Cuanbo WP-MAC-E1 User manual

Tel:[phone] ShenZhen Aviation intelligent technology Co, Ltd
Fax:[phone]
Cuanbo WP-MAC-E1
User manual
Before using the system, please read the manual carefully and keep the manual
copyright© Cuanbo 2018
Without the written consent from Cuanbo, no unit or individual is allowed to extract
or copy part or all of the contents of this manual, and it is not allowed to spread
in any form.
The products described in this manual may contain software with copyright enjoyed
by Cuanbo and its potential licensors. Unless the permission of relevant right
holders is obtained, no one can copy, distribute, modify, extract, decompile,
disassemble, decrypt, reverse engineer, rent, transfer and other acts infringing
the software copyright in any form.
Cuanbo reserves the right to modify and interpret the product specifications or
related information mentioned in this manual without prior notice.

Tel:[phone] ShenZhenAviation intelligent technology Co, Ltd
Fax:[phone]
Note
Some features and functions of the product and its accessories described in this
manual depend on the design and performance of the site environment and the software
you install. Some features and functions may not be implemented due to the field
environment devices or the software you installed is not support, or due to the
limitations of the field environment. Therefore, the description in this manual may
not exactly correspond to the product you purchased or its accessories.
Prompt symbol
In order to ensure that you can correctly complete the installation and use of this
product, please pay attention to the special meaning of the following symbols in
the manual
产
This symbol on the product intend to warn the user that there is
a dangerous voltage exposed in the case of the product, danger
of electric shock
This symbol on the product intend to remind the user that there
are important operation and maintenance (repair) instructions in
the user manual attached with the equipment
illustration：XXXXXXXXXXXXXXXXX –XXXXXXXXXX - XXXXXXXXXXX
This symbol on the user's manual intend to remind the user that there are
important instructions or operations in this position of the manual

Tel:[phone] ShenZhenAviation intelligent technology Co, Ltd
Fax:[phone]
Content
Catalog ........................................... Błąd! Nie zdefiniowano zakładki.
Safety instructions ............................... Błąd! Nie zdefiniowano zakładki.
1 summary ......................................... Błąd! Nie zdefiniowano zakładki.
Function introduction .............. Błąd! Nie zdefiniowano zakładki.
2 Installation and preparation .................... Błąd! Nie zdefiniowano zakładki.
2.1 product list ................... Błąd! Nie zdefiniowano zakładki.
WP-MAC-E1 structure ................ Błąd! Nie zdefiniowano zakładki.
Interface description .............. Błąd! Nie zdefiniowano zakładki.
2.2 Placement of education integrated machineBłąd! Nie zdefiniowano zakładki.
3 instruction manul ................................ Błąd! Nie zdefiniowano zakładki.
3.1 Turn on the power .............. Błąd! Nie zdefiniowano zakładki.
3.2 Signal source switching ........ Błąd! Nie zdefiniowano zakładki.
3.3 system setup .................. Błąd! Nie zdefiniowano zakładki.
3.4 RS232/LAN Control instruction .. Błąd! Nie zdefiniowano zakładki.
3.5 web management ................. Błąd! Nie zdefiniowano zakładki.
4 troubles and maintenance ........................... Błąd! Nie zdefiniowano zakładki.
4.1 regular review working environmentBłąd! Nie zdefiniowano zakładki.
4.2 regular review terminal cable ....... Błąd! Nie zdefiniowano zakładki.
4.3 Software upgrade ............... Błąd! Nie zdefiniowano zakładki.
4.4 diagnostic trouble ................... Błąd! Nie zdefiniowano zakładki.
4.5 Common Trouble treatment ............ Błąd! Nie zdefiniowano zakładki.
4.6 Abnormal parts maintenance ..... Błąd! Nie zdefiniowano zakładki.
4.7 Cleaning precautions ........... Błąd! Nie zdefiniowano zakładki.
4.8 Warranty instructions .......... Błąd! Nie zdefiniowano zakładki.
4.9 warm hint ...................... Błąd! Nie zdefiniowano zakładki.
4.10 contact us .................... Błąd! Nie zdefiniowano zakładki.

