Cuisinart GAS0356AS User manual

Twin Oaks Dual Function Grill
Model GAS0356AS / GAS0356ASO
ASSEMBLY INSTRUCTIONS

1
ASSEMBLY INSTRUCTIONS:
READ ALL SAFETY WARNINGS & ASSEMBLY INSTRUCTIONS CAREFULLY
BEFORE ASSEMBLING OR OPERATING YOUR GRILL.
WE RECOMMEND TWO PEOPLE WORK TOGETHER WHEN ASSEMBLING THIS UNIT.
The following tools are required to assemble this Cuisinart Twin Oaks Pellet Grill:
• Phillips Screwdriver
• Pliers or Wrench
PARTS LIST:
1 Top Front Panel
1 Bottom Front Panel
1 Right Front Leg
1 Left Front Leg
1 Right Side Front Panel
1 Left Side Front Panel
1 Left Side Panel
1 Cart Brace
1 Cart Base
1 Left Rear Leg
1 Back Panel
1 Right Rear Leg
1 Grill Body
2 Hood Handles
1 Control Knob
1 Griddle
1 Side Burner Grate
1
2
3
4
5
6
7
8
11
9
10
12
1 Right Side Table
1 Left Side Control Panel
1 Right Side Control Panel
1 Grease Cup
2 Warming Racks
1 Ash Catcher
4 Casters
4 Cooking Grates
1 Cord Wrap
1 Heat Baffle
1 Heat Plate
3 Heat Tents
1 Grease Tray
1 Auger Housing
2 Accessory Hooks
1 Tank Block Bar
15
16
17
18
19
20
21
22
31
29
30
32
13
14
33
Note: Most hardware is pre-attached to the grill. You may need to loosen some screws
partially while others may need to be removed in order to assemble parts. The screws that
you remove will be re-used so don’t misplace this hardware.
Extra screws are included in a small bag with the owners manual.
25
23
24
26
27
28

2
31
30
29
32
25
27
9
23
22
19
16
20
17
14
13
12
18
10
21
6
1
11
7
33
24
28
26
15
4 3
5
8
2

3
Step 2
• Loosen 6 screws 3-4
turns on FRONT LEGS
3and 4
• Do not remove screws
• Attach FRONT PANELS
1and 2using keyholes
• Tighten 6 screws
3
NOTE: Before tightening keyhole
screws, make sure panels are aligned.
• Remove 2 screws
• Attach FRONT PANELS
1and 2
• Tighten 2 screws
Step 1
1
2
1
4
2

4
• Loosen 2 screws
• Attach LEFT SIDE
PANEL 7
• Tighten 2 screws on
LEFT SIDE PANEL 7
Step 4
• Loosen 6 screws 3-4
turns on FRONT LEGS
3and 4
• Do not remove screws
• Attach RIGHT SIDE
FRONT PANEL 5and
LEFT SIDE FRONT
PANEL 6
• Tighten 6 screws on
RIGHT SIDE FRONT
PANEL 5and LEFT
SIDE FRONT PANEL 6
Step 3
5
6
5
4
1
1
3
34
2
2
6
7

5
• Attach CART BASE 9
• Tighten 4 screws
(Removed from
Step 5)
Step 6
• Loosen 2 screws
• Attach CART BRACE 8
• Tighten 2 screws on
CART BRACE 8
• Remove 4 screws
Step 5
Remove 2 screws Remove 2 screws
6
5
4
1
3
7
1
5
4
3
8
2
2
8
9
6
7

6
• Loosen 9 screws on
REAR LEGS 10 and 12
• Attach BACK PANEL 11
to REAR LEGS 10 and
12
• Tighten 5 screws
• Remove 4 screws
• Attach CART BASE 9to
rear legs
• Tighten 4 screws
(Removed from Step 7)
Remove 2 screws Remove 2 screws
Step 7
Step 8
10
12
11
11
9
12
10

