Cuisinart SSB-1HK User manual

SSB1U
INSTRUCTION BOOKLET
Cuisinart
®
Hot & Cold Blender
For your safety and continued enjoyment of this product, always read the instruction book carefully before using.
SSB-1HK
Recipe
Booklet
Reverse Side

2
IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions should always be followed including
the following:
1. READ ALL INSTRUCTIONS, PRODUCT LABELS AND WARNINGS BEFORE USING
THIS HOT & COLD BLENDER.
2. Do not touch hot surfaces; carry the unit by handles. Always use oven mitts when handling
hot material, and allow metal parts to cool before cleaning. Allow the Hot & Cold Blender
to cool thoroughly before putting in or taking off parts.
3. When unit is not in use and before cleaning, unplug the Hot & Cold Blender from wall
outlet. Let the Hot & Cold Blender cool down thoroughly before assembling or
disassembling it.
4. To protect against risk of electrical shock, do not immerse the appliance or plugs in water
or other liquids.
5. Close supervision is always necessary when this or any appliance is used near children or
incapacitated persons.
6. Do not allow anything to rest on the power cord. Do not plug in cord where people may
walk or trip on it. Unplug this Hot & Cold Blender from the wall outlet before you go out for
a trip or long excursion.
7. Do not operate this or any appliance with a frayed or damaged cord, or plug, or after the
appliance malfunctions or is dropped or has been damaged in any manner. Take appliance
to the nearest authorized service facility for examination, repair or electrical or mechanical
adjustment.
8. Do not let the cord dangle over the edge of a table or counter or touch hot surfaces. Do
not place on an unsteady or cloth-covered surface.
9. Avoid contact with moving parts.
10. Do not use attachments not recommended by the manufacturer. They may cause fire,
electric shock or injury.
11. Do not use outdoors or for commercial purposes.
12. Do not place the appliance near a hot gas or electric burner, or in a
heated oven.
13. Keep power cord away from the hot surface of this Hot & Cold Blender. Do not put any
flammable object on the hot surface of this Hot & Cold Blender.
14. Place this Hot & Cold Blender a minimum of 5cm away from wall or any other object.
15. Do not use this Hot & Cold Blender for other than its intended use.
16. When plugging or unplugging this Hot & Cold Blender, be sure not to touch
the plug blades with your fingers.
17. If electric circuit is overloaded with other appliances, your Hot & Cold Blender may not
operate properly. This Hot & Cold Blender should be operated on a separate electrical cir-
cuit from other operating appliances.
18.
Extreme caution must be used when moving an appliance containing hot oil or other hot liquids.
19. Always attach plug to appliance first, then plug cord into the wall outlet. To disconnect, turn
any control to “off”, then remove plug from wall outlet.

3
20. This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning use of the appliance by a per
son responsible for their safety.
21. Children should be supervised to ensure that they do not play with the appliance.
22. Appliances are not intended to be operated by means of an external timer or separate
remote-control system.
23. CAUTION: Ensure that the blender is switched off before removing it from the stand.
Blade is very sharp. Handle with care.
SAVE THESE INSTRUCTIONS
FOR HOUSEHOLD USE ONLY
CONTENTS
Product Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
The Hot & Cold Blender . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
A Glass Jar Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
- Fitting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . 5
- Removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . 5
B Lid & Measuring Cup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . 5
C Control Panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . 6
- Power Button
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
- Timer Control
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
- Temperature Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . 6
- Stir Button
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
- Blending Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
D Making Soup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . 7
E Blending Cold Ingredients
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
F Hints & Tips. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . 8
Care & Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . 9
Self Clean Feature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . 9
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

4
PRODUCT DESCRIPTION
Lid with removable measuring cup
On/Off
Motor Base
Glass Jar Assembly includes:
Glass Jar
1750 ml (Cold Use) / 1400 ml (Soup Use)
Non-Stick Heating Plate
Jar Collar
Stir Button
Blending Control
Heat Control
Timer Control
Non-Slip Rubber Feet