Safety instructions
If these precautions are ignored, it may lead to personal injury or casualties,
equipment damage, data loss, equipment performance degradation or unpredictable
results
Electrical safety
⚫In order to avoid serious damage caused by possible electric shock, please
remove the power cord from the product power interface temporarily before
moving the product.
⚫When you need to add new hardware to the product or remove the existing
hardware in the product, be sure to turn off the product power first. If
conditions permit, it is recommended to remove the power cord from the
product interface temporarily.
⚫Before use, confirm whether the product has been grounded and whether the
power supply voltage has been adjusted to the applicable range of the product.
Otherwise, it may cause damage, performance degradation or unpredictable
results.
⚫Don't use the loose or damaged power socket or touch the power socket when
hands are wet, otherwise there will be the danger of electric shock and fire.
⚫If you hear the noise from the power cord and the power interface, please
unplug the power cord immediately and ask your sales representative for help,
otherwise there will be a risk of fire or electric shock.
⚫If any foreign matter or liquid enters the product or needs to clean the
product, please remove the power cord and any other cables from the product,
otherwise there will be the risk of electric shock, fire and damage to the
product.
⚫If the power supply is damaged, please do not try to repair it by yourself.
Please contact the professional and technical service personnel or dealers
to deal with it.
⚫This product uses 60227 IEC 53 300 / 500V, power supply connecting wire
conform to GB / T 5023.5-2008 / IEC 60227-5:2003 standard.
Operation safety
⚫Please keep away from the damp place when operating the product, otherwise
the product may work abnormally and cause the risk of short circuit.
⚫Please operate the equipment in the temperature range of 0-70 ℃(32-158 ℃)
and humidity range of 10% - 80%.
⚫Please do not directly expose the equipment to direct sunlight in the
enclosed space. Prolonged exposure to high temperature may cause abnormal
work, deformation or fire of the product.

⚫Please handle packaging materials properly, such as plastic bags, etc.
⚫Please try to keep the environment clean and avoid dust, otherwise there
is a risk of damaging the product.
⚫When using the product, keep away from electromagnetic field as far as
possible.
Do not discard this product as general garbage. The components of this
product are designed to be recyclable. This crossed dustbin symbol
indicates that this product (Electrical and electronic equipment)
should not be regarded as general garbage. Please dispose according
to the disposal method of waste electronic products in your area

WP-MAC-E1 Education Panel user 's manual
website:http://www.cuanbo.com
3
Tel:[phone] ShenZhenAviation intelligent technology Co, Ltd
Fax:[phone] Http://www.cuanbo.com
1outline
The integration of educational panel(WP-MAC-E1) IOT into smart classroom is the
practical demand of school application: with the continuous expansion of school
scale, the traditional school life and teaching management methods have been unable
to meet the needs of classrooms and students under the current situation of
information expansion. It has become the inevitable demand of school construction
to make full use of Internet, Internet of things and other technologies to build
smart classroom, The application of IOT in smart classroom is mainly reflected in
teaching management and campus life.
1. Teaching management: in the aspect of teaching management, through the IOT
system, the equipment in the space is automatically managed and controlled, which
brings the convenience of information for teachers. At the same time, the data
generated in this process can provide decision-making basis for teaching after
processing.
2. Campus life: intelligent monitor and control of lighting, power monitor,
energy consumption management and other aspects can be realized through the Internet
of things technology. The system can achieve the goal of "Low Carbon Campus" and
"green campus", and realize the fine use of equipment and real-time management
through the system, which greatly facilitates the school management, It can provide
decision-making reference for system optimization management.
The panel type Internet of things central control integrated machine is a
multimedia central management system ,which integrate key control panel, central
control, video matrix and card reader. Compared with the products on the market,
our products are more integrated, simpler wiring, better stability, more convenient
operation, more cost saving for customers, and more responsive. In addition, the
device can be connected with the campus card system and centralized management
software, providing a comprehensive and unique solution for the campus multimedia
classroom.
Function introduction
Multi type video interface signal exchange
WP-MAC-E1 education panel has 4 channel input and 3channel output. The input
interface has 2 HDMI interfaces, 2 VGA interfaces, the output interface has 2 VGA

