CTC Union GS 6-8 Manual

1
CTC GS 6-8
End customer overview
CTC GS 6-8
Ground source heat pump
1. Sign the installation checklist.
2. Serial no. behind touchscreen.
3. Bleed radiator system and products,
approx. one month after installation + at least
once per year.
4. Screw in/close the bleed screw on the au-
tomatic bleeder approx. three months after
installation.
5. Fit/turn the safety valve,
approx. four times per year.
6. Check the system pressure regularly and ask
the installer what system pressure your system
should have. The system pressure must be
set 0.3 bar higher than the pre-pressure in
the expansion tank.
7. Regularly clean the dirt filter (close off incoming
tap water; remove and clean the filter)/solenoid
filter ball valve (close off the flow to the heat
pump; remove and clean the filter).
8. Set the correct heating curve for a comfortable
room temperature; check that the thermostat
valves on the element or floor heating are set
up correctly. These may need to be opened.
9. Set the hot water mode according to your
requirements.
Read the full instructions in the Installation and
Maintenance Manual
162 205 98-1 2018-09-26
4. automatic bleeder
2. serial number for registration
behind screen which can be
tilted
3. & 5. safety valve
7. dirt filter for
tap water
7. solenoid
filter ball valve
8 & 9. touchscreen
6. manometer

2CTC GS 6-8
Touchscreen
All product settings are set up via the touchscreen. Set the heat and hot
water settings here.
Outdoor sensor
Measures outdoor temperature; placement
should not be in direct sunlight or where
the measured outdoor temperature may be
misleading. The outdoor sensor provides the
product with information on the current need
for heat.
Room sensor
Measures indoor temperature and finely
adjusts the heating curve so that the product
runs more evenly. The room sensor is optional
and the product can work using only the
heating curve. The room sensor should
preferably not be activated until the heating
curve has been completely adjusted. The
room sensor is fitted at a central point in the
house, in the most open position possible.
This is the best position for the sensor to
record an average temperature for the house.
Clean, safe hot water
The water in the tank (as in the heat pump
and radiators) rises and is layered so that
the hottest water surrounds the DHW heat
exchanger where the tap water flows through
quickly, draws energy and flows out to the tap
or shower. This provides fresh hot water and
minimises the risk of legionella bacteria.
Cooling module
The energy in the bore hole (bedrock) or
ground is drawn up by the cooling system. The compressor then increases
the temperature to a usable level. Afterwards it releases the energy for
the heating system and hot water. Remember that the brine fluid must be
checked and refilled as needed.
Electrical operation
The product can also provide both heating and hot water to the building
when running on electricity only. With the heat pump connected, the
immersion heater works to provide additional heat as needed only. The
touchscreen can be used to set whether the immersion heater goes in and
with how much power.
Touchscreen
DHW heat
exchanger
Electrical
heat
Hot water
tank
Cooling
module

3
CTC GS 6-8
CTC GS 6-8
1 heating circuit
Basic installation, CTC GS 6-8
Options with CTC GS 6-8
* In addition to the basic installation, accessories are required such as: Extra sensor, mixing valve group 2, expansion
card etc.
Volume tank CTC VT 80 may be required for some houses (see installation manual for more information).
1

4CTC GS 6-8
See operation data
Room temperature heating circuit 1
-Measured by
Room sensor 1
Room temperature heating circuit 2
-Measured by
Room sensor 2
Tank temperature
-Measured by
Hot water sensor in the top of the tank.
Outdoor temperature
- Measured by
Outdoor sensor
Alarm management
See troubleshooting chart at the very
back of the installation manual.
Navigate on the touchscreen
Home
The Home button
takes you back to the
Start menu.
Return
The Return button takes
you back to the previous
level.
OK
The OK button is used
to mark and confirm
text and options in the
menus.
+ / -
Press + to increase value
Press - to decrease
value
Arrow & OK
Press up arrow
to increase value
Press OK to
save settings
Press down
arrow to
decrease value
Home screen
Larm: [E055] Fel fasföljd
Återställ larm
Larm:Felfasföljd kompressor
Återställ larm
Green LED – status OK
Red LED – alarm
The serial number
(12 digits) can be
found behind the
display. This number
needs to be given
to the installation
engineer and CTC
support in the event
of a fault report.
Press to see detailed information on each
part
Call your installation engineer in the first
instance
Serial number
XXXX-XXXX-XXXX
article group–year/week–sequential number
serial number
software update
Alarm: Wrong phase order
compressor
Reset alarm
1
2
2
22,2 ºC 21,2 ºC 58 ºC -5 ºC
Room temp. DHW Operation
CTC GS 8 Monday 09:35
Installer
Operation data system
1 2 2

