Crystal Inspire 104 User manual

Inspire Model
104/206/308/414
User Guide
be
a
n
t
a
U
bl
e
I
n
n
o
va
t
io
n
&
D
ev
e
lo
p
m
e
n
t
1 9 8 21 9 8 2
Since Since
Be Vocal
For Local
QR for Inspire User Manuals

Inspire 104/206/308/414 User Guide
PRODUCT VIEW
104
• 1 Trunk
• 4 Extension
Inspire 104
Inspire 308
308
• 3 Trunk
• 8 Extension
LED
Display
414
• 4 Trunk
• 14 Extension
Inspire 414
Inspire 206
206
• 2 Trunk
• 6 Extension
System Features subject to change owing to constant innovations in technology without prior notice.

S.No. Function Page No.
General Information. 2
Function Summary 3
1 Intercom Call 4
2 Trunk / JN Call 4
3 Last No. Redial 4
4 Answer/ Receive Call 4
5 Call Hold and Retrieve 4
6 Call Consult 4
7 Call pickup 5
8 Call Transfer 5
9 CLI 6
10 Auto call Back (extn / jn) 6
11 Do not Disturb / Cancel 6
12 Call Forward / Cancel 6
13 Barge in 6
14 Call toggle 7
15 Monitor 7
16 Conference 7
17 Day/Night Mode 7
18 Flash Time 7
19 Dynamic Lock/ Open 8
20 Hot line (Extn./Jn.) 8
21 Hot line Fun./cancel 8
22 Alarm 8
23 Relay 9
24 Paging 9
25 Trunk Reservation 9
26 Emergency Dial at FND 9
27 FND Connectivity 10
28 Global Dial 1 0
29 Remote Maintenance 1 0
General Functional Information 11
General Installation Information 12
Warranty 1 3
User Guide Contents
Inspire 104/206/308/414 User Guide 1

Model Extension Dial No. Trunk Access No.
104 21,22,23,24 61 or 0/*5
206 21,22,23,24,25,26 61,62 or 0/*5
308 21,22,23,24,25,26,27, 28 61,62,63 or 0/*5
414 21,22,23,24,25,26,27, 28..........34 61,62,63,64 or 0/*5
Default Extension Dial No/ Trunk Access No.
Sr. No. Features 414 308 206 104
1. KTS Connectivity (optional) YES YES NO NO
2. FSK CLI (Caller ID)(optional) YES YES YES YES
3. Relay & Paging (optional) YES YES NO NO
4. Voice DID (optional) YES YES NO NO
5. MMOH (optional) YES YES NO NO
6. FND Display (optional) YES YES NO NO
7. KTS interface (2 Port) Compulsory to install with KTS set
8. FND interface Compulsory to install with FND
Special Remarks for value added optional functions with products / cards
Note :- (1) Optional FSK CLI support only 2 trunk port (Line 1 & Line 2) with 414 model
(2) Required optional extra card / products on additional cost to use function of
KTS, FSK, Relay & Paging, DID, MMOH and FND.
(3) 308/414 Model only support timer function like alarm, auto day night,.............etc.
(4) Either KTS or FND can install at a time .
Inspire 104/206/308/414 User Guide
General Information
Model PFTT extension no.
104 Extn 21 for line 1
206 Extn 21 for line 1, Extn 22 for line 2
308 Extn 21 for line 1, Extn 22 for line 2, Extn 23 for line 3
414 Extn 21 for line 1, Extn 22 for line 2, Extn 23 for line 3, Extn 24 for line 4
Power Failure Trunk Transfer : Trunk line Directly Connect with pre-assigned extension no. in case of power
failure / shut down / switch off the system
2
?Date & time Display
?Room No. / Extn. No. Display
?Room Buzzer Alert No. Display
?Room call Buzzer waiting flash
?Call waiting flash clear option
Optional for 308 / 414
Note :- FND Interface card compulsory to install with FND
FND
LCD Display 2 line
Caller -ID
H/F Speaker Phone
Digital Volume Control
Tri Colour LED - Extn / Trunk / Busy
Keys with
Tri Colour LED
KX - 30
KTS
28 (14+14) Programmable
and 13 Function Key
Note :- KTS Interface card compulsory to install with KTS

