Crestron TMK-12L User manual

Crestron TMK-12L & WMKT-12L
Trim Ring Mount Kits
Installation Guide

This document was prepared and written by the Technical Documentation department at:
Crestron Electronics, Inc.
15 Volvo Drive
Rockleigh, NJ 07647
1-888-CRESTRON
All brand names, product names and trademarks are the property of their respective owners.
©2009 Crestron Electronics, Inc.

Crestron TMK-12L & WMKT-12L Trim Ring Mount Kits
Contents
Trim Ring Mount Kits: TMK-12L & WMKT-12L 1
Description.................................................................................................................................1
Setup ..........................................................................................................................................2
Supplied Hardware ......................................................................................................2
Installation...................................................................................................................4
Resources.................................................................................................................................10
Industry Compliance .................................................................................................10
Reference Documents................................................................................................10
Further Inquiries ........................................................................................................ 10
Future Updates .......................................................................................................... 10
Return and Warranty Policies ..................................................................................................11
Merchandise Returns / Repair Service ...................................................................... 11
CRESTRON Limited Warranty.................................................................................11
Installation Guide – DOC. 6360A Contents •i

Crestron TMK-12L & WMKT-12L Trim Ring Mount Kits
Trim Ring Mount Kits:
TMK-12L & WMKT-12L
Description
Trim Ring Mount Kits are the preferred method of mounting the Crestron Isys®
TPS-12L, TPS-12G-QM-L wall mount touchpanels, and the Isys i/O TPMC-12L
wall mount touchpanel media center when a finished appearance within a neatly
trimmed cutout is required. This application is perfect for wallpapering.
NOTE: If mounting into a material other than drywall (for example, wood lectern,
concrete, or rock) use the cutout template, available in the post-construction kit
WMKT-12L. For concrete and rock mounting material, allow for proper ventilation
before mounting the touchpanel.
There are two Trim Ring Mount Kits. The TMK-12L is a pre-construction accessory.
Pre-construction refers to framed walls prior to hanging drywall. This accessory
must be used with either the Pre-Construction Mount Kit (PMK-12L) or Wall Mount
Back Box Kit (BB-12L).
The WMKT-12L is a post-construction kit. Post-construction refers to framed walls
with drywall hung. This accessory is designed with a mounting plate so that it can be
placed anywhere on a wall without the support of a stud. The mounting plate is also
ideal for installing the touchpanel in a lectern.
NOTE: If necessary, consult the latest revision of the TPS-12L/15L/17L Operations
Guide (Doc. 6355), TPS-12G/15G/17G-QM-L Operations Guide (Doc. 6356) or the
TPMC-12L Operations Guide (Doc. 6686) for a complete list of mounting options.
These documents are available from the Crestron website
(www.crestron.com/manuals).
Installation Guide – DOC. 6360A Trim Ring Mount Kits: TMK-12L & WMKT-12L •1

Trim Ring Mount Kits Crestron TMK-12L & WMKT-12L
Setup
Supplied Hardware
The TMK-12L consists of a metal trim ring that attaches to the BB-12L or
PMK-12L. The WMKT-12L consists of the trim ring found in the TMK-12L as well
as a mounting plate, and a cutout template set.
The mounting plate provides the necessary support for post-construction
applications. Two overlay cutout templates (4007385) are supplied. One is in the
shape of the required opening; the other is similar to a frame, with the inner area of
the frame the shape of the required opening. Separate the wall cutout templates along
the perforated lines to create the two templates. (Refer to the illustrations on pages 3
and 4.) Use the template that is most convenient.
Supplied Hardware for the TMK-12L and WMKT-12L
DESCRIPTION PART NUMBER QUANTITY
Metal Trim Ring 2013001 1
Metal, Plate, Mounting
(WMKT-12L only) 2012963 1
Overlay, Template, Wall Cutout
(WMKT-12L Only) 4007385 1
The dimensions of the TMK-12L & WMKT-12L are shown below and on the next
page.
Dimensional Drawing – Trim Ring
13.08 in
(33.22 cm)
11.22 in
(28.48 cm)
2.20 in
(5.59 cm)
2 •Trim Ring Mount Kits: TMK-12L & WMKT-12L Installation Guide – DOC. 6360A

Crestron TMK-12L & WMKT-12L Trim Ring Mount Kits
Dimensional Drawing – Mounting Plate
11.99 in
(30.45 cm)
0.06 in
(
0
.
15 cm
)
13.63 in
(34.61 cm)
Drywall Cutout Template and Dimensions (supplied with WMKT-12L only), 1 of 2
2 5/16 in
(58 mm) 10 3/4 in
(274 mm)
6 1/4 in
(158 mm)
12 7/8 in
(327 mm)
1 1/16 in
(27 mm)
1/8 in
(3 mm)
11 1/4 in
(286 mm)
11.00 in
(279 mm)
.188 TYP
Installation Guide – DOC. 6360A Trim Ring Mount Kits: TMK-12L & WMKT-12L •3