5
THE HOT & COLD BLENDER
A Glass Jar Assembly
Before first use, clean the glass jar thoroughly (see cleaning & maintenance section for more
information).
The glass Jar assembly is one complete unit which includes glass jar, handle, cooking plate
and collar.
Fitting
Position jar unit on the motor base so that the arrow on the jar collar is level with the arrow on
the housing unit (fig. 1). Push the jar down into place (fig. 2).
N.B. Take care when placing the glass jar assembly on the motor base as incorrect positions
may damage the interlock switches.
Removing
Switch the Hot & Cold Blender off and unplug from the mains outlet. Lift the Glass Jar
Assembly up and away from the motor base, holding the handle only. Do not twist the jar.
Caution: The heating element is hot when the Hot & Cold Blender is in heat mode, do not
touch the underside of the collar.
B LID & MEASURING CUP
To remove the lid from the glass jar assembly, grip the edges of the lid firmly with one hand
and lift upwards. When you have added the required food to the blender jar, place lid on jar
before heating and blending. To replace, simply position over the jar and press down firmly
(ensure the pouring spout on the jar is covered by the protrusion on the lid).
To remove the measuring cup from the lid, lift up and away. To replace, position the cup over
the lid, aligning with the corresponding grooves in the lid.
fig. 1 fig. 2
Glass Jar
Assembly
Motor
Base

6
WARNING: Steam will escape around the measuring cup when the Hot & Cold Blender is in
heat mode, this is normal, but handle with care – steam can burn. Always ensure the lid and cup
are replaced before blending.
C CONTROL PANELS
Power Button
Plug the Hot & Cold Blender into the mains outlet, the power button (on/off) will flash. Press
once and the light will become static; the Hot & Cold Blender is now in ‘stand-by’ mode.
If the on/off button is pressed whilst in ‘stand-by’ mode, the Hot & Cold Blender will revert
back to dormant with the on/off button flashing. Any settings entered will be cancelled.
The only way to turn the flashing on/off button off is to unplug the Hot & Cold Blender from
the mains.
Timer Control
When the Hot & Cold Blender is in ‘stand-by’ mode the cooking time can be set by either
pressing the + or - buttons, if the ‘-’ button is pressed at this stage, 30 minutes will be dis-
played on the digital display, this is the maximum cooking time. If the ‘-’ button is pressed at
any other time, the cooking time will be reduced in one minute increments.
The ‘+’ button increases the cooking time in 1 minute increments.
N.B. Pressing any of the buttons will be accompanied by an audible sound.
N.B. The cooking time can be increased or decreased by pressing the ‘+’ and ‘-’ buttons at any
time during the heating or cooking cycle.
Temperature Control
The Hot & Cold Blender will start its heating or cooking cycle when the temperature is
selected to either high, low or simmer.
N.B. The temperature can be changed at any time during the heating or cooking cycle.
Stir Button
The stir function can be operated at any time during the heating or cooking cycle, it can also
be operated in ‘stand-by’ mode when ingredients are being added to the glass jar.
It is recommended that you use the stir function while frying or sautéing onions, garlic or other
base ingredients at the start of your recipe.
It is not ideal to use the stir button to blend the soup but it can be used if you require chunky
soup.
Blending Control
The blending control runs from 1, a low speed, through to 4, the highest speed. Select desired
speed by twisting the dial clockwise, reduce speed by twisting the dial anticlockwise, or pulse
twisting the dial to the ‘pulse’ setting.
For safety, the blending control only works when the cooking or heating process has com-
pleted.

