CREVIS FnIO S Series NA-9171 User manual

제품을 사용하시기 전에
저희 (주)크래비스 제품을 구입해 주셔서 감사합니다. 제품의 효율적인 사용을 위하여 반드시 본사용 설명서의 내용을 숙지 하신
후사용해 주십시오.
안전상의 주의 사항 *경고와 주의로 구분되어 있으니, 필히 숙지 하여 주십시오.
●전원이 인가된 상태에서 단자대를 만지지 마십시오.
●전원이 인가된 상태에서 제품을 조립하지 마십시오.
●제품내부에 금속성 이물질이 유입되지 않도록 하십시오.
●전원이 인가된 상태에서 배선 작업을 하지 마십시오.
●배선 작업은 전기공사 전문가가 해주십시오.
지시사항을 위반하였을 때, 심각한 상황을 초래하여 사망 또는 중상을 입을 가능성이 있는 경우
●제품의 정격전압 및단자배열을 확인 후배선하여 주십시오.
●주변 온도가 55℃를넘는 장소는 피해 주십시오.
●직사 광선이 직접 노출된 장소는 피해 주십시오.
●주변 습도가 85%를넘는 장소는 피해 주십시오.
●가연성 물질이 있는 주변에 설치하지 마십시오.
●제품에 직접 진동이 인가되지 않도록 하십시오.
●전문 A/S요원 외에는 제품을 분해,수리,개조하지 마십시오.
●사용설명서에 명기된 환경조건에서 사용해 주십시오.
●확장 연결되는 모듈의 부하는 규정된 정격 이내의 것을 연결하십시오.
지시사항을 위반하였을 때, 경미한 상해나 제품손상 및대물손해가 발생할 가능성이 있는 경우
1. NA-9171 제품 사양
FieldBus Input/Output System
■Serial Network Adapter
■PROFIBUS Network Adapter
■Digital Input / Output
■Analog Input / Output
사용설명서
NA-9171
FnIO S-series
감전사고 및오동작의 원인이 됩니다.
화재, 감전사고 및오동작의 원인이 됩니다.
화재, 감전사고 및오동작의 원인이 됩니다.
감전사고 및오동작의 원인이 됩니다.
화재, 감전사고 및오동작의 원인이 됩니다
화재,감전사고, 오동작의 원인이 됩니다.
화재,감전사고, 오동작의 원인이 됩니다.
화재,감전사고, 오동작의 원인이 됩니다.
화재,감전사고, 오동작의 원인이 됩니다.
화재의 원인이 됩니다.
화재 및감전의 원인이 됩니다.
화재 및감전사고의 원인이 됩니다.
감전, 화재, 오동작 또는 제품 열화의 원인이 됩니다.
화재, 오동작 또는 고장의 원인이 됩니다.
Update date : 2013.1.30
구분 일반사양 구분 상세사양
사용/보존 온도 -20℃~55℃ / -40℃~85℃ Network 방식 ModBus-RS232
사용/보존습도 5% ~ 90% 단, 이슬이 맺히지 않을 것Cable Serial Twist cable
내진동/내충격 IEC68-2-6(2G) / 10G Cable 길이(m) 15m
EMC/ESD EN50082 / EN50081 통신속도(Kbps) 1.2k ~ 115.2kbps
확장 모듈 위치 FnIO-S series의가장 왼쪽에 장착 확장 모듈 수Max. 32 module
사용환경 부식성 가스가 없고,
먼지가 심하지 않을 것Number of Nodes 1개
필드 공급전압 Class 2, 24VDC
24VDC (11VDC ~ 28.8VDC) Operating Mode Polling
필드 공급전류 최대 10A 최대 Digital I/O Input : 2016점/ Output : 2016점
FnBus공급전류 최대 1.5A@5Vdc 최대 Analog I/O Input : 126Ch / Output : 126Ch
Isolation
System power to internal logic : Non-
isolation
System power to I/O driver : Isolation
최대 Byte수Input : 252Bytes / Output : 252Bytes
외형치수 45mm ×99mm ×70mm Node 번호 설정 Rotary 스위치 2개(x10, x1)
무게 150g 내부 소비전류 70mA(NA-9171 1개Module)
인증 UL / cUL / CE / FCC / RoHS(EU, China)
RS232
Class 2, adjacent to voltage rating (30Vmax.)