5
CTC GS 6-8
More settings and tips in the installation and service manual
Fine adjustment Increase/decrease heat
If the outdoor
temperature is lower
than 0°C.
Change inclination
Coarse adjustment Increase/decrease heat
Select:
Heating circuit
++
+
If the outdoor
temperature is higher
than 0°C.
Change adjustment
Heating circuit
Max primary flow ºC 60
Min primary flow ºC Off
Heating, mode Auto
Heating, mode, ext
Heating off, out ºC 18
Heating off, time 120
Inclination ºC 50
Adjustment ºC 0
Night reduction disable ºC -14
Room temp reduced ºC -2
or
Primary flow reduced ºC -3
Alarm room temp ºC 5
Smart low price ºC 1
Smart over capacity ºC 2
Max time heating 20
Charge pump % 60
Drying period mode Off
Drying period temp ºC 25
Push OK to confirm
changes
+
Set heating
1 2
Night reduction Holiday
Heating circuit 2 (50)
Heating System 1
Room temp.
Measured temp
Room sensor
Desired
Setpoint
1 2
Night
reduction
-Set a higher
or lower
temperature at
certain times of
day.
Holiday
-Set higher or
lower temperatures
on certain days.
Fine adjustment with
no room sensor. To
allow the temperature
to be changed even
more, use the coarse
adjustment on the
right.
Change hot tap water temperature
For detailed information on other hot
water settings, please refer to the
Installation and Maintenance instructions.
Control normal mode for hot water
production.
Economic – Small DHW requirement.
Normal – Normal DHW requirement.
Comfort – Large DHW requirement.
Weekly program
- Set weekly interval
for extra hot water
Set hot water
The product will start to
produce additional hot
water.
Extra
hot water 0.0 hours
On
Temperature
Normal
Weekly program
DHW
Installer
“Installer” is used by the installer to configure the settings and servicing for
your heating system.
Allow additional heat and immersion heater for safe comfort
at all times
To ensure hot water comfort in all operating conditions, it may be
necessary to allow additional heat. If there is no heat pump or other
heat source installed, these settings need to be changed so that
the product can function as an electric boiler.
Select: Hot
water tank
++Change:
Add heat DHW – Yes
+
1 2 2
Rumstemperatur Varmvatten
1 2 2
Rumstemperatur Varmvatten
1 2 2

6CTC GS 6-8
Heat settings
The product regulates itself to provide a constant, comfortable temperature
throughout the year using the set heating curve. The curve may need to be
changed using the touchscreen if the room temperature feels too cold or hot
over time. For information on how to do this, see “Navigate touchscreen”
on the previous page. Correction may be required for a few weeks after
installation until the system has been matched to the building. For more
information, see the Installation and Maintenance Manual, section: The house
heating curve.
Examples of inclination values for different systems
Floor heating only inclination = 35
Low temperature system (well insulated houses) inclination = 40
Normal temperature system (factory setting) inclination = 50
High temperature system (older houses, small radiators, poorly insulated) inclination = 60
Example in image:
1. Inclination 50, Adjustment 0°
2. Inclination 40, Adjustment 0°
3. Inclination 50, Adjustment 5°
Find the right heating curve
• The heating curve for the house is determined by two main factors:
inclination and adjustment. These can be changed to fit the house’s
energy needs for heating.
• The house’s heating needs depend on:
The size of the house (volume/area)
Insulation
Window area
-> inclination and adjustment increase the more energy is required
• Thermal conductivity of the radiators
- Elements
- Floor heating
- Number of elements/surface for heat transfer
-> inclination and adjustment decrease the faster energy is discharged
outdoor
temperature
water temp. out on the elements
inclination
adjustment
Change inclination when
outdoor temperature < 0°C
Change adjustment when
outdoor temperature > 0°C
(inclination 50)
(inclination 40)
1
2
3

7
CTC GS 6-8
The total energy consumption of the product is linked to:
• The energy needed by the house, which varies significantly through
the year depending on the outdoor temperature (see image on energy
consumption, right).
• DHW consumption.
iRemember:
• Energy consumption is much higher in the winter
months than in the summer months
• Energy consumption increases when DHW
consumption is high
• What is important is the total energy bill for the year.
Energy-saving tips
• Make sure that the thermostat valves on the house’s element are open in
most rooms; only adjust downwards in bedrooms, for example.
• Use the DHW chart for extra DHW to avoid high-temperature operation
when it is not needed.
• Install a room sensor; this provides more even heat and compensates for
natural solar radiation or other natural heat sources.
• Clean any dirt filters regularly; a deterioration in water flow can increase the
electricity used by the circulation pump.
• Make sure the speed of the charge/circulation pump provides the right flow
(see the chapter “System adjustments” in the Installation and Maintenance
Manual).
Energy consumption
J
a
n
F
e
b
M
a
r
A
p
r
M
/
J
/
J
/
A
S
e
p
O
c
t
N
o
v
D
e
c
kWh

Checklist
The checklist must always be completed by the installation engineer
• In the event of a service, this information may be called for.
• Installation must always be carried out according to the installation and maintenance instructions.
• Installation must always be carried out in accordance with best professional practice.
• Following installation, the unit must be inspected and checked for functionality.
The points below must be checked off.
Pipe installation
Product filled, positioned and adjusted in the correct manner according to the instructions.
Product positioned so that it can be serviced.
Capacity of charge pump (G11) adjusted for correct flow.
Open radiator valves and other relevant valves.
Tightness test.
Bleed the system.
Safety valve function test.
Waste pipe connected to floor drain.
Electrical installation
Omnipolar switch
If the heat pump is installed: heat pump activated and started
Electric power (kW) and fuse, adapted to the property, in heating mode, in hot water mode and backup mode
Correct tight wiring
Requisite sensors for selected system
Outdoor sensor
Room sensor (optional)
Current sensor
Accessories
Information for the customer (adapted to current installation)
Start-up with customer/installer.
Menus/controls for selected system
Installation and maintenance manual supplied to the customer
Check and filling, heating system
Trimming information, heat curve
Alarm information
Safety valve function test
Warranty and insurance
Information on procedures for fault registration
The above points have been reviewed upon installation
Date/Place Signature/DHW installation engineer Tel. no.
Customer’s signature Signature/Electrician Tel. no.
Product Serial number