Crestron TSW-560-TTK Dimensional drawing

DO GUIDE
DO Assemble the TSW-560/760/1060-SMK
Assemble the Swivel Mount
To assemble the swivel mount:
1. Attach and secure the swivel mechanism tube to the bottom of the TSW-560/760/1060-TTK using the three included 6-32 x 3/16" screws.
2. Remove the paper liner from the felt washer and attach the washer to the bottom of the swivel mechanism tube.
3. If the Ethernet cable is routed to exit through the bottom of the TSW-560/760/1060-TTK, feed the full length of the cable through the swivel
mechanism tube.
4. Use the included template to prepare the mounting surface.
5. Using the six mounting holes on the swivel stop plate as a template, drill pilot holes in the mounting surface. The holes should be 0.093" (2 mm)
minimum diameter, 0.115" (3 mm) maximum diameter, and 0.35" (9 mm) maximum depth.
6. Attach the swivel stop plate to the bottom of the mounting surface using the six included 8-8B x 1/2" screws.
7. Pass the swivel mechanism tube attached to the TSW-560/760/1060-TTK down through the mounting hole and swivel stop plate.
NOTE: The swivel stop plate has a permanently installed limiting screw to prevent the swivel mechanism from spinning and tangling the touch
screen cable.
TSW-560/760/1060-TTK and TSW-560/760/1060-SMK
TableTop Kits and Swivel Mount Kit for TSW-560/760/1060
The Crestron®TSW-560-TTK, TSW-760-TTK, and TSW-1060-TTK are functionally identical. For simplicity within this guide, the term
“TSW-560/760/1060-TTK” is used except where noted.
DO Prepare the TSW-560/760/1060-TTK
The TSW-560/760/1060-TTK includes parts for routing device cabling through either the bottom or rear of the unit.
Routing the Cable though the Bottom of the TSW-560/760/1060-TTK
The TSW-560/760/1060-TTK has a circular opening in its metal base that allows an Ethernet cable to pass through the bottom, enabling network connection
when the unit is attached to the TSW-560/760/1060-SMK Swivel Mount Kit (sold separately).
Routing the Cable though the Rear of the TSW-560/760/1060-TTK
Modication is necessary to install the TSW-560/760/1060-TTK on a at surface. Replace the rear plastic cap with the provided grommet to route the
Ethernet cable through the rear of the unit. The grommet serves as a strain relief on the cable.
1. Remove the two screws on the bottom of the unit that hold the metal bracket. Retain the metal bracket and screws.
2. Remove the rear plastic cap by pressing the top of the cap inward until it unsnaps.
3. Insert the Ethernet cable through the rear opening of the TSW-560/760/1060-TTK and attach the provided grommet to the cable.
4. Secure the grommet to the back of the TSW-560/760/1060-TTK by pressing it into place.
NOTE: For added security, refer to “DO Use the Security Option” and follow the procedure. For standard mounting, proceed to the next step.
5. Reinstall the metal bracket using the screws removed in step 1.
DO Mount the Touch Screen in the TSW-560/760/1060-TTK
To mount the touch screen:
1. Connect the Ethernet cable to the touch screen.
2. Gently pull excess cable out through the rear of the TSW-560/760/1060-TTK as the touch screen and tabletop kit converge.
3. Seat the touch screen in the TSW-560/760/1060-TTK fully to engage the spring-loaded retainers built into the metal bracket.
DO Check the Box
QUANTITY ITEM PART NUMBER
Items for TSW-560/760/1060-TTK Only
2 Screw, M3 x 0.5 x 6 mm, Pan Head, Phillips 2047840
1Template, Cutout 4525014
Items for TSW-560/760/1060-TTK-B-S Only
1Grommet, Rubber, Black 2047839
Items for TSW-560/760/1060-TTK-W-S Only
1Grommet, Rubber, White 2047838
Items for TSW-560/760/1060-SMK Only
1Nut, 7/8"-14 2017632
1Plate, Swivel Stop 4504353
3 Screw, 6-32 x 3/16", Pan Head, Phillips 2007202
2 Screw, 8-32 x 1/8", Cap Head, Socket 2017634
6 Screw, 8-8B x 1/2", Pan Head, Phillips 2017784
1Template, Cutout 4525014
1 Washer, 1.75" OD, 15/16" ID, 0.14" TH 2017633
1 Washer, Cork/Rubber, 1.75" OD, 0.94" ID, 1/16" TH 2017614
1 Washer, Felt, 2.65" OD, 0.93" ID 2024711
1Washer, Keyed 4506321
1 Washer, Rubber, 1.75" OD, 0.94" ID, 1/16" TH 2017615
TSW-560/760/1060-TTK
Swivel mechanism tube
Screws (3) 6-32 x 3/16"
Felt washer
Remove these screws
to release the metal bracket.