7
The heater can also manually be turned off by pressing the heat button currently in use (this
will be illuminated) or alternatively pressing the on/off (power button).
If the on/off power button is used to turn off the heater, the Hot & Cold Blender will switch off
completely and will have to be re-started for blending.
If you are blending hot ingredients do not exceed speed 2; speed 1 is sufficient.
When blending cold ingredients, start at low speed and increase up to level 4 until desired
consistency is reached.
N.B. Do not blend for longer than three minutes. This is the maximum running time for the
motor.
D MAKING HOT SOUP
Place the motor base onto a flat, sturdy surface.
Position the Glass Jar Assembly onto the motor base and plug into a suitable mains outlet.
Press the on/off button to set the Hot & Cold Blender to ‘standby’ mode.
Select the required time, this can be adjusted throughout the cooking process, but a time
must be selected to start the heater initially.
To fry ingredients such as onions or garlic, add butter or oil first before switching on heat
mode.
Make sure you place the butter on the heating plate rather than the blades. Select low heat
setting to melt butter. If frying onions and garlic, add and cook until softened, replacing lid.
The appliance may smoke a little and release a slight odour during first use, this is normal.
To mix the onions or garlic, use the stir button on the control panel.
Add the remaining ingredients (vegetables, stock and seasoning etc) and set on a high heat
and bring to the boil.
When making soup, only fill the contents of the glass jar to 1400 ml mark. Once boiled reduce
heat to simmer, set timer and leave to cook.
N.B. The heater works with a thermostat and so heat will increase or decrease accordingly and
bubbles will become bigger or smaller during cooking.
When cooking time has finished the Hot & Cold Blender will beep 4 times.
To blend soup, use the blending control; this can only be used once the heat mode and
timer has been exited. When ready, simply blend soup on level 1 until desired consistency is
achieved and serve.
Warning: When cooking or blending with hot liquid it is essential the lid and cup are left on the
blender to prevent harm to self.
E BLENDING COLD DRINKS
The blender can also be used as a standard blender. Also good for blending cold ingredients,
crush ice, clips and dressings.
Place the motor base onto a flat, sturdy surface.
Position the Glass Jar Assembly on the base and plug into a suitable mains outlet.

8
Add all necessary ingredients into the glass jar and replace the lid. You may add more ingre-
dients during blending by lifting the measuring cup in the lid and dropping ingredients through
the opening in the lid.
N.B. The maximum fill for cold ingredients is 1750 ml.
Turn the blender control dial to your desired speed or use the pulse function. Turn the blender
control dial to ‘off’ when the desired consistency is reached.
Unplug the appliance immediately after use.
Do not store food or liquid in the glass jar. Empty and clean thoroughly after use.
Do not overload the Hot & Cold Blender. If the motor stalls, turn the Hot & Cold Blender off
immediately, unplug the unit and carefully remove a portion of the food, then continue.
F HINTS & TIPS
Add butter or oil to heating plate and allow to melt before frying vegetables.
If soup recipes call for cheese or cream to be added at the end of the recipe, don’t allow to
boil. Most soup will actually be hot enough to melt the cheese using just the stir function
rather than adding more heat.
To make low fat soups, use low fat fromage frais instead of crème fraîche or soured cream.
If your soup is too thick, thin with a little water or semi-skimmed milk when blending. Do not
exceed 1.4L.
If you are making tomato soup and your tomatoes are too pale or under ripe, add 1tbsp of
tomato purée to add colour and flavour.
Cut most foods into cubes approximately 1.5-2.5cm to achieve a more uniform result. Cut all
cheese into pieces no larger than 1.5cm.
Use measuring cup in the lid to measure liquid ingredients such as alcohol. Always replace
after ingredients have been added.
When chopping fresh herbs, garlic, onion, zest, breadcrumbs, nuts and spices make sure the
glass jar and blades are completely dry.
If food tends to stick to the sides of the glass jar when blending, pulse in short bursts.
Pulses should be short bursts. Space the pulses so the blades stop rotating between pulses.
Don’t over process foods. This appliance will achieve most desired results in seconds not
minutes.
For frozen drinks, chill all ingredients before blending.
If foods do not seem to be blending smoothly, use the pulse function to chop then blend con-
tinuously.
Ensure you add oil or butter to the non-stick plate before you turn the heater on.
If in any doubt about what’s happening, switch off the Hot & Cold Blender and refer to this IB.