* Power Isolators must be used according to the usage of 5VDC/24VDC/48VDC or AC Voltage modules
CVS-18-04A-008 Rev 2.02

FieldBus Input/Output System
■Serial Network Adapter
■PROFIBUS Network Adapter
■Digital Input / Output
■Analog Input / Output
■Special Module
Quick Guide
FnIO S-series
NA-9171
1. NA-9171 Specification
* Specifications and designs could be changed without advance Notice
Class 2, adjacent to voltage rating (30Vmax.)
ITEM SPECIFICATION ITEM SPECIFICATION
Surrounding Air
Temp./
Ambient Temp. -20℃~55℃/ -40℃~85℃Network Type ModBus-RS232
Relative Humidity 5% ~ 90% without condensation Cable Serial Twist cable
Durable-
vib./impact IEC68-2-6(2G) / 10G Cable Length(m) 15m
Operating Mode Polling
EMC/ESD EN50082 / EN50081 Comm. Sp(Kbps) 1.2k ~ 115.2kbps
Mount Position On the left of FnIO-S series Expansion No. Max. 32 module
Atmosphere Not so dusty without corrosive gas Max. node 1 node
Field Supp.Volt. Class 2, 24VDC
24VDC (11VDC ~ 28.8VDC)Max. Digital I/O Input : 2016point / Output : 2016point
Field Supp. Cur. Max. 10A Max. Analog I/O Input : 126Ch / Output : 126Ch
FnBus Sup. Cur Max. 1.5A@5Vdc Max. Byte size Input : 252Bytes / Output : 252Bytes
Isolation System power to internal logic : Non-isolation
System power to I/O driver : Isolation Node No. Setting Rotary Switch 2ea(x10, x1)
Size 45mm ×99mm ×70mm Power Dissipation 70mA typical @24Vdc
Weight 150g Certification UL / cUL / CE /FCC / RoHS (EU, China)
RS232
Cautions for your Safety
Do not assemble the products and wire with power applied to the system. Else it may cause an electric arc, which can result into unexpected
and potentially dangerous action by field devices. Arching is explosion risk in hazardous locations. Be sure that the area is non-hazardous or
remove system power appropriately before assembling or wiring the modules.
Do not touch any terminal blocks or IO modules when system is running. Else it may cause the unit to an electric shock or malfunction.
Keep away from the strange metallic materials not related to the unit and wiring works should be controlled by the electric expert engineer.
Else it may cause the unit to a fire, electric shock or malfunction.
If you don’t follow the directions, it could cause a personal injury, damage to the equipment or explosion
If you disobey the instructions, there may be possibility of personal injury, damage to equipment or
explosion. Please follow below Instructions.
Check the rated voltage and terminal array before wiring. Avoid the circumstances over 55℃of temperature. Avoid placing it directly in the
sunlight.
Avoid the place under circumstances over 85% of humidity.
Do not place Modules near by the inflammable material. Else it may cause a fire.
Do not permit any vibration approaching it directly.
Go through module specification carefully, ensure inputs, output connections are made with the specifications. Use standard cables for wiring.
Use Product under pollution degree 2 environment.
Before using the unit
*We appreciate you for purchasing CREVIS Products. To use the units more effectively, please read this quick guide and refer to
the respective user manual for further details.
Warning!
Caution!
* Power Isolators must be used according to the usage of 5VDC/24VDC/48VDC or AC Voltage modules

3. DIP S/W Setting Description
* ASCII mode is not available.