Remark: - Pl refer to programming / user section to activate these function's
Caution: - All System Programming can be done only in Main Password mode from any Extn. in
tone / DTMF mode at the site.
Function Summary
No. Function User code Flexible plan Remark
1 Intercom Call 21,22,23,24,25,26.......34 Yes (1 to 3 digit)
2 Junction No. Access 61,62,63,64 or 0/*5 Yes (1 to 3 digit) System Program
3 Last No. Redial Dial # No
4 Answer/ Receive Call See User Function
5 Call Hold & Retrieve See User Function
6 Call Consult See User Function
7A Call pickup *4 Yes
7B Selective call pickup *76+extn.no. Yes
8 Call transfer Flash + Extn. No. No
9 NoCLI See User Function
10 Auto call Back(extn/jn) Dial 75 No
11 Do not Disturb *721+Self Extn. No. Yes User Program
DND cancel *720 Yes
12 Call Forward *721+Extn. No. Yes
Call Forward cancel *720 Yes
13 Barge in Dial 83 No System Program
14 Call toggle Flash + 1 No
15 Monitor Dial 80 No System Program
16 Conference (3 Party) Flash + 0 No System Program
17 Day/Night Mode *85+1/2/3 (Day/Night/Auto ) Yes System / User Program
18 Flash Time See User Function
19A Dynamic Lock *81+ self PW Yes System / User Program
B Dynamic Lock OPEN *82+ self PW Yes
C Dynamic Lock PW change *86+Old PW+New PW Yes
20 Hot line (Extn./Jn.) *16+1+ Extn / Jn Yes System / User Program
21 Hot line Fun./cancel *16+0 Yes
22 Alarm *98+ 2 (one time) /3,4,5 (repeat) Yes User Program
23 Relay Port *16+ 5 (On) / 6 (Off) / 7 (click) Yes System Program
24 Paging *87+1 Yes System / User
Program
25 Trunk Reservation *112 Yes System Program
26 Emergency dial *99 Yes System Program
27 FND Access 21/22/23/24
28 Global Dial *88 + 00 to 99 Yes System Program
Inspire 104/206/308/414 User Guide 3

(6) CALL CONSULT : After put on hold existing caller, you can make another internal call to consult & reply back
after retrieve. During consult total secrecy maintained for the call. Use following procedure :
Step Procedure Tones Abbreviations
1 Hold the existing caller Music tone to hold caller
2 Dial other extension number Ring tone
3 Reply by other party, consult with him
4 Use flash + 1 again to retrieve hold caller
Step Procedure Tones Abbreviations
1 Lift handset Internal Dial Tone
2 Dial desired extension number Ring Back Tone Extn. No. is 21,22,23,24...................34
3 Start talking when other extension answers
4 Hang up when conversation is over
v"If you get busy tone ( i.e. the dialed extn is busy ), hang up & try again later or use the
"Auto Call Back" function.
(1) INTERCOM Call (Extension to Extension) : To make an internal call
(2) TRUNK / JN CALL (Junction no. Access) : To make an outside call
Step Procedure Tones Abbreviations
1 Lift handset Internal Dial Tone
2 Dial trunk access code Trunk Line Tone Access code 61/62/63/64 or 0/*5
3 Dial desired outside number Ring Back Tone
4 Start talking when called party answers
5 Hang up when conversation is over
v"If you get busy tone after dialing JN access code, hang up & try again later or use the "Auto
Call Back" function.
vIn default mode all Jn. Lines are programed in 0/*5 group as rotational access.
Step Procedure Tones Abbreviations
1 Lift handset Internal Dial Tone
2 Dial # Redial last dialed external number
vDo not use "REDIAL" key of your phone to redial the last dialed external number.
(3) LAST NO. REDIAL : To redial last external dialed out number
(4) ANSWERING / RECEIVING CALLS : To answer a call
Step Procedure Tones Abbreviations
1 Extension ringing Ring Tone
2 Lift handset
3 Start conversation
4 Hang up when conversation is over
(5) CALL HOLD & RETRIEVE : To hold during conversation with trunk / Internal call, use following procedure.
Step Procedure Tones Abbreviations
1 While talking with caller ( trunk / Internal )
2 Press flash key or flash hook switch beep beep Tone Music tone to hold caller
3 Flash again to retrieve hold caller
Inspire 104/206/308/414 User Guide 4

