Crown FD-40MC User manual
16 INCH STAND FAN
FD-40MC
INSTRU TION MANUAL
C
AC 220-240V 50Hz 50W
SAFETY PRECAUTIONS
When using any electrical appliance,basic safety precautions should always be
followed,including the following:
1. Read all instructions and keep for future reference.
2. This appliance is not intended for use by persons(including children) with reduced
physical,sensory or mental apabilities, or lack of experience and knowledge,unless
they have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety.
3. Young children should be supervised to ensure that they do not play with the
appliance.
4. Always unplug the appliance from the mains when not in use .
5. To disconnect the appliance,switch the control to OFF,then unplug from the mains.
6. To unplug the appliance,always grasp the plug;do not pull the cord.
7. If the supply cord is damaged it must bereplaced by the manufactuer, its service agent or a
similarly qualified person in order to avoid a hazard.
8. Do not use outdoors. This appliance is designed for household use only.
9. Place the power cable away from areas where people walk so that it cannot be
stepped on or tripped over.
10. Always use the appliance on a flat ,stable surface.
11.Never clean this appliance when it is plugged in .Do not immerse it in water, Clean the
outside surface with a damp cloth or soft brush and dry with a soft dry cloth.
12.Use the appliance only as directed in this manual. Misuse could void your warranty.
13. Avoid contact with moving parts, Never insert any objects through the grille when the fan
is in operation
ASSEMBLY INSTRUCTION:
Base Assembly
1.Unscrew the Fasten Ring and Base Locking
Nut from the Stand Assembly.
2. Insert the Stand Assembly through the hole in
the center of the Base and twist into position.
3. Turn the Stand Base upside down with the Stand
Assembly facing the floor and place the Base
Weight Support to the bottom of the Base.
Tighten the Base Weight Support to the Stand
Base by screwing back the Ring and
Base Locking Screw
F1. ger
2. your desired height and lock in place by tightening the
3
tor to the Telescopic inner by tightening back to Thread
Bolt with the Locking Knob.
1.
the Motor Housing .Make sure the Rear Grill fits securely
2.
3 he Fan Blade onto the Motor Shaft by tightening the blade screw to the Motor
4.
ll
an Head Assembly
There are two knobs at the connector; the smaller one is the Tilt Knob and the big
one is the Locking Knob. Unscrew the Locking Knob to loosen the Thread Bolt.
Pull Telescopic inner up to
Height Adjustment Screw
.Place the Fan Head onto the Telescopic inner. Align the holes on the connect and the
Telescopic inner Install the mo
Final Assembly
Position the Rear Grill over the Motor Shaft, making certain the 2 notches at the Rear
Grill fit over the 2 prongs on
against the Motor Housing.
.Secure the Rear Grill to the Motor Housing with the four Rear Grill Locking Screws
Loosen the grill locking screw at the bottom of the Rear Grill and save it.
. Install t
Shaft.
Centre the Front Grill by aligning the logo on the grill Hub so it is horizontal and parallel
to the floor. Then secure the Front and Rear Grills completely together by snapping gri
clips into place. Lastly, tighten the grill locking screw at the bottom of the Rear Grill.
5. Place the Control box on
Box Holder by Screw
the holes of the Telescopic Inner ,then fix it with the Control
REMOTE CONTROL
aximum distance for transmitting
r local regulations.
ntrol for a longer period(4 weeks or more),take
1. Put two batteries (TypeAAA,1.5V) into the battery compartment of the remote control
and close the cover until it clicks into place. The m
signals from the remote control to the fan is 6 meters. Make sure that no objects are
hindering signal transmission.
2. Take the protective film off the remote control.
and after replacing the old batteries dispose of
3. Use only batteries of TypeAAA,1.5V
them for recycling and according to you
4. If you do not wish to use the remote co
the batteries out of the remote control.
OPERATING INSTRUCTIONS
Ensure voltage used corresponds with the voltage indicated.
b) Use the remote control to select the speed.
c) Tilting angles-By pushing the tilt-guard, you can adjust the fan to your desired elevation.
hey must be
C
d) Never touch the blades with hand or any object!
e) Do not pull the cord grip the plug itself. If the cord or plug get damaged, T
checked by a qualified repairer before further use.
LEANING AND MAINTENANCE INSTRUCTIONS:
To clean:Disconnect the power cord from the mains. Remove the guard and the blades
carefully. Do not drop the blades! First use soft cloth with light soap to clean off oil stains.
Then wipe and polish with dry cloth. Never use polish or any corrosive liquid that will
damage the paint, metal or plastic! Put back the blades and lock the guard securely before use.
WARNING: Unplug from electrical supply source before cleaning. After servicing, any
safety device (including grilles and blades)must be reinstal ed or remounted as previously installed.
Use soft damp cloth then wipe with dry cloth. Do not use harmful cleaners. Do not bend the
blades.
FD-0MC
:
.
.
.
.
.
.
..
.
.
.
.
1.5VAAA
.6..
.
1.5VAAA
.
.
.
.
.
:
.
.
.
Table of contents
Other Crown Fan manuals
Popular Fan manuals by other brands
Fanimation
Fanimation Inlet FPS7880SN owner's manual
Carrier
Carrier NO FOUND 09FA installation instructions
Airflow
Airflow iCON PCS quick start guide
Broan
Broan NUTONE QT series installation guide
Modern Forms
Modern Forms FR-W2202-62L-SB/MB installation instructions
Plymovent
Plymovent FUA-1300 user manual
