Cuisinart GAS9456AS User manual

Deluxe Four Burner Gas Grill
Model GAS9456AS / GAS9456ASO
ASSEMBLY INSTRUCTIONS

1
ASSEMBLY INSTRUCTIONS:
READ ALL SAFETY WARNINGS & ASSEMBLY INSTRUCTIONS CAREFULLY
BEFORE ASSEMBLING OR OPERATING YOUR GRILL.
WE RECOMMEND TWO PEOPLE WORK TOGETHER WHEN ASSEMBLING THIS UNIT.
The following tools are required to assemble this Cuisinart 4 Burner Gas Grill:
• Phillips Screwdriver
Note: Most hardware is pre-attached to the grill. You may need to loosen some screws
partially while others may need to be removed in order to assemble parts. The screws that
you remove will be re-used so don’t misplace this hardware.
Extra screws are included in a small bag with the owners manual.
PARTS LIST:
1 Front Right Leg
1 Front Panel
1 Front Left Leg
1 Side Panel
1 Left Side Panel
1 Cart Brace
1 Cart Base
1 Left Rear Leg
1 Back Panel
1 Right Rear Leg
1 Side Burner Grate
4 Heat Tents
1 Side Burner Knob
1 Right Side Control Panel
1 Grease Cup
1 Warming Rack
1 Heat Shield
1 Right Side Table
1 Left Side Table
1 Grill Body
1 Left Side Control Panel
4 Casters
3 Cooking Grates
1 Grease Tray
1 Bar
1
2
3
4
5
6
7
8
11
9
10
12
13
14
15
16
17
18
19
20
21
22
23
24
25

2
20
19 18
21 14
16
23
12
11
15
13
8
596
17
3
2
1
7
4
24
10
22
25

3
Step 1
• Loosen 6 screws
3-4 turns
• Do not remove
screws
• Attach FRONT
PANEL using
keyholes
• Tighten 6 screws
• Loosen 3 screws
• Attach SIDE
PANEL
• Tighten 3 screws
on SIDE PANEL
Step 2
FRONT PANEL
SIDE PANEL
123
4123
2
4
4
NOTE: Before tightening keyhole
screws, make sure panels are aligned.

4
• Loosen 2 screws
• Attach LEFT
SIDE PANEL
• Tighten 2 screws
on LEFT SIDE
PANEL
• Remove 6 screws.
• Attach CART
BRACE.
• Tighten two
screws on CART
BRACE.
Remove 2 screws Remove 2 screws
Step 3
Step 4
LEFT
SIDE
PANEL
CART BRACE
1 2 3
5
1 2 3
5
6
5
5
6
6

5
• Attach CART BASE
• Make sure TANK
• BRACKETS are on this
end. (See drawing below)
• Tighten 4 screws
(Removed from Step 4)
• Loosen 6 screws
• Attach BACK
PANEL
• Tighten 4 screws
• Remove 6 screws
Remove 2 screws Remove 2 screws
Remove 2 screws
Tighten 4 screws
Step 5
Step 6
CART BASE
BACK PANEL
7
123
4
910
8
7
9
TANK BRACKETS

6
• Attach CART
BASE to back
legs
• Tighten 4 screws
(Removed from
Step 6)
• Attach LEFT SIDE
PANEL and
CART BRACE
• Tighten 4 screws
CART BASE
Step 7
Step 8
LEFT
SIDE
PANEL
77
8
9
10
5
5
6
Screws removed
from Step 6
CART BRACE

7
• Lock CASTERS
• Attach CASTERS
to legs
• Set cart upright on
CASTERS
unlocked
locked
Step 9
Step 10
CASTERS
9
3
6
7

8
• Loosen 2 bottom
screws
• Install BAR
• Tighten 2 screws
Step 11a
Step 11b
Tighten screw Tighten screw
BAR
6
6
CART BASE
TOP VIEW
Loosen bottom screws
CART BASE

9
• Set GRILL BODY
on cart
• Remove 3 screws
• Align GRILL
BODY to cart
• Rotate CART
BRACKETS
upwards and
tighten 4 screws
Step 12
Step 13
Remove screw
Remove
screw
GRILL BODY
Tighten screws
GRILL BODY
GRILL BODY
Remove screw
CART BRACKETS
Align Panels