Step Procedure Tones Abbreviations
1 Lift handset Internal Dial Tone
2 Dial *4 to connect to calling extension
3 Start talking
4 Hang up when conversation is over
(7) CALL PICK UP :
(A) COMMON (INTERCOM CALL / TRUNK CALL) : An extension can pick-up any ringing extension, To do so:
vSimultaneous & Auto call back Ring on an extension cannot be picked by any other extension.
vFirst Priority is always given to incoming call ring.
Step Procedure Tones Abbreviations
1 Lift handset Internal Dial Tone
2 Dial *76 + XX XX=Ringing Extension number
3 Start talking
4 Hang up when conversation is over
(B) SELECTIVE (INTERCOM CALL / TRUNK CALL) : To do so.
(8) CALL TRANSFER : You can transfer a call either after conversation with 2nd extn. or without consult (blind).
to do so:
(A) CALL TRANSFER WITH FLASH (INTERCOM CALL \ JUNCTION CALL):
Step Procedure Tones Abbreviations
1 While talking with caller
2 Press the Flash Key, or Flash the HS Beep-beep tone HS=Hook switch
3 Dial Extension number Ring Tone
4 A When other party answers, consult the call
with him & hang up to transfer the Call.
OR
4 B Hang up before other party answer's.
Call will connect automatically as
soon as extn answer's.
vIf by mistake you dial the wrong extension number or the dialed extn is busy / goes
noreply,press the Flashkey to reconnect back with the external caller.
vTo revert back to the call on hold after conversation with any extn., press Flash +1.
vIf the transferred call is not answered with- in 30 sec., it shall automatically disconnect.
v This Feature work only with default extension no.
(B) CALL TRANSFER WITHOUT FLASH (INTERCOM CALL OR JUNCTION CALL):
Step Procedure Tones Abbreviations
1 Speech with caller Ring Tone
2 During Conversation, dial Extension number
3 A When other party answers, consult the
call with him & hang up to transfer the Call.
OR
3 B Hang up before other party answer's .
Call will connect automatically as
soon as extn answer's.
Inspire 104/206/308/414 User Guide 5

Cancellation of DND Lift handset & Dial *720, Get confirmation tone
(11) DO NOT DISTURB (DND) : If you do not want to receive any calls ,you can enable this feature.To do so:
Step Procedure Tones Abbreviations
1 Lift handset Internal Dial Tone
2 Dial *721 + xx, Confirmation Tone XX = Self Extension number
3 Hang up,
Now if any other extension calls your extension, he will get error tone
Note:A broken dial tone is always heard on the extension with this feature enabled. However you can
make outgoing calls normally from this extn.
(12) CALL FORWARD :You can forward all calls to any other extension. This is use ful when you are move to some
other extension and do not want unattended your calls. To do so:
Now anyone dialing your number shall be connected to this forwarded extension.
Note: A broken dial tone is always heard on the extension with this feature enabled. However
you can make outgoing calls normally from this extn.
Cancellation of Call Forward Lift handset & Dial *720, Get confirmation tone
(13) BARGE-IN(WITH WARNING TONE) : With this facility you can convey priority message to a busy extension.
To do so:
Step Procedure Tones Abbreviations
1 Lift handseat Internal Dial Tone
2 Dial desired Extension- If busy Busy Tone Busy with intercom or trunk call
3 On Busy tone dial 83 Warning tone to All 2 sec Beep Beep tone before intercept
4 Start conversation
vBarge-in shall not work if the busy extension is in Dialing / Ringing / Conference mode.
(9) CLI (DTMF/FSK SIGNAL) : If you have a caller ID Telephone set, you can avail below three features:
A) Calling extension number display.
B) Caller ID number of incoming call (Round Robin / Simultaneous).
C) Caller ID number of transferred call (Incoming / outgoing)
Step Procedure Tones Abbreviations
1 Lift the handset Internal Dial Tone
2 Dial *721 + xx, Confirmation Tone XX = Extn. No., where calls forwarded
3 Hang up,
Step Procedure Tones Abbreviations
1 Lift the handset Internal Dial Tone
2 Dial desired junction/Extn. Number Busy tone
3 During Busy tone Dial 75 Confirmation Tone
4 Hang up
(10) AUTO CALL BACK ON BUSY : If the dialed junction/extn. is busy, you need not try it again and again. By using
this feature the system will automatically call you when the phone becomes
free. Lift the phone for dialing. To do so.
Inspire 104/206/308/414 User Guide 6

