Crosswater Sontuoso US-N8ECS User manual

Installation Instructions
66-1/4"
13-3/4"
2" dia.
Weight - 155lbs
Weight with water - 506lbs
17-1/2"
22-3/4"
40-1/2"
2-1/4"
Tape
measure
Safety
glasses
Set
square
Pencil Spirit
level
Silicone
sealant
Tools required
2/3 Height = 42 Gal./159L
Installation notes
NOTES: The installation must comply with all plumbing codes including
local codes and be installed by a licensed plumbing contractor.
Store the bathtub in a safe place until you begin installation to avoid
any damage.
Assemble the bathtub on a mat to protect against damage to the
bathtub surface.
Avoid getting cement, grit, sand or masonry products on to the surface.
Protect and cover the bathtub during the installation period to
prevent damage from occurring.
Never use brown tape or gaffer tape directly on to the surface. If the
bath has to be repacked remember to avoid taping directly on to the
surface of the bathtub.
INSTALLATION: Remember to turn off the main water supply before
connecting to any existing pipe work or doing any maintenance.
WARNING! Please check for any hidden pipes and cables, electric
or otherwise before drilling holes in a wall or floor.
Dimensions
Introduction
This bathtub has been fully inspected throughout the production
process and only leaves our factory after a 15-step QC process.
Don’t remove the old fixture before you unpack and inspect the new
bathtub.
Carefully remove the bathtub from the box, taking care the bathtub is
carried in the bag and check that all parts have been supplied.
Before beginning installation of the bathtub please check for any
damage that may have occurred during transport. Note: Damage
claims cannot be made during or after installation.
Improper installation shall result in loss of warranty in case of damage
caused by impacts or rubbing against rough surfaces.
Prior to installing the bathtub prepare a connection of water inlet/outlet.
Pay attention to leveling of floor where the bathtub will be located,
ensuring it can take the weight of the bathtub, water and bather(s).
The customer may choose the type and location of the faucets,
installation instructions should be supplied by the faucet manufacturer.
The installation procedure of the bathtub may differ from that
described in the installation instructions, depending on where you
wish the bathtub to be located.
Wet surface of the bathtub may create a risk of slipping which may
increase by using soap, shampoo, oils and similar products.
IMPORTANT: Please read these instructions carefully before you
begin and retain for future reference.
We do not accept responsibility for any problems that may occur
through incorrect installation.
RECOMMENDATIONS:
It is recommended that walls and floor are fully tiled and finished
before installation, this ensures that the product is installed flat to the
tile face and allows product to be easily removed if required in the
future.
It is recommended to remove the protective packaging after
installation of the bathtub.
It is recommended to only fill the bathtub with water up to 2/3 of
its height.
It is recommended to use US-CW12 and ITD5135 waste flow
products with this bathtub.
Sontuoso Bathtub
US-N8ECS
27-1/2"

Issue date: 220616
Warranty - All Crosswater London products come with a limited lifetime warranty. For full details, terms and conditions visit our website.
For further information contact:Crosswater London 393 Fortune Blvd., Milford, MA 01757
Toll free number: 844-XWATER-1 (844-992-8371) tel: [phone] fax: [phone]
www.crosswaterlondon.com
email: [e-mail]
x4
Once installed and sealed, DO NOT
use or get wet for 24 hours.
Installation
Maintenance
lThis installation guide does not include details of
waste connection; final decision about
installation of waste connection should be made
by a licensed plumber.
lInstall the waste according to the installation
instructions supplied with the waste.
WARNING: Do NOT overtighten the waste as this
may cause long term damage to the bath.
We recommend to use a torque wrench to tighten
the waste by using a torque force between
25Nm or 18.5 ft/lb and 50Nm or 36.8 ft/lb.
IMPORTANT:
This bathtub is heavy and installation requires 2 people.
Crosswater London cannot accept responsibility for any injuries
caused to those attempting to install this bathtub without
adequate and appropriate tools or resources.
l Remove the bathtub from the packaging using the bag with
handles.
l Use the bag with handles to lift and move the bathtub.
l Do not drag the bathtub over rough surfaces or sharp
objects. Lift and place the bathtub into position.
lDo not drop the bathtub!
l Check that the wedges have been supplied.
Installation - carriage
lPlace the 4 wedges in position. lOnce sealed, the wedges can be
disposed of.
Cleaning and maintenance of the product
•The product should be cleaned with a moist cloth with a
small quantity of a non-abrasive cleaning agent, eg.
dishwashing detergent. In case of any stains on the
surface of the product it is recommended to remove
them immediately.
•NOTE: Hair dyes and other ‘color’ cosmetics, (such as
mascara, lipstick, face powder etc.), may leave slight
discoloration if not removed immediately.
•Water temperature should not exceed 49°C/120°F
•If chemicals such as soda lye, strong solvents such as acetone,
methanol, methylene chloride, etc. come into contact with the
bath, rinse with warm water immediately.
•In case of small scratches it is possible to purchase a repair kit
(US-CRK). In order to remove the scratches, please read the
instructions included in the kit.
•Do not allow limescale to deposit on the surface (from hard
water). Such stains can be removed with dissolved vinegar or a
good quality limescale removing agent, generally available and
indicated for this purpose.