Crestron TSW-560 User manual

TSW-UMB-60-BBI
Wall Mount Back Box for TSW-560/760/1060 & TSW-UMB-60
Installation Guide
3. Ensure that the “TOP” text on the inside of the back box is facing upward, and then
mount the TSW-UMB-60-BBI into an appropriately sized cutout in the mounting
surface as shown in the following illustration. (When making the cutout, refer to the
product dimensions listed in the table of specications on the product website.)
Depending on the installation, forced ventilation may be required.
Mounting the TSW-UMB-60-BBI (Exploded View)
Description
The TSW-UMB-60-BBI provides a recess wall-mounted metal back box for the
Crestron® TSW-UMB-60 Universal Mounting Bracket. The TSW-UMB-60-BBI is designed
for installation in concrete and masonry applications. Conduit knockouts are also provided
on the top and bottom of the back box.
Installation
To install the TSW-UMB-60-BBI, use the following procedure:
NOTE: For some installations, forced venting may be required.
NOTE: Knockout holes are intended for Class 2 wiring only and are 20 mm (13/16") in
diameter.
1. Separate the two halves of the mounting bracket that comes with the TSW-560,
TSW-760, TSW-1060, or TSW-560P touch screens by removing the two 1-1/2"
screws that hold the halves together. Refer to the following illustrations.
Separating the Halves of the Mounting Bracket (Before Separation)
Additional Resources
Visit the product page on the Crestron website (www.crestron.com)
for additional information, including any rmware updates. Use a QR
reader application on your mobile device to scan the QR image.
Remove (2) 1-1/2" screws
Solid mounting
surface (such as
concrete or masonry)
Plaster
TSW-UMB-60-BBI
Metal bracket
(included with
touch screen)
Screws (2):
6-32 x 1/2"
Wiring
Cutout in
mounting
surface
2. Use the two included 6-32 x 1/2" screws to install the front portion of the mounting
bracket assembly onto the back box. Refer to the following illustration.
Installing the Mounting Bracket into the TSW-UMB-60-BBI
Screws (2):
6-32 x 1/2"
TSW-UMB-60-BBI
Metal bracket
(included with
touch screen)
NOTE: Remove the appropriate knockouts on the TSW-UMB-60-BBI before
installation.
NOTE: The rear portion of the mounting bracket can be saved for possible future
use. Only the front portion is required for installing the TSW-UMB-60-BBI.
Separating the Halves of the Mounting Bracket (After Separation)
105 mm
(4.13 in)
68 mm
(2.65 in)
77 mm
(3.00 in)
NOTE: The TSW-UMB-60-BBI can also be mounted vertically for use with the
TSW-560P portrait touch screen. For this installation, ensure that the “TOP” text
on the inside of the back box is facing to the right, and then install the
TSW-UMB-60-BBI into an appropriately sized cutout in the mounting surface.
(Rotate the product 90º to the right to determine the necessary cutout dimensions
for portrait mounting.)

Crestron Electronics, Inc. Installation Guide - DOC. 7958B
15 Volvo Drive Rockleigh, NJ 07647 (2047752)
Tel: 888.CRESTRON 02.17
Fax: [phone] Specications subject to
www.crestron.com change without notice.
This document was written by the Technical Publications department at Crestron.
©2017 Crestron Electronics, Inc.
The product warranty can be found at www.crestron.com/warranty.
The specic patents that cover Crestron products are listed at patents.crestron.com.
Certain Crestron products contain open source software. For specic information, please visit
www.crestron.com/opensource.
Crestron and the Crestron logo are either trademarks or registered trademarks of Crestron
Electronics, Inc. in the United States and/or other countries. Other trademarks, registered trademarks,
and trade names may be used in this document to refer to either the entities claiming the marks and
names or their products. Crestron disclaims any proprietary interest in the marks and names of others.
Crestron is not responsible for errors in typography or photography.