Step Procedure Tones Abbreviations
1 Hold the existing caller Music tone to hold caller
2 Dial other extension number Ring tone
3 Reply by other party, consult with him
4 Now Press Flash + Dial 1 for Call Toggle Music tone to hold caller
5 Repeat Step 4 to toggle between both Party
6 Hangup, when conversation is over
(14) CALL TOGGLE : You can toggle between your current call (Intercom / JN) & a 2nd call on hold.
Step Procedure Tones Abbreviations
1 Lift handset Internal Dial Tone
2 Dial desired Extension- If busy Busy Tone Busy with intercom or trunk call
3 On Busy tone dial 80 No Warning tone Now can monitor the call (after 1 sec)
4 Hang up
(15) MONITOR : With this facility you can monitor conversation of two extensions without any indication
(short beeps) to busy extn
1) All three intercom, 2)Two intercom& one JN call, 3) Two JN call & one intercom
(16) CONFERENCE (THREE PARTY) : You can make conference among yourself & other two (either extn. or Jn.).
Proceed as below with different options
When the master extension which had originated conference goes On-Hook, conference will be terminated.
NOTE : While adding extensions/ junction., you may get
A) Busy Tone - Dial Flash + 2 and re-start the process.
B) Error Tone - Dial Flash + 2 and re-start the process.
C) No-Reply - Dial Flash + 2 and re-start the process.
Step Procedure Tones Abbreviations
1 In speech with Extn/Jn
2 Press F (Flash) Key, to put On hold Music tone Music tone to hold caller
3 Dial 2nd Extension / Jn number
4 When extension answer's,
Press Flash Key & Dial " 0 "
5 Three party conference is established
6 Hang up, whenconversation is over
(17) DAY/NIGHT MODE : To set for day / night / auto, landing mode for incoming call
Step Procedure Tones Abbreviations
1 Lift handset Internal Dial Tone
2 Dial *85 + 1/2 for Manual D/N mode Confirmation tone 1= day (D) & 2= night (N) mode
OR
Dial *85 + 3 for Auto D/N mode Confirmation tone
3 Hang up
(18) FLASH TIME : Flash time duration setting of the extension need to program, if flash not responding
properly to operate different user function. Default time set for 600ms of all extension.
To change the flash time, please consult with dealer / installer.
Inspire 104/206/308/414 User Guide 7

(19) DYNAMIC LOCK : An extension can use dynamic lock to protect misuse of outgoing trunk call's from
his extn. To do so:
(A) TO SET DYNAMIC LOCK
Step Procedure Tones Abbreviations
1 Lift handset Internal Dial Tone
2 Dial *81 + self password (xxxx) confirmation tone Default XXXX is 1111
3 Hang up
(B) TO OPEN DYNAMIC LOCK
Step Procedure Tones Abbreviations
1 Lift handset Internal Dial Tone
2 Dial *82 + self password (xxxx) Confirmation tone Default XXXX is 1111
3 Hang up
(C) TO CHANGE SELF PASSWORD
Dial *86 + XXXX + ZZZZ XXXX = Old self password ZZZZ = New self Password
(20) HOTLINE EXTN. / JN.: You can use hotline, when a particular extension/jn is to be used repeatedly.To do so
Step Procedure Tones Abbreviations
1 Lift Hand set Internal Dial Tone
2 Dial *161 + XX Confirmation Tone XX = Extension Number /Junction no.
Note- Refer programming manual to set delay timer for HOTLINE. Default time is 3 Sec.
Cancellation of Hotline Lift handset & Dial *160,Get confirmation tone
(21) HOTLINE FUNCTION:
Step Procedure Tones Abbreviations
1 Lift hand set Internal Dial Tone
2 Wait for automatic dial of extn / Jn number Ring back/ Jn tone
3 Start talking when set extension answers
or dial outside no. after Jn. Dial tone
4 Hang up, when conversation is over
(22) ALARM :
Step Procedure Tones Abbreviations
1 Lift handset Internal Dial Tone
A One Time Alarm (ring at specified time)
Dial *982+HHMM Confirmation tone HHMM = 24 Hr format
B Repeat Alarm (ring daily at specified time) Confirmation tone X = 3 1ST Alarm,4 2ND Alarm,
Dial *98+ X+HHMM 5 3rd Alarm
Note :- Your extension shall now ring daily at this time specified time till it is not cancelled.
To cancel all alarm's Dial *980
Inspire 104/206/308/414 User Guide 8