4
Tel:[phone] ShenZhenAviation intelligent technology Co, Ltd
Fax:[phone]
interfaces and 1 HDMI interface. Each HDMI interface supports HDMI 1.4 standard,
4K × 2K resolution, 3D video and other high-resolution signal exchange, max
resolution up to 3840 × 2160@30Hz
It has the ability of local signal equalization and long-distance transmission
WP-MAC-E1 education panel has the ability of local signal equalization and
long-distance transmission. The local signal equalization function can provide 30
m automatic cable equalization for each HDMI or VGA input when using Cuanbo DX cable.
Audio function
WP-MAC-E1 education panel supports one channel of embedded and one channel of
de-embedded audio, and the channel can be customized
Simple management and more comprehensive functions
WP-MAC-E1 education panel is equipped with 5-inch LCD touch screen. The touch
screen can customize the control interface and scene according to the user's needs,
which is flexible and convenient to operate. supporting app software of IPAD and
web pages,it can manage the working signals of the education panel, such as: view
the signal source connection status information, input and output signal format,
resolution, HDCP status view, EDID saving and distribution, switch relay, etc. In
addition, WP-MAC-E1 also supports the functions of one click to class and one click
to finish class. At the same time, it also supports web online burning host program
and 2pcs USB3.0 input interfaces.
Central control management, control mode
WP-MAC-E1 education integrates central control management functions, it can
send control commands to external devices. Control data types include RS-232, RS-485,
IR (infrared), relay switch, etc, The RS232 control signal on the education panel
function can realize the creation of central control key, code input, IR learning
and control through APP software and control web page. It supports RS232 industrial
host control, PC Ethernet web page control implementation, iPad, mobile phone
control
Main technical parameters

5
Tel:[phone] ShenZhenAviation intelligent technology Co, Ltd
Fax:[phone]
model
WP-MAC-E1
size
19.2*9.4cm
Video input
3*HDMI，1*VGA
Video output
2*HDMI, 1*VGA
input voltage
DC 12-24V
Input current
≤3 A
power dissipation
machine≤15 W
fuse spec
32 V 3A
Storage temperature /
humidity
-20℃～85℃/ 20%～60%
working temperature /
humidity
0℃～60℃/ 10%～80%
Environmental height limit
0 ～2000M
Environmental pressure limit
≤79.5 kPa
Exchange signal
TMDS
exchange electrical level
+0.6 V ～+1.2 V
max TMDs channel bandwidth
3.2G bit/s
Max video interface
bandwidth
3.2G bit/s
Max audio sampling
48kHz
Max color depth
1080P 36 bit/px; 4K 24 bit/px
Port impedance
50Ω/ 100Ω
Clock recovery
automatic
DDC Channel protocol
DDC DDC2B

6
Tel:[phone] ShenZhenAviation intelligent technology Co, Ltd
Fax:[phone]
DDC electrical level
5 Volts p-p(TTL)
Average channel switching
time
≤5S
Serial control interface
4 bidirectional RS-232, 3pin Phoenix connector jack
2 RS-422 / RS-485 interfaces, 4Pin Phoenix connector
jack
Interface definition
RS-232：PIN 1:TX PIN 2:RX PIN 3:GND
RS-422/RS485：PIN1：RX- PIN2：RX+ PIN3：TX- PIN4：
TX+
Baud rate
9600 ~ 115200 (default)option, 8 data bits,
1 stop bit, no parity, no flow control
control protocol
ASCII 码
Ethernet control interface
1pc RJ-45 jack
Ethernet data rate
10/100BaseT，Half / full duplex, adaptive
Ethernet Support Protocol
ICMP，ARP，IP，TCP，UDP，DHCP，HTTP
Upgrade interface
RJ45 network port
Upgrade mode
WEB Control platform
USB interface
2pcs USB3.0 input,1pc USB3.0 output
size/weight
L192×W94×H41.1mm / 0.5kg
Table1.1 Main technical parameters
illustration：
⚫Input VGA interface supports the input of video and audio signals
⚫The output VGA interface supports the output of video and audio
signals
2Installation and preparation
Thank you for purchasing Cuanbo ®WP-MAC-E1 education panel. The advent of this
product not only shows the strict requirements of the product for high quality, high
performance, high stability and high service once again, but also adds many new

