Cuisinart SMK0036AS User manual

Woodcreek
4-in-1 Pellet Grill
Model SMK0036AS / SMK0036ASO
ASSEMBLY INSTRUCTIONS

1
ASSEMBLY INSTRUCTIONS:
READ ALL SAFETY WARNINGS & ASSEMBLY INSTRUCTIONS CAREFULLY
BEFORE ASSEMBLING OR OPERATING YOUR GRILL.
WE RECOMMEND TWO PEOPLE WORK TOGETHER WHEN ASSEMBLING THIS UNIT.
The following tools are required to assemble this Cuisinart Woodcreek 4-in-1 Pellet Grill:
• Phillips Screwdriver
• Pliers or Wrench
PARTS LIST:
1 Top Front Panel
1 Bottom Front Panel
1 Right Front Leg
1 Left Front Leg
1 Right Side Panel
1 Left Side Panel
1 Cart Brace
1 Cart Base
1 Left Rear Leg
1 Back Panel
1 Right Rear Leg
1 Grill Body
1 Hood Handle
1 Temperature Gauge
1 Temperature Gauge Bezel
1 Control Knob
1 Pellet Hopper Lid Handle
1 Pellet Hopper
1
2
3
4
5
6
7
8
11
9
10
12
1 Left Side Table
1 Right Side Control Panel
1 Left Side Control Panel
2 Grease Cup Brackets
1 Grease Cup
1 Warming Rack
1 Ash Catcher
1 Grease Channel
3 Cooking Grates
1 Cord Wrap
1 Heat Baffle
1 Left Side Heat Plate
1 Right Side Heat Plate
1 Auger Housing
4 Accessory Hooks
1 Ceramic Insert
1 Charcoal Tray
1 Cast Iron Griddle
4 Casters
15
16
17
18
19
20
21
22
31
29
30
32
13
14
33
34
Note: Most hardware is pre-attached to the grill. You may need to loosen some screws
partially while others may need to be removed in order to assemble parts. The screws that
you remove will be re-used so don’t misplace this hardware.
Extra screws are included in a small bag with the owners manual.
25
23
24
26
27
28
35
36
37

2
31
30
29 32
25
27
9
23
22
19
16
20
17
14
13
12 18
10
21
6
1
11 7
33
24
28
26
15
435
34
35
8
36
37
2

3
• Loosen 6 screws 3-4
turns on FRONT LEGS
3and 4
• Do not remove screws
• Attach FRONT PANELS
1and 2using keyholes
• Tighten 6 screws
3
NOTE: Before tightening keyhole
screws, make sure panels are aligned.
• Remove 2 screws
• Attach FRONT PANELS
1and 2
• Tighten 2 screws
Step 2
1
2
1
4
2
Step 1

4
Step 3
• Loosen 3 screws
• Attach RIGHT SIDE
PANEL 5
• Tighten 3 screws on
RIGHT SIDE PANEL 5
Step 4
5
1
3
4
2
• Loosen 2 screws
• Attach LEFT SIDE
PANEL 6
• Tighten 2 screws on
LEFT SIDE PANEL 6
6
5
4
1
3
2

5
• Attach CART BASE 8
• Tighten 4 screws
(Removed from
Step 5)
• Loosen 2 screws
• Attach CART BRACE 7
• Tighten 2 screws on
CART BRACE 7
• Remove 4 screws
Step 6
Remove 2 screws Remove 2 screws
6
5
4
1
3
7
1
54
3
8
2
2
Step 5

6
• Loosen 8 screws on
REAR LEGS 9and 11
• Attach BACK PANEL 10
to REAR LEGS 9and
11
• Tighten 4 screws
• Remove 4 screws
Remove 2 screws Remove 2 screws
Step 7
Step 8
10
9
11
• Attach CART BASE 8to
rear legs
• Tighten 4 screws
(Removed from Step 7)
8
9
11 10

7
• Lock CASTERS 37
• Attach CASTERS 37 to
legs
CASTERS
locked
unlocked
• Attach LEFT SIDE
PANEL 6and CART
BRACE 7
• Tighten 4 screws
Step 10
6
Tighten
4 screws
37
7
Step 9

8
ACCESSORY
HOOKS
• Attach ACCESSORY
HOOKS 33 to LEFT
SIDE PANEL 6and
CART BRACE 7with
wing nuts
Step 11
Step 12
33
6
7
• Loosen 1 screw
• Remove 2 screws
Remove 2 screws Loosen 1 screw

Step 14
CART BRACKETS
• Set GRILL BODY 12 on
cart
• Make sure screw drops
into rear cart brackets
• Push GRILL BODY 12 to
back of cart
• Install 2 screws in
FRONT BRACKETS
(Removed from Step 12
and Step 13)
• Tighten 4 screws on cart
brackets (2 screws left
over will be used in future
steps)
• Loosen 5 screws
• Remove 2 screws
Loosen 5 screws
Remove 2 screws
CART BRACKETS
12
Step 13
9