7
• Lock CASTERS 24
• Attach CASTERS 24 to
legs
Step 10
CASTERS
locked
unlocked
• Attach LEFT SIDE
PANEL 6and CART
BRACE 8
• Tighten 4 screws
Step 9
8
Tighten
4 screws
24
7

8
ACCESSORY
HOOKS
• Attach ACCESSORY
HOOKS 32 to LEFT
SIDE PANEL 7with
wing nuts
Step 11
• Loosen 2 screws
• Install TANK BLOCK
BAR 33
• Tighten screws
Step 12
32
7
33

99
• Loosen 5 screws
• Remove 2 screws
Remove 2 screws
Step 14
Step 13
Loosen 5 screws
• Loosen 1 screw
• Remove 2 screws
Loosen 1 screw Remove 2 screws

Step 15
Step 16
CART BRACKETS
• Set GRILL BODY 13 on
cart
• Make sure screw drops
into rear cart brackets
• Push GRILL BODY 13 to
back of cart
• Install 2 screws in FRONT
BRACKETS (Removed
from Step 13 and Step
14)
• Tighten 4 screws on cart
brackets (2 screws left
over will be used in future
steps)
10
CART BRACKETS
13
• Install HOOD HANDLES
14 (Wing nuts, bezels and
washers are pre-installed
on handles)
14

11
• Attach RIGHT SIDE
TABLE 18 to GRILL
BODY 13 using keyholes
• Do not tighten screws at
this time
• Install and tighten 2
screws (Removed from
Step 13 and Step 17)
Step 18
• Loosen 2 screws
• Attach RIGHT SIDE
CONTROL PANEL 20 to
RIGHT SIDE TABLE 18
using keyholes
• Tighten 2 screws
• Remove 2 screws and
washer
Step 17
Loosen
screws
18
20
18
13
Remove
screw and
washer
Remove
screw
Install
screws

12
Step 20
• Install screw and washer
(Removed from Step 17)
• Make sure control panels
are aligned
• Tighten 5 screws from
Step 18 and Step 19
Step 19
Align
Panels
• Remove WING NUT and
SIDE BURNER
• Loosen 2 screws from
SIDE BURNER
VALVE A
• Install SIDE BURNER
VALVE using keyholes in
RIGHT SIDE CONTROL
PANEL 20 and tighten
screws B
• Install SIDE BURNER
and make sure BURNER
VENTURI ts over VALVE
NOZZLE C
• Tighten WING NUT C
20
Loosen 2
screws
BURNER
VENTURI
VALVLE
NOZZLE
WING
NUT
Install
screw and
washer
A
B
C

13
Step 22
Step 21
• Attach CONTROL
KNOB 15
15
• Attach ELECTRODE
WIRE to IGNITOR

14
Step 24
• Loosen 2 screws from
LEFT SIDE CONTROL
PANEL 19
• Remove 1 screw
Step 23
19
19
• Attach LEFT SIDE
CONTROL PANEL 19 to
PELLET HOPPER using
keyholes
Remove
screw

15
• Remove 4 screws and
washers from AUGER
HOUSING 31
• Loosen 1 screw
Step 26
Step 25
Loosen
screw
Remove
4 screws
31
• Install and tighten 2
screws (Removed from
Step 14 and Step 23)

16
• Install AUGER HOUSING
31 using keyhole in
rebox and slots in pellet
hopper bracket
• Tighten 5 screws and
washers in rebox
Step 27
• Remove 2 screws
• Attach CORD WRAP 26
using 2 screws
Step 28
31
26

17
• Once connected, twist to
tighten
Step 29b
• Connect wiring for
Controller and Pellet
Sensor
• These wires can only be
connected one way
• Make sure the connectors
are lined up properly
before tightening
Step 29a
• Secure wiring with cord
clip.
Step 29c

18
• Attach HEAT BAFFLE 27
Step 31
Step 30
27
• Install SIDE BURNER
GRATE 17
17

19
Step 33
• Install HEAT TENTS 29
above each burner
Step 32
29
• Install HEAT PLATE 28
on welded brackets
28