CTE TECH 8198 User manual

8198 instruction of meter
Product name：Meter (w ith Bluetooth function)
Brand：CTE TECH CORP.
Model： 8198
1. Product explanation：
Vehicle device for large-sized motorcycle and provides a status of vehicle.
This meter can display such as vehicle speed, fuel quantity, total mileage, short
mileage, battery voltage, indicator light, time, gear position, remaining mileage,
average speed, average fuel efficiency, time functions, and also provides users with
the operation of the meter buttons to set the suitable interface for the users.
Meter button operation:
L can switch mileage mode: Change the mileage mode ODO＞＞TRIP A＞＞
TRIP B＞＞ODO
R can switch driving status: instantaneous fuel consumption->>average fuel
consumption>>remaining mileage>>average speed>>walking time-->battery
voltage--instant fuel consumption
2. Specification：
System specification
Description Content
Size of main body 158.5*103.4*54mm
Wired connection interface 20pin connection interface
Wireless connection interface Bluetooth (BLE5.0)
APP Rideology
Outer case material AES+PMMA
Weight 305g
Operating Voltage DC 9V~16V +/-0.5V
Operating Current 150mA~500mA
Quiescent Current (Key OFF) 0.8mA
Operating temperature -20~70℃
Storage temperature -30~80℃
Random Access Memory 4MB

3. Input/output interface characteristics：
PIN Description Input /Output Electrical characteristics
1 BAT Input Battery power
2 IGN Input Key ON/OFF 12V , High will be ON, Low will be OFF
3 GND GND
4 NEUTRAL Input NEUTRAL
5 OIL Input OIL
6 ABS Input ABS
7 KTRC Input KTRC
8 ECU Input /Output ECU
9 SPEED Input SPEED
10 TACHO Input TACHO
11 FUEL Input FUEL
12 AGND Analog Ground
13 TURN-L Input 12V, High will be ON, Low will be OFF
14 TURN-R Input 12V, High will be ON, Low will be OFF
15 HB Input 12V,High will be ON, Low will be OFF.
16 ETC R Input 5V, High will be ON, Low will be OFF.
17 ETC N Input 5V High will be ON, Low will be OFF.
18 K.S.O Input /Output Connect to KVCS(Kawasaki Vehicle Communication System)
19 UP SW Input Switch mileage mode
20 DOWN SW Input Switch driving mode

4.Bluetooth connection：
4-1.Follow below instructions to establish connection between the dashboard and
user device：
Step 1:
Short press of left button to change the ODO display to TRIP A display , then long
press of left and right buttons to enter Menu.
Step 2:
Short press of left button to move the selection to Bluetooth
then short press of right button to enter Bluetooth setting.
Step 3:
Short press of right button to enter Bluetooth ON/OFF setting.
Step 4:
Short press of left button to move the selection to ON
then short press of right button to confirm.
Step 5:
Run the Rideology APP on your device.
Step 6:
Setting>>Pairing Vehicle pairing

Step 7:
Choose “Ninja H2”for pairing.
Step 8:
Step 9:
Input the Pass Key displayed on the dashboard to establish the connection.
Step 10:
Connection established

5.Bluetooth E-Label display：
Step 1:
Short press of left button to change the ODO display to TRIP A display , then long
press of left and right buttons to enter Menu.
Step 2:
Short press of left button to move the selection to Bluetooth
then short press of right button to enter Bluetooth setting.
Step 3:
Short press of left button to the second page and the E-Label will be shown.
E-Label：
Destination Mark
U.S FCC ID：2AS3E-8198
Canada IC：24983-8198
Europe
Australia
Taiwan
Japan
Philippines
Thailand X
Malaysia
India X
Korea

Brazil
Indonesia
China
FCC Statement:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
IC Statement:
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not cause interference,
and (2) this device must accept any interference, including interference that may cause undesired
operation of the device.
Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisee aux deux conditions suivantes : (1) l'appareil ne
doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage
radioelectrique subi, meme si le brouillage est susceptible d'en compromettre le fonctionnement.

Taiwan requlatory information(NCC)
低功率電波輻射性電機管理辦法
第十二條 經型式認證合格之低功率射頻電機，非經許可，公司、商號
或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及
功能。
第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通
信；經發現有干擾現象時，應立即停用，並改善至無干擾時方得
繼續使用。
前項合法通信，指依電信法規定作業之無線電通信。
低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射
性電機設備之干擾。
警語：
1) 電磁波警語：減少電磁波影響，請妥適使用(無線電信終端設備適用)、
2) 視力保護警語：使用過度恐傷害視力，建議每天看螢幕不超過 1小時。