9
CARE & MAINTENANCE
Always unplug the appliance from the mains outlet before cleaning.
Before first use and after every use, clean each part thoroughly.
Periodically check all parts before reassembly. If any part is damaged or jar is chipped or
cracked, DO NOT USE THE HOT & COLD BLENDER.
CAUTION: Blade is very sharp. Handle with care.
To clean the complete Glass Jar Assembly (glass jar, cooking plate and collar) follow ‘Self
Clean Feature’ below or wash in a bowl of hot soapy water.
To clean the lid and measuring cup, wash in hot soapy water.
Wipe the motor base clean with a damp cloth to remove any residue, and dry thoroughly. Do
not use abrasive cleaners on the housing base. Apply any cleaning agent to the cloth, not the
base.
Never submerge the motor base in water or other liquid, or place in a dishwasher.
Make sure all the parts are clean and dry before storing.
Never wrap the cord around the outside of the Hot & Cold Blender.
Never immerse the plug, lead or housing in water or any other liquid.
Never immerse the glass jar in water straight after heating; allow it to cool down first.
SELF CLEAN FEATURE
To clean the Hot & Cold Blender quickly and easily, simply add approximately 0.5L of water
and a little washing up liquid to the glass jar. Set the timer for two minutes and press the
simmer button. When the water is hot turn the heater off; blend liquid on speed 1 for 1
minute. Repeat using clean water. This may help release any food that maybe on the
underside of the blades. Alternatively, wash the glass jar in warm soapy water. Rinse and dry
thoroughly.
Ensure the glass jar is thoroughly dry before use.

10
WARRANTY
Three-Year Limited Warranty
This warranty supersedes all previous warranties on the Cuisinart
®
Hot & Cold Blender. This
warranty is available to consumers only. You are a consumer if you own a Cuisinart
®
Hot & Cold
Blender that was purchased at retail for personal, family, or household use. This warranty is not
available to retailers or other commercial purchasers or owners. We warrant that your Cuisinart
®
Hot & Cold Blender will be free of defects in material or workmanship under normal home use
for three years from the date of original purchase. We suggest that you complete and return
the enclosed product registration card promptly to facilitate verification of the date of original
purchase. However, return of this product registration card does not eliminate the need for the
consumer to maintain the original proof of purchase in order to obtain the warranty benefits. In
the event that you do not have proof of purchase, the purchase date for purposes of this war-
ranty will be the date of manufacture.
If your Cuisinart
®
Hot & Cold Blender should prove to be defective within the warranty period,
we will repair it, or if we think necessary, replace it. To obtain warranty service, please register
your warranty online at
www.cuisinart.com.hk
for warranty registration.
Conair Far East Ltd. Customer Service Center:
35/F., Standard Chartered Tower, Millennium City 1,
388 Kwun Tong Road, Kwun Tong, Kowloon, Hong Kong
Customer Service Hotline: [phone]
Notice: Chinese version is taken as standard for guarantee period and specifications.
This warranty expressly excludes any defects or damages caused by accessories, replacement
parts, or repair service other than those that have been authorized by Cuisinart.
This warranty does not cover any damage caused by accident, misuse, shipment or other than
ordinary household use.

11

SAVOR THE GOOD LIFE
©2010 Cuisinart
Conair Far East Ltd.,
A subsidiary of Conair Corporation USA
Conair Corporation USA,
1 Cummings Point Road, Stamford,
Connecticut 06902 USA
Conair Far East Ltd., 35/F.,
Standard Chartered Tower,
Millennium City, 388 Kwun Tong Road,
Kwun Tong, Kowloon, Hong Kong
Printed in China
IB-9/426
Cuisinart offers an extensive assortment of top quality products to make life in the
kitchen easier than ever. Try some of our other countertop appliances and
cookware, and Savor the Good Life.
www.cuisinart.com.hk
Coffeemakers Food
Processors
Toaster Blenders Cooker Ice Cream
Makers
IB-10/222