Cuisinart GAS9556AS Quick start guide

3-in-1 Stainless 5 Burner Gas Grill
Model GAS9556AS / GAS9556ASO
ASSEMBLY INSTRUCTIONS

1
ASSEMBLY INSTRUCTIONS:
READ ALL SAFETY WARNINGS & ASSEMBLY INSTRUCTIONS CAREFULLY
BEFORE ASSEMBLING OR OPERATING YOUR GRILL.
WE RECOMMEND TWO PEOPLE WORK TOGETHER WHEN ASSEMBLING THIS UNIT.
The following tools are required to assemble this Cuisinart 5 Burner Gas Grill:
• Phillips Screwdriver
• Pliers or Wrench
PARTS LIST:
1 Right Front Leg
1 Front Panel
1 Left Front Leg
1 Right Side Panel
1 Left Side Panel
1 Cart Brace
1 Cart Base
1 Left Rear Leg
1 Back Panel
1 Right Rear Leg
1 Side Burner Grate
5 Heat Tents
1 Side Burner Knob
1 Right Side Control Panel
1
2
3
4
5
6
7
8
11
9
10
12
1 Grease Cup
1 Warming Rack
1 Heat Shield
1 Right Side Table
1 Left Side Table
1 Grill Body
1 Left Side Control Panel
4 Casters
3 Cooking Grates
1 Grease Tray
1 Griddle
1 Smoke Tube
2 Griddle Hooks
1 Bar
15
16
17
18
19
20
21
22
25
23
24
26
13
14
27
28
28
Note: Most hardware is pre-attached to the grill. You may need to loosen some screws
partially while others may need to be removed in order to assemble parts. The screws that
you remove will be re-used so don’t misplace this hardware.
Extra screws are included in a small bag with the owners manual.

2
20
19 18
21 14
16
23
12
11
8
5
96
3
2
1
724
10
22
25
26
27
28
13
17
15
4

3
Step 1b
• Loosen 6 screws
3-4 turns FRONT
LEGS and
• Do not remove
screws
• Attach FRONT
PANEL using
keyholes
• Tighten 6 screws
FRONT PANEL
123
2
NOTE: Before tightening keyhole
screws, make sure panels are aligned.
• Loosen screw on
each BRACKETS
• Rotate all
BRACKETS
upward and lock
into slot.
• Tighten screws
Step 1a
1
3
108
1 3
BRACKETS

4
• Loosen 2 screws
• Attach LEFT
SIDE PANEL
• Tighten 2 screws
on LEFT SIDE
PANEL
Step 3
LEFT
SIDE
PANEL
5
• Loosen 3 screws
• Attach RIGHT
SIDE PANEL
• Tighten 3 screws
on RIGHT SIDE
PANEL
Step 2
RIGHT SIDE
PANEL
4
4
4
5
5

5
• Attach CART
BASE
• Make sure TANK
• BRACKETS are
on this end. (See
drawing below)
• Tighten 4 screws
(Removed from
Step 4)
Step 5
Tighten 4 screws
CART BASE
7
7
• Remove 6 screws
• Attach CART
BRACE
• Tighten two
screws on CART
BRACE
Step 4
Remove 2 screws Remove 2 screws
CART BRACE
6
6
6
TANK BRACKETS

6
• Loosen 6 screws
on REAR LEGS
and
• Attach BACK
PANEL
• Tighten 4 screws
• Remove 6 screws
• Attach CART
BASE to back
legs
• Tighten 4 screws
(Removed from
Step 6) Attach
CART BASE to
the back legs
Remove 2 screws Remove 2 screws
Remove 2 screws
CART BASE
Step 6
Step 7
BACK PANEL
910
8
9
7
7
810
7

7
• Lock CASTERS
• Attach CASTERS
to legs
Step 9
CASTERS
locked
unlocked
• Attach LEFT SIDE
PANEL and
CART BRACE
• Tighten 4 screws
Step 8 LEFT
SIDE
PANEL
5
5
6
Screws removed
from Step 6
CART BRACE
22
22
22
6

8
LEFT
SIDE
PANEL
5
GRIDDLE
HOOKS
• Attach GRIDDLE
HOOKS to LEFT
SIDE PANEL
• NOTE: Washer and
nut used to attach
GRIDDLE
HOOKS go on
the back side of
LEFT SIDE
PANEL
Step 10
• Loosen 2 bottom
screws
Step 11a
CART BASE
TOP VIEW
Loosen bottom screws
5
27
27
27
5
7

99
LEFT SIDE
• Loosen screw
• Remove 2 screws
RIGHT SIDE
• Loosen screw
• Remove 2 screws
Step 12
Remove screws
Loosen screw
Remove screws Loosen screw
LEFT SIDE
RIGHT SIDE
• Install BAR
• Tighten 2 screws
Step 11b
Tighten screw Tighten screw
BAR
6
CART BASE
LEFT SIDE
• Loosen screw
• Remove 2 screws
RIGHT SIDE
• Loosen screw
• Remove 2 screws
Step 12
Remove screws
Loosen screw
Remove screws Loosen screw
Step 11b
Tighten screw Tighten screw
BAR
6
CART BASE
28
28