Metal bracket
Plastic cap
Bottom of TSW-560/760/1060-TTK

DO GUIDE DOC. 7928B (2047266) 05.18
Specications subject to change without notice.
8. Attach or slide the included hardware up onto the swivel mechanism tube in the order indicated in the illustration that follows step 9.
NOTE: Orient the keyed metal washer tab to face away from the permanently installed limiting screw.
9. Adjust the tightness of the 7/8"-14 nut to achieve the desired swivel assembly motion resistance. Use a flat tool, such as a large flat-head
screwdriver, in the slot on the bottom of the swivel mechanism tube to hold the tube steady while tightening the nut.
Customize the Swivel Range
Reposition the two 8-32 x 1/8” screws placed on the swivel stop plate to customize the swivel range (330-degree rotation, maximum). Refer to the following
illustrations for details.
DO Use the Security Option
Use the two included M3 x 0.5 x 6 mm screws to lock the touch screen to the TSW-560/760/1060-TTK.
1. Remove the two screws on the bottom of the unit that hold the metal bracket. Retain the metal bracket and screws.
2. Place the touch screen face down on a clean, soft cloth (not provided) and remove the two 1/2" long screws from the rear assembly. Retain these
screws to restore the touch panel without the security option, if necessary.
3. Secure the metal bracket to the rear assembly.
a. Position the bracket correctly (right side up, as shown above).
b. Secure the bracket with two included M3 x 0.5 x 6 mm screws. To prevent damage to threads, turn each screw counterclockwise until it
engages the thread.
c. Tighten the screws to 3 in/lb.
4. Secure the touch screen to the TSW-560/760/1060-TTK.
a. Connect the Ethernet cable to the touch screen while it remains face down.
b. Position the TSW-560/760/1060-TTK over the touch screen and gently pull any excess cable out through the rear of the tabletop accessory
until the two units come together.
c. Secure the TSW-560/760/1060-TTK to the touch screen with the two screws removed in step 1.
The specic patents that cover Crestron products are listed at www.crestron.com/legal/patents.
The product warranty can be found at www.crestron.com/legal/sales-terms-conditions-warranties.
Certain Crestron products contain open source software. For specic information, visit www.crestron.com/legal/open-source-software.
Crestron and the Crestron logo are either trademarks or registered trademarks of Crestron Electronics, Inc., in the United States and/or other countries. Other trademarks, registered trademarks,
and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of
others. Crestron is not responsible for errors in typography or photography.
This document was written by the Technical Publications department at Crestron.
©2018 Crestron Electronics, Inc.
DO Learn More
Visit the website for additional information and the latest rmware updates.
To learn more about this product, use a QR reader application on your
mobile device to scan the QR image.
Crestron Electronics
15 Volvo Drive, Rockleigh, NJ 07647
888.CRESTRON | www.crestron.com
Swivel mechanism tube
Slot in tube
Table or mounting surface (front edge)
Mounting holes (6)
in swivel stop plate
Screws (2) 8-32 x 1/8"
Bottom side of table or mounting surface
Screws (6) 8-8B x 1/2"
Cork and rubber washer
Keyed metal washer
Rubber washer
Steel washer
Nut 7/8"-14
Mounting hole
Permanently installed limiting screw
Swivel stop plate
Remove
these
screws.
Screws (2)
M3 x 0.5 x 6 mm
Metal
bracket
TSW-560-TTK T SW-76 0-T T K T SW-10 60 -T TK TSW-560/760/1060-SMK
Keyed metal
washer tab
where swivel
motion starts
Six locations
for additional
limiting screws
Permanent
limiting screw
30º 90º
135º
Insert the two
limiting screws
to set the desired
swivel range.
Permanent
limiting screw
Metal bracket
Remove these
screws to release
the metal bracket.
Bottom of TSW-560/760/1060-TTK