(23) RELAY PORT : The relay port can be used manually or set for pre-programmed timings to switch on/off any
electrical appliance.
Caution: - If the electrical appliance consumes less than 0.5 amp. of current (i.e. - 100 watt ) ,you can drive it
directly, and if it consumes more, you can drive it through an external relay/contactor.
Note : To set for auto operation of the relay, pl refer to the programming section.
(A) MANUAL OPERATION : To operate any electric gadget
Step Procedure Tones Abbreviations
1 Lift handset Internal Dial Tone
2 Dial *165 for relay ON Confirmation tone
3 Dial *166 for relay OFF Confirmation tone
4 Hang up
(B) CLICK OPERATION : To operate any electronic door lock
Step Procedure Tones Abbreviations
1 Lift handset Internal Dial Tone
2 Dial *167 for relay click Confirmation tone
3 Hang up
(24) PAGING : Audio Amplifier of public address system can be connected to the paging port
(optional attachment required ). You can make an announcement directly as follows
Step Procedure Tones Abbreviations
1 Lift handset Internal Dial Tone
2 Dial *87+X Confirmation tone X = 1 active paging function
(25) TRUNK RESERVATION :You can reserve the particular trunk line for pre-defiend time to make outgoing
calls. To do so:
Step Procedure Tones Abbreviations
1 Lift the handset Internal Dial Tone
2 Dial *112 + X (Trunk No.) Confirmation Tone X =Trunk No., 1/2/3/4
i.e. line 61/62/63/64
3 Hang up
Cancellation of Trunk Reservation Lift handset & Dial *1120, Get confirmation tone
Inspire 104/206/308/414 User Guide 9
(26) EMERGENCY DIAL AT FND : Any extension can dial emergency code. Now display will show intercom
extension no.with buzzer beep. Normally FND show date / time in ideal
condition. Use following procedure:
Step Procedure Tones Abbreviations
1 Lift the handset Internal Dial Tone
2 Dial *99 Ring Back Tone Show extn. no. & buzzer beep at FND
Now you can attend directly to emergency caller .
To cancel of FND status Dial *77+Self Extension No.
Note :- To set for click action timer, please refer programming manual.
Note :- To set for reservation timer, Please refer programming manual.

(27) FND ACCESS : You can install max. 4 no. FND (Front no. Display ) with inspire 308 & 414 model EPABX to
see Intercom number. When any extension dial particular number of display, it will show caller
no. as well as buzzer beep for ten sec.
Step Procedure Tones Abbreviations
1 Lift the handset Internal Dial Tone
2 Dial 21 Ring Back Tone Show extn. no. & buzzer beep at 1st FND
OR
3 Dial 22 Ring Back Tone Show extn. no. & buzzer beep at 2nd FND
OR
4 Dial 23 Ring Back Tone Show extn. no. & buzzer beep at 3th FND
OR
5 Dial 24 Ring Back Tone Show extn. no. & buzzer beep at 4th FND
Inspire 104/206/308/414 User Guide 10
(29) REMOTE MAINTENANCE : Easy way to program the system as per need of user from the remote location.
Service engineer can program over phone line without presence at user place .
Use below procedure for remote program:
(1) Establish a call ( Via incoming / outgoing) with user through trunk line &
start conversation at any extension.
(2) User will put service engg. on hold by hook flash -- Get music tone on hold
(3) After hook flash dial *399 by user. Now both will be come back on
conversation mode
(4) Now any one can dial system password to do programing and get
beep beep tone.
(5) Start programing by service engg.
(6) Get assurance tone on each correct program other wise get error tone
(7) Continue the program after each correct steps.
(8) To exit from programing mode dial 0
Note :- (1) Programing can be done only in DTMF mode.
(2) The service engg. and user at extension can talk during the remote programing
Step Procedure Tones Abbreviations
1 Lift handset Internal Dial Tone
2 Dial any one memory location Particular memory location will be
*8800 to *8899 dialed out
Note :- Refer programming manual to set Global Memory Location.
(28) GLOBAL MEMORY DIALING : 100 no of Central Memory Pool (*8800 to *8899) for external call can be
commonly accessed by all extensions. Each stored no. can be max. 16 di gits
(including STD/ISD codes and external no.)

