Crosswater US-WF FSBATH User manual

Installation Instructions
Weight - 236lbs
Weight with water - 779lbs
Tape
measure
Safety
glasses
Set
square
Pencil Spirit
level
Silicone
sealant
Weight - lbs
Weight with water - 7 lbs
Tools required
2/3 Height = 5 Gal./2 L
Installation notes
NOTES: The installation must comply with all plumbing codes including
local codes and be installed by a licensed plumbing contractor.
Store the bath tub in a safe place until you begin installation to avoid
any damage.
Assemble the bath tub on a mat to protect against damage to the
bath tub surface.
Avoid getting cement, grit, sand or masonry products on to the surface.
Protect and cover the bath tub during installation, other tradesmen
might damage the bath if no precautions are taken.
connecting to any existing pipe work or doing any maintenance.
WARNING! Please check for any hidden pipes and cables, electric
Dimensions
Introduction
This bath tub has been fully inspected throughout the production
process and only leaves our factory after a 15 stage QC process.
Carefully remove the bath tub from the box, using the carrying bag
and check that all parts have been supplied.
Before beginning installation of the bath tub please check for any
damage that may have occurred during transport.
Improper installation shall result in loss of warranty in case of damage
caused by impacts or rubbing against rough surfaces.
Prior to installing the bath tub prepare a connection of water inlet/outlet.
ensuring it can take the weight of the bath tub and water.
The customer may choose the type and location of the faucets,
installation instructions should be supplied by the faucet manufacturer.
The installation procedure of the bathtub may di
described in the installation instructions, depending on where you
wish the bath tub to be located.
IMPORTANT: Please read these instructions carefully before you
begin and retain for future reference.
We do not accept responsibility for any problems that may occur
through incorrect installation.
RECOMMENDATIONS:
It is r
installa
and allows product to be easily removed if required in the future.
It is recommended to remove the protective packaging after
installation of the bath tub.
its height.
Waldorf Freestanding
Bath Tub
US-WF_FSBATH
It is required to use US-CW15 waste ow products with this
bath tub.
If the surface of the bath tub is wet it may create a risk of slipping
which may increase by using soap, shampoo, oils and similar products.
Do not remove the old xture before you unpack and inspect the
new bath tub.
INSTALLATION: Remember to turn o the water supply before
Pay attention to leveling of oor where the bath tub will be located,
19 11/16”
3 35/64”
17 23/32”
45 43/64”
3 15/16”
23 5/8”
Ø2 3/32”
47 9/32”
65 17/32”
20 5/32” 31 3/8”

Issue date: 220616
Warranty; All Crosswater products come with a limited lifetime warranty. For full details, terms and conditions visit our website.
For further information contact; Crosswater London, 393 Fortune Blvd., Milford, MA 01757
Toll free number: 844-XWATER-1 (844-992-8371) tel: [phone] fax: [phone]
x4
Once installed and sealed, DO NOT
use or get wet for 24 hours.
Installation
Maintenance
lThis installation guide does not include details of
of waste connection should be taken by a suitably
lInstall the waste according to the installation
instructions supplied with the waste.
WARNING: Do NOT overtighten the waste as this
may cause long term damage to the bath.
We recommend to use a torque wrench to tighten
the waste by using a torque force between
25Nm or 18.5 ft/lb and 50Nm or 36.8 ft/lb.
Cleaning and maintenance of the product
lClean with water or a soft detergent and dry with a soft cloth.
Do not use detergents containing hydrochloric acid or caustic or
abrasive materials, chemicals or cloths.
Everyday cleaning
lWe recommend a non-abrasive bathroom cleaner.
Warning
l
toilet bowl cleaning as they may damage your bath.
NOTE: Hair dyes and other ‘color’ cosmetics, (such as mascara,
lipstick, face powder etc.), may leave slight discoloration if not
removed immediately.
lDo not allow lime scale to deposit on the surface (from hard water).
Such stains can be removed with dissolved vinegar or a good
quality limescale removing agent, generally available and indicated
for this purpose.
IMPORTANT:
This bathtub is heavy and installation requires 2 people.
Crosswater cannot accept responsibility for any injuries caused
to those attempting to install this bath tub without adequate and
appropriate tools or resources.
l Remove the bath tub from the packaging using the bag with handles.
l Use the bag with handles to lift and move the bath tub.
l Do not drag the bath tub over rough surfaces or sharp objects.
Lift and place the bath tub into position.
lDo not drop the bath tub!
l Check that the wedges have been supplied.
Installation - carriage
lPlace the 4 wedges in position. lOnce sealed, the wedges can be
disposed of.
www.crosswaterlondon.com
email: [e-mail]