mm Rad. corners, typ.
CAUTION: If you have an implanted
cardiac pacemaker, ensure that
magnetic clamps are kept more
than 7 cm (2.75 in.) away from the
pacemaker.*