Trim Ring Mount Kits Crestron TMK-12L & WMKT-12L
Drywall Cutout Template and Dimensions (supplied with WMKT-12L only), 2 of 2
12.00 in
(305 mm)
.188 TYP
1 1/16 in
(27 mm)
11 1/4 in
(286 mm)
11.00 in
(279 mm)
1/8 in
(3 mm)
2 5/16 in
(58 mm)
13 5/8 in
(346 mm) 12 7/8 in
(327 mm) 10 3/4 in
(274 mm)
6 1/4 in
(158 mm)
Installation
This section provides an installation procedure for each Trim Ring Mount Kit. The
“TMK-12L Procedure” starts below and the “WMKT-12L Procedure” starts on page
6. Be sure to review each procedure before starting.
TMK-12L Procedure
This section provides the necessary steps for the assembly of the TMK-12L with
either the BB-12L or PMK-12L. It is assumed that the BB-12L or PMK-12L has
been secured to the stud according to the instructions in the latest revisions of their
Installation Guides (Doc. 6357 and Doc. 6358 respectively). It is also assumed that
drywall is in place and a cutout is made in the drywall along the inside of the
mounting plate for touchpanel installation.
Complete the steps in the order provided. The only tool required and not supplied is
a level.
CAUTION: Allow an air gap of at least 12 inches (30.48 cm) in the wall cavity
above and below the touchpanel for heat dissipation.
NOTE: When installing into the PMK-12L, verify that the 18 AWG bus wire
securing the cables for the touchpanel remains attached.
4 •Trim Ring Mount Kits: TMK-12L & WMKT-12L Installation Guide – DOC. 6360A

Crestron TMK-12L & WMKT-12L Trim Ring Mount Kits
1. Verify that the cutout in the drywall is as clean and level as possible.
2. Insert the symmetrical trim ring into the opening, as shown in the
illustration below.
Insert Trim Ring into Opening
TRIM RING
(2013001)
NOTE: MAKE DRYWALL CUTOUT AS
LEVEL AND CLEAN AS POSSIBLE. THE
TRIM RING ONLY ALLOWS MINOR
ADJUSTMENTS OF THE TOUCHPANEL.
DRYWALL
NOTE: The required PMK-12L or BB-12L is not shown.
3. When the trim ring is in position, bend the top two flanges of the ring
upward and the bottom two flanges downward.
• If mounting into the PMK-12L, bend the flanges approximately 90
degrees.
• If mounting into the BB-12L, bend the flanges back as far as they can
go.
4. Run the necessary cables for the touchpanel and secure them behind the
drywall.
5. The touchpanel can be installed using the eight tapped holes in the
TMK-PMK-15L (or BB-15L). Refer to the latest revision of the
TPS-12L/15L/17L Operations Guide (Doc. 6355),
TPS-12G/15G/17G-QM-L Operations Guide (Doc. 6356) or the TPMC-12L
Operations Guide (Doc. 6686) for touchpanel installation details. Refer also
to the comprehensive illustration shown on the following page.
Installation Guide – DOC. 6360A Trim Ring Mount Kits: TMK-12L & WMKT-12L •5

Trim Ring Mount Kits Crestron TMK-12L & WMKT-12L
TPS-12L Mounting Using the TMK-12L – Exploded View
PMK-12L
TPS-12L
(Bezel Removed)
TRIM RING
(2013001)
DRYWALL
(Bezel)
MOUNTING SCREWS (8)
#06-32 X 1-1/2" (2007254)
NOTE: MOUNTING SCREWS
SUPPLIED WITH TOUCHPANEL.
WMKT-12L Procedure
This section provides the necessary steps for the assembly and installation of the
WMKT-12L into a wall. Review the procedure first, then complete the steps in the
order provided. The only tools or materials required and not supplied are a drywall
saw or equivalent and a level.
CAUTION: Allow an air gap of at least 12 inches (30.48 cm) in the wall cavity
above and below the touchpanel for heat dissipation.
1. Locate an area on the wall that is free of miscellaneous wiring and studs.
2. Make a small hole near the middle of the designated site; verify that the
location is suitable.
NOTE: Make the cutout as level and smooth as possible. The mounting plate allows
for only minor leveling adjustments. If a larger cutout is made accidentally, consider
purchasing the Crestron Mud Mount Kit, MMK-12L. Together with the mounting
plate supplied with the WMKT-12L, it provides a cost-effective means of correction.
Essentially, the combination of these two kits makes up the Crestron Mud Mount Kit
for the wall, WMKM-12L. Simply follow the “WMKM-12L Procedure” in the latest
revision of the Mud Mount Kits Installation Guide (Doc. 6359).
3. Use the drywall saw or equivalent and the provided drywall cutout template
to produce an accurate, clean and level cutout in the drywall.
6 •Trim Ring Mount Kits: TMK-12L & WMKT-12L Installation Guide – DOC. 6360A