AEMC instruments SR759 User manual

AC Current Probe
Model SR759
User Manual
DESCRIPTION
The SR759 (Catalog #2116.33) is designed for use in industrial environments. The ergonomic design allows
itm to easily attach to cables or small bus bars. The “circular” jaws guarantee a very good accuracy and low
phase shift. The probe has four measurement ranges with the highest range measuring to 1000Arms
continuous and is compatible with any AC Voltmeter, multimeter, or other voltage measurement instrument
that has the following features: Range and resolution capable of displaying 1mV of output per amp of
measured current; Voltmeter accuracy of 0.75% or better to take full advantage of the accuracy of the
probe; Input impedance of ≥10MΩ.
WARNING
The safety warnings are provided to ensure the safety of personnel and proper operation of the
instrument. Read the instruction completely.
• Use caution on any circuit: potentially high voltages and currents may be present and may pose a
shock hazard.
• Do not use the probe if damaged. Always connect the current probe to the measuring device before it
is connected around the conductor
• Do not use on non-insulated conductor with a potential to ground greater than 600V CAT III pollution
2. Use extreme caution when clamping around bare conductors or bus bars.
• Before each use, inspect the probe; look for cracks in housing or output cable insulation.
• Do not use clamp in wet environment or in locations that hazardous gases exist.
• Do not use the probe anywhere beyond the tactile barrier.
INTERNATIONAL ELECTRICAL SYMBOLS
This symbol signifies that the current probe is protected by double or reinforced insulation. Use only
factory specified replacement parts when servicing the instrument.
This symbol signifies CAUTION! and requests that the user refer to the user manual before using
the instrument.
This is a type A current sensor. This symbol signifies that application around and removal from
HAZARDOUS LIVE conductors is permitted.
DEFINITION OF MEASUREMENT CATEGORIES
CAT IV: For measurements performed at the primary electrical supply (<1000V) such as on primary
overcurrent protection devices, ripple control units, or meters.
CAT III: For measurements performed in the building installation at the distribution level such as on
hardwired equipment in fixed installation and circuit breakers.
CAT II: For measurements performed on circuits directly connected to the electrical distribution system.
Examples are measurements on household appliances or portable tools.
RECEIVING YOUR SHIPMENT
Upon receiving your shipment, make sure that the contents are consistent with the packing list. Notify your
distributor of any missing items. If the equipment appears to be damaged, file a claim immediately with the
carrier and notify your distributor at once, giving a detailed description of any damage.

ELECTRICAL SPECIFICATIONS
Current Range:
1mA to 1.2A, 0.01 to 12A, 0.1 to 120A, 1 to 1200A
Output Signal: 1000mV/AAC (1V @ 1A),
100mV/AAC (1V @ 10A), 10mV/AAC (1V @
100A), 1 mV/AAC (1V @ 1000A)
Accuracy and Phase Shift*:
1A Range
Primary Current
Accuracy %
Phase Shift
0.001 to 0.01A
3% + 1mV
Not Specified
0.01 to 0.1A
≤3% + 1mV
Not Specified
0.1 to 1A
≤0.7% + 1mV
≤10°
1 to 1.2A
≤0.7% + 1mV
≤10°
10A Range
Primary Current
Accuracy %
Phase Shift
0.01 to 0.1A
1% + 0.2mV
Not Specified
0.1 to 1A
≤0.5% + 0.2mV
≤5°
1 to 10A
≤0.5%
≤2°
10 to 12A
≤0.5%
≤2°
100A Range
Primary Current
Accuracy %
Phase Shift
0.1 to 1A
1% + 0.2mV
Not Specified
1 to 10A
≤0.5% + 0.2mV
≤2°
10 to 100A
≤0.3%
≤1°
100 to 120A
≤0.2%
≤1°
1000 A Range
Primary Current
Accuracy %
Phase Shift
1 to 10A
1% + 0.2mV
Not Specified
10 to 100A
≤ 0.5% + 0.2mV
≤ 2°
100 to 1000A
≤ 0.2%
≤ 1°
1000 to 1200A
≤ 0.2%
≤ 1°
*Reference conditions: 23°C ± 3°K, 20 to 75% RH, 48
to 65Hz, external magnetic field < 40A/m, no DC
component, no external current carrying conductor, test
sample centered. Load impedance 10MΩ

Overload: 1200A for 15 min on, 30 min off
Accuracy: Per IEC 185
Frequency Range: 30Hz to 3kHz; current
derating above 500Hz using the formula:
×

