CrossCore EZ-KIT Lite User manual
84-001970-01 Rev. 3.2
EZ-KIT Lite
Quick Start Guide
Thank you for purchasing this EZ-KIT Liteevaluation system. Before you begin to use your EZ-KIT
Lite, you must first perform the following procedure, which leads you through the software installation
and hardware setup.
For further information, please refer to the EZ-KIT Lite Evaluation System Manual on the CD-ROM.
Software Installation
1) Check the contents of your package and identify the following items:
•Installation Quick Reference Card for VisualDSP++ Development Environment
•VisualDSP++
development environment CD-ROM (CD includes the EZ-KIT Lite evaluation
system software)
•EZ-KIT Lite board
•Power supply
- 9V DC for ADSP-2181
- 7.5V DC for ADSP-2189 and SHARC DSPs
•RS-232 serial port 9-pin cable
•Registration form (to be filled out and returned to Analog Devices)
2) Ensure that your PC meets the following minimal requirements along with the requirements stated
in the Installation Quick Reference Card for VisualDSP++:
Windows® 98, ME, 2000, XP, or Windows NT
An available RS-232 port
3) Ensure that the VisualDSP++ Development Environment is installed.
a. If the latest version of VisualDSP++ is installed, insert the VisualDSP++ CD into CD-
ROM drive. Click on Install VisualDSP++. Click on Install Tools. On this prompt screen,
select Modify to add the EZ-KIT Lite software. On the next Component prompt screen
make your EZ-KIT Lite selection and begin install.
b. If VisualDSP++ is not installed please refer to the Installation Quick Reference Card for
VisualDSP++ Development Environment for further instructions. Perform only tasks 1
and 2. Continue after you have completed the VisualDSP++ install.
Important: Please note that installing the latest version of VisualDSP++ will completely replace
the older VisualDSP++versions on your computer, making them inoperable. If for some reason,
you need to use the older version you will need to uninstall this version and re-install the older
version.
Note: The VisualDSP++ serial number shipped with this EZ-KIT Lite evaluation system creates a
permanent license, but limits the software’s capability. For detailed information on these limitations
refer to the EZ-KIT Lite Restrictions section in the EZ-KIT Lite Evaluation System Manual.
www.BDTIC.com/ADI
EZ-KIT Lite, CROSSCORE , CROSSCORE Logo, Apex-ICE, Summit-ICE, VisualDSP++, VisualDSP++ logo, Blackfin and the Blackfin logo are all trademarks of Analog Devices Inc.
TigerSHARC, TigerSHARC logo, EZ-ICE, SHARC and the SHARC logo are registered trademark of Analog Devices Inc. All trademarks and logos are property of their respective holders.
Hardware Installation
4) Plug the power supply into a wall outlet and plug its connector into the power receptacle on the EZ-
KIT Lite board. Verify that the green LED (PWR/VCC) is lit.
5) Connect the RS-232 cable to your PC and to the EZ-KIT Lite board.
6) Run VisualDSP++ by holding down the keyboard’s Ctrl key while choosing Start -> Programs ->
VisualDSP -> VisualDSP++.
The Session List dialog box appears if you already have existing sessions. Skip to step 8 if
this is the first time running VisualDSP++.
7) Click on New Session.
8) In Debug target, choose EZ-KIT Lite (processor)and click OK.
ADSP-218x DSP Family Note: In Debug target, choose EZ-KIT Lite (ADSP-218x) and the ADSP-2189 or
ADSP-2181 processor and click OK.
9) Then Activate your session.
Now You’re Ready to use your EZ-KIT Lite.
Run the example programs to become familiar with the:
•EZ-KIT Lite evaluation system
•VisualDSP++ development environment
•DSP
These examples are located on your hard drive in the subdirectory: …VisualDSP\processor_family\EZ-
KITs\processor\Examples
You can also write, execute, and debug your own software. Refer to VisualDSP++ online Help, which
provides access to the Tools documentation (e.g., compiler, assembler). Read the VisualDSP++ User’s
Guide and the VisualDSP++ Getting Started Guide to learn about VisualDSP++.
For a detailed description of the EZ-KIT Lite board, refer to the EZ-KIT Lite Evaluation System Manual,
which is located in the …VisualDSP\Docs\ADSP-processor EZ-KIT subdirectory on your hard drive.
Limited Warranty
The EZ-KIT Lite evaluation board is warranted against defects in materials and workmanship for a
period of one year from the date of purchase from Analog Devices or from an authorized dealer.
www.BDTIC.com/ADI
Table of contents
