CREVIS FnIO SSeries User manual

제품을 사용하시기 전에
저희 (주)크래비스 제품을 구입해 주셔서 감사합니다. 제품의 효율적인 사용을 위하여 반드시 본사용 설명서의 내용을 숙지 하신 후
사용해 주십시오.
안전상의 주의 사항 *경고와 주의로 구분되어 있으니, 필히 숙지 하여 주십시오.
●전원이 인가된 상태에서 단자대를 만지지 마십시오.
●전원이 인가된 상태에서 제품을 조립하지 마십시오.
●제품내부에 금속성 이물질이 유입되지 않도록 하십시오.
●전원이 인가된 상태에서 배선 작업을 하지 마십시오.
●배선 작업은 전기공사 전문가가 해주십시오.
지시사항을 위반하였을 때, 심각한 상황을 초래하여 사망 또는 중상을 입을 가능성이 있는 경우
●제품의 정격전압 및단자배열을 확인 후배선하여 주십시오.
●주변 온도가 55℃를넘는 장소는 피해 주십시오.
●직사 광선이 직접 노출된 장소는 피해 주십시오.
●주변 습도가 85%를넘는 장소는 피해 주십시오.
●가연성 물질이 있는 주변에 설치하지 마십시오.
●제품에 직접 진동이 인가되지 않도록 하십시오.
●전문 A/S요원 외에는 제품을 분해,수리,개조하지 마십시오.
●사용설명서에 명기된 환경조건에서 사용해 주십시오.
●확장 연결되는 모듈의 부하는 규정된 정격 이내로 사용해 주십시오.
지시사항을 위반하였을 때, 경미한 상해나 제품손상 및대물손해가 발생할 가능성이 있는 경우
1. NA-9189 제품 사양
FieldBus Input/Output System
■ModBus/TCP Network Adapter
■PROFIBUS Network Adapter
■Digital Input / Output
■Analog Input / Output
사용설명서
NA-9189
FnIO S-series
Class 2, adjacent to voltage rating (30Vmax.)
화재,감전사고, 오동작의 원인이 됩니다.
화재,감전사고, 오동작의 원인이 됩니다.
화재,감전사고, 오동작의 원인이 됩니다.
화재,감전사고, 오동작의 원인이 됩니다.
화재의 원인이 됩니다.
화재 및감전의 원인이 됩니다.
화재 및감전사고의 원인이 됩니다.
감전, 화재, 오동작 또는 제품 열화의 원인이 됩니다.
화재, 오동작 또는 고장의 원인이 됩니다.
감전사고 및오동작의 원인이 됩니다.
화재, 감전사고 및오동작의 원인이 됩니다.
화재, 감전사고 및오동작의 원인이 됩니다.
감전사고 및오동작의 원인이 됩니다.
화재, 감전사고 및오동작의 원인이 됩니다
구분 일반사양 구분 상세사양
사용/보존 온도 -20℃~55℃ / -40℃~85℃ Network 방식 Modbus/TCP
사용/보존습도 5% ~ 90% 단, 이슬이 맺히지 않을 것Cable EtherNet Cable(Shield Cable)
내진동/내충격 IEC68-2-6(2G) / 10G Cable 길이(m) Up to 100m from Ethernet Hub
EMC/ESD EN50082 / EN50081 통신속도(Kbps) 10/100Mbps
확장 모듈 위치 FnIO-S series의가장 왼쪽에 장착 확장모듈수 Max. 32 module
사용환경 부식성 가스가 없고, 먼지가 심하지
않을 것Max. Nodes Limited by Ethernet Specification
필드 공급전압 Class 2, 24VDC
24VDC (11VDC ~ 28.8VDC)Operation Mode 8 MODBUS/TCP, 4 HTTP, BOOTP.
TBD
필드 공급전류 최대 10A 최대 Digital I/O Input : 2016점/ Output : 2016점
FnBus공급전류 최대 1.5A@5Vdc 최대 Analog I/O Input : 126Ch / Output : 126Ch
Baud rate 설정 자동설정 최대 Byte수Input : 252Bytes / Output : 252Bytes
외형치수 45mm ×99mm ×70mm IP Address Setting Window Command, BOOTP
무게 150g 내부 소비전류 60mA typical @24Vdc
인증 UL / cUL / CE / FCC / DNV / LR /
RoHS(EU, China)
Update date : 2013.1.30
TCP/IP
* Specifications and designs could be changed without advance Notice
* Power Isolators must be used according to the usage of 5VDC/24VDC/48VDC or AC Voltage modules
CVS-18-04A-011 Rev 2.02