7
Tel:[phone] ShenZhenAviation intelligent technology Co, Ltd
Fax:[phone]
functions and a large number of applications, WP-MAC-E1 education panel is a rare
shining star in the products of cuanbo.
2.1 Product list
After you get the package of this product, please check whether the standard
accessories listed below are included
WP-MAC-E1 Education
Panel 1pc
user’s manual 1pc
Program CD 1pc
power adapter 1pc
IR/TX extension cable
2pcs
3PIN Phoenix connector
5pcs
2PCS
4PIN Phoenix connector
2pcs
2PIN Phoenix connector
5pcs
illustration：
⚫If any of the accessories listed above are damaged or missing,
please contact your dealer as soon as possible
⚫The above graphic for reference only. The contents of the actual
packing box will vary with the model you purchase
Interface description
DC Power interface
The DC power interface of WP-MAC-E1 education plane adopts 2pin3.5mmm Phoenix

8
Tel:[phone] ShenZhenAviation intelligent technology Co, Ltd
Fax:[phone]
connector. Connected with the power connector of the product is a power adapter with
rated voltage of 12-24 v. the power supply voltage should not exceed the rated voltage
range of the switching power supply to avoid accidents. Figure 2.3 shows the power
connector used in the product; the left side is the negative pole connected to the
power connection cord, and the right side is the positive pole connected to the power
connection cord
Figure 2.3 Definition of 12-24V power cable connector interface
RS-232 control interface
WP-MAC-E1 education panel provides standard serial communication port, which
allows users to use various control systems (such as personal computer and central
controller) to control in addition to switching operation by using the front panel
keys. The RS-232 control interface is connected with the control equipment by 3pin
cable connector male seat. The cable connector on the product is 3pin female seat.
The specific definition is shown in Figure 2.4. Please use the matching cable when
connecting.
Figure 2.4 RS-232 cable connector interface definition
IR and RS-422/485control interface
WP-MAC-E1 education panel provides IR control and IR learning functions, which
can control peripheral device through IR. At the same time, there is RS-422 / 185
communication port, which allows users to use various control systems (such as
personal computer and central controller) to control in addition to switching
operation by using the front panel keys.
The IR and RS-422 / 485 control interfaces are connected with the control
equipment by the 4Pin cable connector. The cable connector on the product is the
4Pin female block. The specific definition is shown in Figure 2.4. Please use the
matching cable when connect.
GND
RX
TX
IR-
IR+
IR-
IR+

9
Tel:[phone] ShenZhenAviation intelligent technology Co, Ltd
Fax:[phone]
Figure2.6 IR cable connector definition
Figure2.7 RS-422/485 IR cable connector definition
LAN control interface
WP-MAC-E1 education panel provides not only serial communication port, but also
LAN control interface. The RJ-45 connector is used to connect the LAN control
interface with the control equipment; if the control mode is point-to-point, the
network cable should use the cross cable. If the control mode passes through the
switch, router and other switching equipment, the direct network cable can be used.
The specific definition is shown in Figure 2.5
Figure 2.8 LAN control interface
TX+
TX-
RX+
RX-

10
Tel:[phone] ShenZhenAviation intelligent technology Co, Ltd
Fax:[phone]
2.2 placement of education integrated machine
WP-MAC-E1 education panel can be horizontally installed on the desktop or hollow
wall, but it must be fixed with screws to prevent falling damage. The display screen
is fragile. It is forbidden to place objects or collide with other objects. In order
to ensure the normal heat dissipation of the equipment, it is better to reserve some
space on both sides
Figure2.9 mainstay diagrammatic sketch