TRUNK ( INCOMING / OUTGOING ) : DEFAULT STATUS
Model
Incoming Call (Day/Night Mode)
Extn. no. Mode
Outgoing Call (Day/Night Mode)
104
206
308
414
21,22,23,24
21,22,23,24,25
21,22,23,24,25
21,22,23,24,25
Round Robin
Round Robin
Round Robin
Round Robin
Calling Level
Local level at all extn.
Local level at all extn.
Local level at all extn.
Local level at all extn.
Mode
Rotational
Rotational
Rotational
Rotational
Caller ID
Trunk / Extn.
Enable
Enable
Enable
Enable
Note :- (1) Incoming call of trunk ring duration (max.) depend on service provider timeout limit.
(2) External FSK CLI ( Optional ), DTMF CLI inbuilt.
USER FUNCTION : DEFAULT STATUS
Always active User/System Defined
Intercom Call Junction No. Access (System program)
Last No. Redial Barge in (System program)
Answer/ Receive Call Call toggle (System program)
CLI Monitor (System program)
Call pickup Hot line (Extn./Jn.) (System / User program)
Selective call pickup Conference (System program)
Auto call Back(extn/jn) Day/Night Mode (System / User program)
Call transfer Dynamic Lock (System / User program)
Do not Disturb Relay (System program)
DND cancel Paging (System / User program)
Call Forward Global Dial (System program)
Call Forward cancel Trunk Reservation (System program)
Alarm Emergency dial (System program)
General Functional Information
Note :- 308/414 Model only support timer function like alarm, auto day night,.............etc.
RING PATTERN : DEFAULT STATUS
Ring Type Ring Pattern
Intercom Call
(a) Normal Long single cycle ring ______ Long pause
(b)Executive Small single ring ___ Small pause
(c) Cordless Long single cycle ring ___ Small pause
Trunk Call Double cycle ring___ Small pause
Note :- Default intercom ring pattern set as normal ring.
LED Status Abbreviations
RUN ON / OFF Blinking System normal condition
NIGHT MODE ON or OFF ON = Active night mode, OFF = Active Day mode
LINE 1/2/3/4 ON or OFF ON = Trunk line busy, OFF = Trunk line free
EXTN. LED ON or OFF (308 only) ON = Extension busy, OFF = Extension free
LED STATUS :
Inspire 104/206/308/414 User Guide 11

(A) TRUNK and EXTENSION ( TRK/EXT) CONNECTING PORT : ( Any type of phone set can connect )
General Installation Information
414
TRK 1
•• •• •• •••• •• •• •• •• •• •• •• •• •• •• •• •• •• ••
EXT1 EXT2 EXT3 EXT4 EXT5 EXT6 EXT7 EXT8 EXT9 EXT10 EXT11 EXT12 EXT13 EXT14TRK 2 TRK 3 TRK 4
61 62 63 64 21 22 23 24 25 26 27 28 29 30 31 32 33 34
CODE
308
TRK 1
•• •• •• •• •• •• •• •• •• •• ••
EXT1 EXT2 EXT3 EXT4 EXT5 EXT6 EXT7 EXT8TRK 2 TRK 3
61 62 63 21 22 23 24 25 26 27 28
CODE
206
TRK 1
•• •• •• •• •• •• •• ••
EXT1 EXT2 EXT3 EXT4 EXT5 EXT6TRK 2
61 62 21 22 23 24 25 26
CODE
104
TRK 1
•• •• •• •• ••
EXT1 EXT2 EXT3 EXT4
61 21 22 23 24
CODE
Note : (1) Never connect trunk line wire at extension port.
(2) Do not use loose AC 220V connecting point to avoid sparking.
(3) Installation place should be dry, airy & free from moisture.
(4) Properly pluged trunk wire & extension wire with EPABX port .
(5) Connect / Plug properly rosset box of telephone set.
(B) Configuration & Dimension (C) Power Management
EPABX Power SMPS Battery Backup Req. No. of
Model Supply cum Charger (Optional) Battery & Rating*
104
PS N. A. N. A.
206
308 PS SMPS 12V Battery 1 no.,
414 SMPS Backup (without battery) 12V,7AH
EPABX Total TRK Extn Dimension (cm)
Model Port (Max.) (Max.) W H D
104 5 1 4 17 20 5
206 8 2 6 17 20 5
308 11 3 8 19.5 21 6
414 18 4 14 24 24 8
(D) FND DIP SWITCH (SW) SETTING :
DIP Switch status 1st FND 2nd FND 3rd FND 4th FND
Switch point
SW ON
SW OFF
FND Port
1 2
EXTN. 24EXTN. 22
1 2
EXTN. 23
1 2
EXTN. 21
1 2
Default setting as 1st FND.
Inspire 104/206/308/414 User Guide 12
N.A. (not applicable)
Voice Disa
? 1 CH VDC
? Welcome / Error
Busy / No Reply
? Day & Night Greeting
Relay & Paging Card
? Paging (Option to connect
external audio amplifier for
announcement)
? Relay (Option to connect
external EM Door Lock or
Electric Gadgets)
MMOH (120 sec )
?Music Recordable
?Voice Recordable
?Put on Hold Replay
(E) Optional Add on Card for 308/414:
(F) Optional Product :
?Lighting Protected
?RF Noise Filter
?Models
• 2 Ports
• 4 Ports
LPU
( Line Protection Unit)
FCT ( Fixed Cellular Terminal ) GSM based
Single SIM Support
Omini Directional Antenna
RJ 11 Telephone port
EPABX Trunk port Connectivity
Signal Strenght Indication
CLI (Caller ID)