()
Load Impedance: 100kΩmin
Working Voltage: 600V CAT III
Common Mode Voltage: 600V CAT III
Influence of Adjacent Conductor: < 1mA/AAC
Influence of Conductor in Jaw Opening:
0.3% of Reading
Influence of Frequency:
1mV/A Range: < 1% R from 10Hz to 1kHz
10mV/A Range: < 1.5% R from 10Hz to 3kHz
100mV/A Range: < 2% R from 10Hz to 3kHz
1000mV/A Range: < 2% R from 30Hz to 1kHz
Open Voltage: 8V peak max.
MECHANICAL SPECIFICATIONS
Operating Temperature:
14° to 122°F (-10° to 50°C)
Storage Temperature:
-4° to 158°F (-20° to 70°C)
Influence of Temperature:
< 0.15% per 10°K
Influence of Humidity:
From 10 to 90%: 0.1%
Jaw Opening: 2.25" (57mm) max
Maximum Conductor Size:
2.05" (52mm)
Envelope Protection: IP 40 (IEC 529)
Drop Test: 1 m (IEC 68-2-32)
100 g (IEC 68-2-27)
Vibration:
5 to 15Hz, 0.15mm (IEC 68-2-6)
Material:
Handles and jaws: Polycarbonate UL94V0
Dimensions:
4.37 x 8.50 x 1.77" (111 x 216 x 45mm)
Weight:
1.21 lbs (550g)
Output:
Two-core cord with reinforced or double insulation,
1.5m (5ft) terminated with 2 safety plugs (4mm)
SAFETY SPECIFICATIONS
Electrical Conformity to International Standards:
This instrument is compliant with IEC 61010-2-032,
300V category IV and 600V category III.
Double or reinforced insulation .
Type of current sensor per IEC 61010-2-032:
type A .
Electromagnetic Compatibility:
The device is in conformity with standard IEC
61326-1.
ORDERING INFORMATION
AC Current Probe SR759 ................ Cat #2116.33
Accessories:
Adapter - Banana (Female) – BNC
(Male) (XM-BB) (600V CAT III) ........ Cat #2118.46
Banana plug adapter
(to non-recessed plug) ...................... Cat #1017.45
25 to 55Hz, 0.25mm
15 to 25Hz, 1mm

99-MAN 100168 v13 08/21
OPERATION
Please make sure that you have already read and fully understand the WARNING section on page 1.
Making Measurements with the AC Current Probe Model SR759
•Connect the black and red terminals to the 2VAC range of your DMM or voltage measuring instrument.
Select the appropriate current range (1000/1V). Clamp the probe around the conductor to be tested with
the arrow pointed toward the load. Read the value display on the DMM and multiply it by the probe ratio
selected. (e.g. If reading = 185mV, the current flowing through the probe is 185 x 1000 = 185,000mA =
185A when 1mV/A range is selected.)
•For best accuracy, avoid if possible, the proximity of other conductors which may create noise.
Tips for Making Precise Measurements
•When using a current probe with a meter, it is important to select the range that provides the best
resolution. Failure to do this may result in measurement errors.
•Make sure that probe jaw mating surfaces are free of dust and contamination. Contaminants cause air
gaps between the jaws, increasing the phase shift between primary and secondary. It is very critical for
power measurement.
MAINTENANCE
Warning:
•For maintenance use only original replacement parts.
•To avoid electrical shock, do not attempt to perform any servicing unless you are qualified to do so.
•To avoid electrical shock and/or damage to the instrument, do not get water or other foreign agents
into the probe.
Cleaning: To ensure optimum performance, it is important to keep the probe jaw mating surfaces clean at all
times. Failure to do so may result in error in readings. To clean the probe jaws, use very fine sand paper (fine
600) to avoid scratching the jaw then gently clean with a soft oiled cloth.
REPAIR AND CALIBRATION
You must contact our Service Center for a Customer Service Authorization number (CSA#). This will ensure
that when your instrument arrives, it will be tracked and processed promptly. Please write the CSA# on the
outside of the shipping container.
Chauvin Arnoux®, Inc. d.b.a. AEMC® Instruments
15 Faraday Drive • Dover, NH 03820 USA
[phone] x360 • [phone] x360 • [e-mail]
(Or contact your authorized distributor)
NOTE: All customers must obtain a CSA# before returning any instrument.
TECHNICAL AND SALES ASSISTANCE
If you are experiencing any technical problems, or require any assistance with the proper use or application
of this instrument, please contact our technical hotline:
[phone] (Ext. 351) • [phone] (Ext. 351) • [e-mail]
LIMITED WARRANTY
The current probe is warranted to the owner for a period of two years from the date of original purchase
against defects in manufacture. This limited warranty is given by AEMC®Instruments, not by the distributor
from whom it was purchased. This warranty is void if the unit has been tampered with, abused or if the defect
is related to service not performed by AEMC®Instruments.
Full warranty coverage and product registration is available on our website at: www.aemc.com/warranty.html
Please print the online Warranty Coverage Information for your records.