Crystal Video PRO Z User manual

二C匡
CRYSTA
L VIDEO
PROZ
Zero Latency Channel Scan
Wireless Video nsmission System
翌一
^3

Important Information
公
丛
心

切」山zou
Contents
.
一
01

*
a
P
02
I
_
°
°
°
°
03

Structure & Interface
Transmitter: 7118
04
C棒
TX
Transmitter Interface Description
I
_
05

Receiver: 3118
C呵 J
尸尺口.z
丿
06
RX
,一
,一
,-1
_
07

Mounting
For transmitter 7118
�
1
二
厂
1工
08 09

仁'�
I_
_
_
_
矗t.v
付
贮贮
勹
V
For receiver 3118
°
10 11

1
工
厂�
工
Camera Battery
,
12V Power
Adapter
SDI OUT
SDI OUT
HDMI OUT
12 13

1. The transmitter can be powered with the following methods:
』
14
15

2. The receiver can be powered with the following methods:
16
17

Ba
18
6.5V
CH
Batt
6.
OVIDEO
CH
I
19

-Channel Switching Operation
Transmitter's Menu Button:
20
Receiver's Menu Button:
V
I
[ I �
--
\
21

-Precautions
Installation Height and Distance
Channel Settings
Mounting:
°
"
23

HDMI/SDI Connection and Antenna Installation
Recommendations
Battery Endurance
24
- Troubleshooting

FCC Warning
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this
device must accept any inte rference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interferenceto radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
· Reorient or relocate the receiving antenna.
· Increase the separation between the equipment and receiver.
· Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
· Consult the dealer or an experienced radio/TV technician for help.
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum
distance 20cm between the radiator and your body.
This manual suits for next models
2
Table of contents
Other Crystal Video Microphone System manuals
Popular Microphone System manuals by other brands

Shure
Shure AMS4000 Installer manual

Sennheiser
Sennheiser EM 300 G3 Product sheet

Veeder-Root
Veeder-Root TLS-RF Series Site Prep and Installation Manual

SEIKAKU
SEIKAKU Show UEM-8DR SERIES user manual

Louroe Electronics
Louroe Electronics ASK-4 #401 Installation and operating instructions

Chiayo
Chiayo R-1001 operating manual

Piezotronics
Piezotronics 378C10 Installation and operating manual

Conrad
Conrad 75 17 47 operating instructions

brevini
brevini High Power Series manual

Behringer
Behringer ULTRALINK UL2000B user manual

VocoPro
VocoPro UHF-5900 owner's manual

Telex Communications
Telex Communications Electro-Voice R200 Series owner's manual