11
Tel:[phone] ShenZhenAviation intelligent technology Co, Ltd
Fax:[phone]
3Operate instruction
education panel of Cuanbo®WP-MAC-E1 can be controlled by RS-232, Ethernet and
touch screen. Users can choose one or more combinations according to the actual
situation. This chapter mainly introduces the operation and control mode of
education integrated machine.
3.1 Turn on the power
WP-MAC-E1 education panel is powered by DC 12-24 V voltage. Before turning on
the power supply, the power cable should be correctly connected as required. For
details, please refer to the previous chapter
Physical key control
WP-MAC-E1 The layout of each interface and LCD screen of the education panel
(front) is shown in Figure 3.2
Figure 3.2 diagram of each interface
interface
function
HDMI-IN1
HDMI input 1 channel (input 1 channel)
VGA-IN
VGA input 1 channel (input 1 channel)
USB-IN1
Support mouse, keyboard U disk, mobile phone power
supply, USB3.0
USB-IN2
Support mouse, keyboard U disk, mobile phone power
supply, USB3.0
AUDIO-IN
Audio input (support notebook, computer, mobile phone
and other devices)

12
Tel:[phone] ShenZhenAviation intelligent technology Co, Ltd
Fax:[phone]
Figure 3.1 Interface menu
The specific functions of the display and indicator are shown in table 4.2
Interface / key
function
display screen
display screen
1
input port 1(（VGA-IN1）selection key
2
input port 2（HDMI-IN3）selection key
3
input port 3（HDMI-IN1）selection key
4
input port 4（HDMI-IN2）selection key
5
output port 1（HDMI-OUT1）selection key
6
output port 2（VGA-OUT1）selection key
7
output port 3（HDMI-OUT2）selection key
IR receiver
IR receiver for receiving IR signals from a remote
control
Table 3.2 Specific functions of display screen and indicator light
After opening the WP-MAC-E1 education panel, the LCD display as shown in the
below figure
设备 IP 地址

13
Tel:[phone] ShenZhenAviation intelligent technology Co, Ltd
Fax:[phone]
figure3.3 Power on interface
3.2 signal source switching
WP-MAC-E1 video interfaces are VGA-IN1，HDMI-IN2，HDMI-IN1，HDMI-IN3, VGA-OUT1，
HDMI-OUT2 and HDMI-OUT from left to right
Switch any input channel to any one or more output channels
Just press the cursor on the top left of the touch screen to enter the "video
switching" interface
For example, to switch input channel 2 to output channel 2, just touch and click
HDMI1and HDMI-OUT1 on the screen respectively, and the output interface of the
display screen shows: HDMI-IN1-HDMI-OUT1,then switch can be completed
Fiture 3.4 One input to any one output
3.3 system setting
WP-MAC-E1 education panel supports the system to restore the factory settings.
Select "reset system" in the main menu page, and select "OK" to restart the device.
finally restore the factory setting is complete

14
Tel:[phone] ShenZhenAviation intelligent technology Co, Ltd
Fax:[phone]
Fiture 3.21 Reset system
3.4 RS232/LAN control instruction
When the WP-MAC-E1 education panel is connected with the external control
equipment through RS232 and set, the external control settings can be used for
control operation. The default baud rate of RS232 is 115200bps, 8 data bits, 1 stop
bit and no check bit.
Number
Action
Basic ASCII String
Variables
Switch management instruction
1
Video switching,
input switching to
output or multiple
>Catob,c<CR>
a = input port (1 ~ matrix max port or x < next channel >)
b c= output port (1 ~ matrix maxi port or all)
2
Select the input
video port, combine
with CSWO to use (the
default value of
power on is 0,close)
>CSWI:a<CR>
a = input port (1 ~ max port of matrix)
3
Select the input
video from > CSWI and
switch to output
>CSWO:a<CR>
a = output port (1 ~ matrix max port or all)
4
Query video switching
status (return
correspondence)
#CR<CR>
NULL