2. Communication and Power Cable Wiring
Notice for MAC ID(Station No.) Setting
1. set within the range of connectable Node number. (MAC ID No. 00 ~ 99)
2. When double setting Node no., Communication Error occurred.
2-2. Station No. Setting
x10
x1
2-1. Serial Cable Wiring
* Make sure System Power and Field Power must be
supplied via SMPS separately .
Item Item setup DIP Switch
#1 #2 #3 #4 #5 #6 #7 #8
Baud rate 1200 bps OFF OFF OFF
2400 bps ON OFF OFF
4800 bps OFF ON OFF
9600 bps ON ON OFF
19200 bps OFF OFF ON
38400 bps ON OFF ON
57600 bps OFF ON ON
115200 bps ON ON ON
Watchdog Disable Watchdog OFF
Enable Watchdog ON
Byte Format 8 bit, No Party, 1 Stop OFF OFF OFF
8 bit, Even Party, 1 Stop ON OFF OFF
8 bit, Odd Party, 1 Stop OFF ON OFF
8 bit, No Party, 2 Stop ON ON OFF
7 bit, No Party, 2 Stop* OFF OFF ON
7 bit, Even Party, 1 Stop* ON OFF ON
7 bit, Odd Party, 1 Stop* OFF ON ON
7 bit, No Party, 1 Stop* ON ON ON
RTU/ASCII
Mode RTU Mode OFF
ASCII Mode ON
* Specifications and designs may be changed without advance Notice.
RS232
CREVIS Co., Ltd
29-4, Gigok-ro, Giheung-gu, Yongin-si,
Gyeonggi-do, Korea 446-930
TEL : [phone] FAX : [phone]
Homepage : www.crevis.co.kr

4. Name of each part
3
4
5
6
Status LED Window
(Refer the Description)
Serial Connector
Serial Communication Connector
(Only use Manufacturer)
Hook for Mount on Din rail
1
Status LED Window Description
Switch for Station No. Setting
2 Removable Terminal Block
7 Dip S/W
Item LED is: State To indicate:
MOD :
Module
Status
LED
Off No Power No power is supplied to the unit.
Green Device Operational The unit is operating in normal condition.
Flashing Green Device in Standby The device needs commissioning due to configuration
missing, incomplete or incorrect.
Flashing Red
/Toggle MODBUS Error MODBUS error such as watchdog error, CRC/LRC error, Setup dip switch, error, etc.
Flashing Red Minor Fault Recoverable Fault
- EEPROM sum check error.
Red Unrecoverable Fault The device has an unrecoverable fault.
- Memory error or CPU watchdog error.
RXD :
Received
Data LED
Off Not Powered Device is not on-line or may not be powered
Flashing Green Adapter received correct
message frame
Adapter(Slave) received correct frame which address to
the slave or broadcast.
About 20msec flashing.
TXD :
Transmit
Data LED
Off Not Powered Device is idle or may not be powered
Flashing Green Adapter transmit frame Adapter(Slave) transmit frame.
About 20msec flashing.
I/O :
Expansion
Module
Status
LED
Off Not Powered
No Expansion Module Device has no expansion module or may not be powered
Flashing Green FnBus On-line,
Do not Exchanging I/O FnBus is normal but does not exchanging I/O data (Passed the expansion module configuration).
Green FnBus Connection,
Run Exchanging IO Exchanging I/O data
Flashing Red FnBus connection fault
during exchanging IO
One or more expansion module occurred in fault state.
- Changed expansion module configuration.
- FnBus communication failure.
Red Expansion Configuration
Failed
Failed to initialize expansion module
- Detected invalid expansion module ID.
- Overflowed Input/Output Size
- Too many expansion module
- Initial protocol failure
- Mismatch vendor code between adapter and expansion
module.
Field
Power
Status
LED
Off Not Supplied Field Power Not supplied 24Vdc field power
Green Supplied Field Power Supplied 24Vdc field power