2. 통신선 배선 및전원선 배선 방법
▶2-1. 통신선 및System 전원선 배선
3. 모듈 설치 방법
▶3-1. Din-Rail에모듈 장착 방법
▶3-2. Din-Rail에서 모듈 탈착 방법
①Din rail 고정용 고리를 (–) 자드라이버를
이용하여 아래로 내려주십시오.
①Din-Rail 위에서 아래 방향
으로 살짝 눌러 주십시오.
②딸칵 소리가 날때까지 눌러
주시면 장착이 완료됩니다.
②모듈의 양쪽 끝을 잡고 위방향
으로 들어 주시면 탈착 됩니다.
* System 전원과 Field 전원은 반드시 별도의 전원을 사용하시기 바랍니다.

4. 상태 LED
* 상태 표시 LED 창설명
Item LED is State To indicate :
MOD
LED
Off No Power No power is supplied to the unit.
Green Device Operational The unit is operating in normal condition.
Flashing
Green Device in Standby The device needs commissioning due to configuration missing, incomplete or incorrect.
Green/Red
Toggle MODBUS Error MODBUS error such as watchdog error, etc.
Flashing
Red Minor Fault Recoverable Fault - EEPROM sum check error.
Red Unrecoverable Fault The device has an unrecoverable fault.
- Memory error or CPU watchdog error.
LINK
LED
Off Not Powered Device is not on-line or may not be powered
Green Adapter physical
connected Adapter Ethernet Controller Physically connected
ACTIVE
LED
Off Not Powered Device is not on-line or may not be powered
Flashing
Green Adapter exchange data Adapter (Slave) exchange data/Traffic present. About 10msec flashing.
Field Power
LED Off Not Supplied Field Power Not supplied 24V dc field power
Green Supplied Field Power Supplied 24V dc field power
I/O
LED
Off Not Powered
No IO Module Device has no IO module or may not be powered
Flashing
Green FnBus On-line, Do not Exchanging I/O FnBus is normal but does not exchanging I/O data (Passed the IO module configuration).
Green FnBus Connection,
Run Exchanging IO Exchanging I/O data
Red FnBus connection fault
during exchanging IO
One or more IO module occurred in fault state.
- Changed IO module configuration.
- FnBus communication failure.
Flashing
Red Expansion Configuration Failed
Failed to initialize IO module
- Detected invalid IO module ID.
- Overflowed Input / Output Size
- Too many IO module
- Initial protocol failure
* 사양 및디자인은 예고 없이 변경될 수있습니다.
㈜크래비스
경기도 용인시 기흥구 기곡로 29-4
TEL : [phone] FAX : [phone] Homepage : www.crevis.co.kr
TCP/IP

MEMO
* 사양 및디자인은 예고 없이 변경될 수있습니다.
TCP/IP
㈜크래비스
경기도 용인시 기흥구 기곡로 29-4
TEL : [phone] FAX : [phone] Homepage : www.crevis.co.kr