15
Tel:[phone] ShenZhenAviation intelligent technology Co, Ltd
Fax:[phone]
5
Save scene
>Sa<CR>
a= scene number (1-6 max)
6
invocation scenario
>Ra<CR>
a = scene number (1-6 max)
7
Set scene name
(Chinese characters
cannot normal
display on WEB)
>SNAMEa:b<CR>
a = scene number (1-6 max)
b = scene name (15 English characters)
8
Query the name of the
scene
#SNAMEa<CR>
a = scene number (1-6 max)
Switching mode
>SW-MODE:a<CR>
a = 0:Auto 1:Autolast 2:Manual
9
USB switch command
>USB:a<CR>
a = 1(usb input1) or 2(usb input2)
EDID management instruction
1
Switch EDID, output
switch to input
>EDIDatob<CR>
a = input port (1 ~ max port of matrix)
b = output port (1 ~ matrix max port or all)
2
Switch to EDID and
switch to input in the
system
>SYSEatob<CR>
a = system number (1 ~ 6)
b = output port (1 ~ matrix max port or all)
3
Save the EDID and
switch the output to
the internal system
>SOEDatob<CR>
a = output port (1 ~ matrix max port or all)
b = system number (1 ~ 6)
4
Save the EDID and
switch the input to
the internal system
>SIEDatob<CR>
a = output port (1 ~ matrix max port or all)
b= system number (1 ~ 6)
Sub card management instruction
1
Set port name of sub
card
>PORT_NAME:a,b<CR>
a = sub card port (1 ~ max port of matrix)
b = port name
2
Query the port name of
the sub card
#PORT_NAME:a<CR>
a= sub card port (1 ~ max port of matrix)
3
Set forced output
HDMI / DVI format
>HDMODE:a,b<CR>
a = output port (1 ~ max port of matrix)
b = 0:DVI 1:HDMI
4
Set audio embed and
external embed
>AUMODE:a<CR>
a = 0: embedded 1: external embedded

16
Tel:[phone] ShenZhenAviation intelligent technology Co, Ltd
Fax:[phone]
5
Setting DIV-M input
format
>DIVM-FORMAT:a<CR>
a = 0:AUTO 1:CVBS 2:YPBPR 3:VGA 4:DVI
5
Set DIV-M output
resolution
>DIVM-RES:a<CR>
a = resolution number
0:1024x768P60
1:1360x768P60
2:1920x1200P60
3:720P60
6:1080P50
7:1080P60
6
Set the resolution of
the output scaler sub
card
>SCALER_RES:a,b<CR>
a = sub card port (1 ~ max port of matrix)
b = resolution number
7
Set the video
properties of the
output scaler sub
card
>SCALER_ATTR:a,b:c<C
R>
a = sub card port (1 ~ matrix max port)
b = option (0 = brightness 1 = capability 2 = contract 3 = sharpness)
c = value(0~99)
HDCP management instruction
1
Set the HDCP of the
input sub card
>HDCPIN:a,b<CR>
a = input port (1 ~ max port of matrix)
b = 0:OFF 1:ON
2
Set the default HDCP
state of the output sub
card, depending on the
input source
>HOUTNM:a<CR>
a= output port (1 ~ matrix max port or all, code: 0)
3
Set output sub card
HDCP on
>HOUTON:a<CR>
a = output port (1 ~ matrix max port or all, code: 1)
4
Set the output sub card
HDCP off (hdcp2.2 does
not support closing)
>HOUTOFF:a<CR>
a = output port (1 ~ matrix max port or all, code: 2)
5
Query all input HDCP
status
#AHDCPIN:a<CR>
a = query type (0 = input source HDCP, 1 = set state)
6
Query all output HDCP
status
#AHDCPOUT:a<CR>
a = query type (0 = output source HDCP, 1 = set state)
Wireless projection management instruction
1
Disconnect the
projection
connection
>MIR:a<CR>
a = Disconnect\Restart\Power
2
Send screen control
key value
>MIR-KEY:a<CR>
a = key (see table)