Cuisinart SMK1021ASO User manual

Bristol 21” Pellet Grill
Model SMK1021ASO
ASSEMBLY INSTRUCTIONS
WARNING
READ ALL INSTRUCTIONS BEFORE INSTALLATING AND USING
APPLIANCE. FAILURE TO FOLLOW THESE INSTRUCTIONS COULD
RESULT IN PROPERTY DAMAGE, BODILY INJURY OR EVEN
DEATH. CONTACT LOCAL BUILDING OR FIRE OFFICIALS ABOUT
RESTRICTIONS AND INSTALLATION INSPECTION REQUIREMENTS
IN YOUR AREA. SAVE THESE INSTRUCTIONS.
NOTICE TO INSTALLER:
LEAVE THESE INSTRUCTIONS
WITH THE GRILL OWNER
FOR FUTURE REFERENCE.

1
ASSEMBLY INSTRUCTIONS:
READ ALL SAFETY WARNINGS & ASSEMBLY INSTRUCTIONS CAREFULLY
BEFORE ASSEMBLING OR OPERATING YOUR GRILL.
WE RECOMMEND TWO PEOPLE WORK TOGETHER WHEN ASSEMBLING THIS UNIT.
The following tools are required to assemble this Cuisinart 21” Pellet Grill:
• Phillips Screwdriver
• Pliers or Wrench
PARTS LIST:
1 Front Panel
1 Right Front Leg
1 Left Front Leg
1 Right Side Panel
1 Left Side Panel
1 Cart Brace
1 Cart Base
1 Left Rear Leg
1 Back Panel
1 Right Rear Leg
1 Grill Body
1 Hood Handle
1 Temperature Gauge
1 Temperature Gauge Bezel
1 Control Knob
1 Pellet Hopper Lid Handle
1 Pellet Hopper
1 Left Side Table
1
2
3
4
5
6
7
8
11
9
10
12
1 Right Side Control Panel
1 Left Side Control Panel
1 Grease Cup Bracket
1 Grease Cup
1 Warming Rack
1 Ash Catcher
1 Grease Channel
2 Cooking Grates
1 Cord Wrap
1 Heat Baffle
1 Heat Plate
1 Auger Housing
2 Accessory Hooks
4 Casters
15
16
17
18
19
20
21
22
31
29
30
32
13
14
Note: Most hardware is pre-attached to the grill. You may need to loosen some screws
partially while others may need to be removed in order to assemble parts. The screws that
you remove will be re-used so don’t misplace this hardware.
Extra screws are included in a small bag with the owners manual.
25
23
24
26
27
28

2
30
29
28
31
24
26
8
22
21
18
15
19
16
13
12
11
17
9
20
5
1
10
6
32
23
27
25
14
324
7

3
• Loosen 6 screws 3-4
turns on FRONT LEGS
2and 3
• Do not remove screws
• Attach FRONT PANEL
1using keyholes
• Tighten 6 screws
2
NOTE: Before tightening keyhole
screws, make sure panels are aligned.
• Loosen 3 screws
• Attach RIGHT SIDE
PANEL 4
• Tighten 3 screws on
RIGHT SIDE PANEL 4
4
Step 2
1
3
1
23
Step 1

4
Step 3
Step 4
• Loosen 2 screws
• Attach LEFT SIDE
PANEL 5
• Tighten 2 screws on
LEFT SIDE PANEL 5
5
43
1
2
• Loosen 2 screws
• Attach CART BRACE 6
• Tighten 2 screws on
CART BRACE 6
• Remove 4 screws
Remove 2 screws Remove 2 screws
5
43
1
2
6

5
• Attach CART BASE 7
• Tighten 4 screws
(Removed from
Step 4)
• Loosen 8 screws on
REAR LEGS 8and 10
• Attach BACK PANEL 9
to REAR LEGS 8and
10
• Tighten 4 screws
• Remove 4 screws
Remove 2 screws
Remove 2 screws
9
Step 6
1
43
2
7
810
Step 5

6
Step 7
Step 8
• Attach CART BASE 7to
rear legs
• Tighten 4 screws
(Removed from Step 6)
7
9
• Attach LEFT SIDE
PANEL 5and CART
BRACE 6
• Tighten 4 screws
5
Tighten
4 screws
6

7
ACCESSORY
HOOKS
• Lock CASTERS 32
• Attach CASTERS 32 to
legs
• Attach ACCESSORY
HOOKS 31 to LEFT
SIDE PANEL 5with
wing nuts and washers
CASTERS
locked
unlocked
Step 10
32
31
6
Step 9

Remove 4 screws
Loosen 1 screw
8
Step 11
Step 12
• Loosen 1 screw
• Remove 4 screws
• Remove protective plate
from right side of grill
body assembly
• Loosen 5 screws
• Remove 3 screws
• Remove two protective
plates from left side of
grill body assembly
Loosen 5 screws
Remove 3 screws

Step 14
CART BRACKETS
• Set GRILL BODY 11 on
cart
• Make sure screw drops
into rear cart brackets
• Push GRILL BODY 11 to
back of cart
• Install 2 screws in
FRONT BRACKETS
(Removed from Step 11
and Step 12)
• Tighten 4 screws on cart
brackets (2 screws left
over will be used in future
steps)
CART BRACKETS
11
• Remove 4 screws
from GREASE CUP
BRACKET 21
• Install GREASE CUP
BRACKET 21 to the
bottom of the GRILL
BODY 11 using 4 screws
21
11
Step 13
9