A. In the oponion of the company, the Product is modified or improperly
installed or tampered
B. The damage is caused during transit, by accident, fire, flood, abuse, misuse,
lighting strikes on extension / Jn. wiring, electrical surges & spikes and high input
voltage from the main supply.
The CRYSTAL PRODUCT is warrantied for a period of twelve months from the date of
purchase against defects in materials and workmanship (fair wear & tear excepted ).Our
obligation under this warranty is limited to the repair of any defective part only at our
option and does not cover any consequential or resulting liability damage or loss arising
from such defects. Expenses incurred in sending the defective unit or parts there of
and collecting the same back after repairs under the warranty from our service center
(Delhi) shall be borne by the customer :
The Warranty is void if :
SALES & SUPPORT DEALER
DEALER NAME
ADDRESS
CONTACT PERSON
CONTACT NUMBER
EMAIL ID
PRODUCT MODEL NO.
INVOICE DATE
Customer's Signature Dealer Sign. With Stamp
..........................................................................................
..........................................................................................
...........................................................................................
...........................................................................................
...........................................................................................
...........................................................................................
...........................................................................................
...........................................................................................
...........................................................................................
I / we have carefully read and understood the above terms and conditions to avail
the warranty of the product.
:
:
:
:
:
:
::
Inspire 104/206/308/414 User Guide 13

Inspirecss21082021
www.crystalpbx.com
MAKE IN INDIA
QR for all Product Manuals
System Features subject to change owing to constant innovations in technology without prior notice.
CRYSTALPRODUCTRANGE
Analog
Epabx
Digital
Epabx
Hybrid
IP-PBX
Analog - 5 to 40 Ports
Fixed & Flexible Model
Nexa, Inspire ZX Series
db 48/96/128 Flexi - 16 to 184 with PRI Hybrid with Modular Digital PRI PBX
db 32 Flexi - FX2, FX4, FX6, Model
db 48/96/128 Flexi -16 to 184 Ports
Support 64 port SIPEXTN
32 SIP CHANNEL
db
THE INTELLIGENT EPABX
Digital
TEC
APPROVED
PBT
Push Button Telephone
KTS/DSS
Key Telephone System
BCS
Audio Brodcast
Audio 16 Ports
Audio 16-240 Ports
Basic Phone CLI Phone
KTS DSS
TEC APPROVED
G2K Modular
16 Ports to ports64
16 Ports to 2048 ports
Guard
Society Intercom
Analog
Epabx
FCT with pen antenna
FCT with hi-gain antenna
GSM - FCT
( Fixed Cellular Terminal )
G2K Modular
1 to 10 Trunks Ports
4 to 64 Extension Ports
SN - 64 Model