FieldBus Input/Output System
■ModBus/TCP Network Adapter
■PROFIBUS Network Adapter
■Digital Input / Output
■Analog Input / Output
■Special Module
Quick Guide
FnIO S-series
NA-9189
1. NA-9189 Specification
* Specifications and designs could be changed without advance Notice
Class 2, adjacent to voltage rating (30Vmax.)
ITEM SPECIFICATION ITEM SPECIFICATION
Surrounding Air
Temp./
Ambient Temp. -20℃~55℃ / -40℃~85℃ Network Type Modbus/TCP
Relative Humidity 5% ~ 90% without condensation Cable EtherNet Cable(Shield Cable)
Durable-vib./impact IEC68-2-6(2G) / 10G Cable Length(m) Up to 100m from Ethernet Hub
EMC/ESD EN50082 / EN50081 Comm. Sp(Kbps) 10/100Mbps
Mount Position On the left of FnIO-S series Expansion No. Max. 32 module
Atmosphere Not so dusty without corrosive gas Max. node Limited by Ethernet Specification
Field Supp.Volt. Class 2, 24VDC
24VDC (11VDC ~ 28.8VDC)Max. Digital I/O Input :
2016points/Output:2016points
Field Supp. Cur. Max. 10A Max. Analog I/O Input : 126Ch / Output : 126Ch
FnBus Sup. Cur Max. 1.5A@5Vdc Max. Byte size Input : 252Bytes / Output : 252Bytes
Baud rate set Auto-negotiation Operation Mode 8 MODBUS/TCP, 4 HTTP, BOOTP.
Size 45mm ×99mm ×70mm IP Address setting Window Command, BOOTP
Weight 150g Power Dissipation 60mA typical @24Vdc
Certification UL / cUL / CE / FCC / DNV / LR /
RoHS(EU, China)
TCP/IP
Cautions for your Safety
Do not assemble the products and wire with power applied to the system. Else it may cause an electric arc, which can result into unexpected
and potentially dangerous action by field devices. Arching is explosion risk in hazardous locations. Be sure that the area is non-hazardous or
remove system power appropriately before assembling or wiring the modules.
Do not touch any terminal blocks or IO modules when system is running. Else it may cause the unit to an electric shock or malfunction.
Keep away from the strange metallic materials not related to the unit and wiring works should be controlled by the electric expert engineer.
Else it may cause the unit to a fire, electric shock or malfunction.
If you don’t follow the directions, it could cause a personal injury, damage to the equipment or explosion
If you disobey the instructions, there may be possibility of personal injury, damage to equipment or
explosion. Please follow below Instructions.
Check the rated voltage and terminal array before wiring. Avoid the circumstances over 55℃of temperature. Avoid placing it directly in the
sunlight.
Avoid the place under circumstances over 85% of humidity.
Do not place Modules near by the inflammable material. Else it may cause a fire.
Do not permit any vibration approaching it directly.
Go through module specification carefully, ensure inputs, output connections are made with the specifications. Use standard cables for wiring.
Use Product under pollution degree 2 environment.
Before using the unit
*We appreciate you for purchasing CREVIS Products. To use the units more effectively, please read this quick guide and refer to
the respective user manual for further details.
Warning!
Caution!
* Power Isolators must be used according to the usage of 5VDC/24VDC/48VDC or AC Voltage modules

2. How to wire communication & Power
▶2-1. Wiring of communication & System power line
3. Module Mounting
▶3-1. How to mount on Din-Rail
▶3-2. How to dismount from Din-Rail
①Pull down the locking mechanism by using
(- ) screw driver as the following pictures ;
①Press down the module lightly
on the Din-Rail until it clicks . ②Press down till you can hear “click”forcomplicatedmount.
②Pull up the module to remove
from the din rail .
* Make sure System Power and Field Power must be supplied via SMPS separately .

* Status LED Window Description
4. STATUS LED
Item LED is State To indicate :
MOD
LED
Off No Power No power is supplied to the unit.
Green Device Operational The unit is operating in normal condition.
Flashing
Green Device in Standby The device needs commissioning due to configuration missing, incomplete or incorrect.
Green/Red
Toggle MODBUS Error MODBUS error such as watchdog error, etc.
Flashing
Red Minor Fault Recoverable Fault - EEPROM sum check error.
Red Unrecoverable Fault The device has an unrecoverable fault.
- Memory error or CPU watchdog error.
LINK
LED
Off Not Powered Device is not on-line or may not be powered
Green Adapter physical
connected Adapter Ethernet Controller Physically connected
ACTIVE
LED
Off Not Powered Device is not on-line or may not be powered
Flashing
Green Adapter exchange data Adapter (Slave) exchange data/Traffic present. About 10msec flashing.
Field Power
LED Off Not Supplied Field Power Not supplied 24V dc field power
Green Supplied Field Power Supplied 24V dc field power
I/O
LED
Off Not Powered
No IO Module Device has no IO module or may not be powered
Flashing
Green FnBus On-line, Do not Exchanging I/O FnBus is normal but does not exchanging I/O data (Passed the IO module configuration).
Green FnBus Connection,
Run Exchanging IO Exchanging I/O data
Red FnBus connection fault
during exchanging IO
One or more IO module occurred in fault state.
- Changed IO module configuration.
- FnBus communication failure.
Flashing
Red Expansion Configuration Failed
Failed to initialize IO module
- Detected invalid IO module ID.
- Overflowed Input / Output Size
- Too many IO module
- Initial protocol failure
* Specifications and designs may be changed without advance Notice.
CREVIS Co., Ltd
29-4, Gigok-ro, Giheung-gu, Yongin-si, Gyeonggi-do, Korea 446-930
TEL : [phone] FAX : [phone]
Homepage : www.crevis.co.kr
TCP/IP

MEMO
* Specifications and designs may be changed without advance Notice.
TCP/IP
CREVIS Co., Ltd
29-4, Gigok-ro, Giheung-gu, Yongin-si, Gyeonggi-do, Korea 446-930
TEL : [phone] FAX : [phone]
Homepage : www.crevis.co.kr