CULITEK MXR-10 User manual

Planetary Mixers
A Professional Line of Commercial Equipment
Instruction Manual
Planetary Mixers
MODELS: MXR-10, MXR-20, MXR-30, MXR-60
This manual contains important information regarding your Culitek unit. Please read this manual
thoroughly prior to equipment set-up, operation and maintenance. Failure to comply with regular
maintenance guidelines outlined in this manual may void the warranty.

Dough Hook Wire Whip Mixing Bowl
WARNINGS
• Do not immerse unit, cord or plug in liquid at any time
• Unplug cord from outlet when not in use and before cleaning
• Plug only into a 3-hole grounded electrical outlet of appropriate voltage
• Do not operate unattended
• Do not use this unit for anything other than intended use
• Do not use outdoors
•Always use on a rm, dry and level surface at least 12” from walls or any other obstruction
• Do not use if unit has a damaged cord or plug, in the event the appliance malfunctions, or has been damaged in any
manner
• Keep children and animals away from unit
• Any incorrect installation, alterations, adjustments and/or improper maintenance can lead to property loss and
injury. All repairs should be done by authorized professionals only
• Ensure that the designated power supply is adequate for continual usage
• Do not hose down mixer
• Do not operate with wet hands
• Unplug from the electrical supply prior to any maintenance or repairs
TO INSTALL:
1. Remove unit from box and make sure all plastic, tape and packing materials are removed.
2. Place the unit on a at, secure surface with at least 12” of open space around all sides.
3. Check to make sure the outlet of the correct voltage for this item (120V) is near. Do not use an extension cord, this
item must be plugged directly into an outlet.
STANDARD ACCESSORIES - This mixer comes with one of each of the following accessories:
When mixing always use the correct agitator for the job. To install agitator raise into the mixing axle and rotate
clockwise on the shaft until it locks into place. To remove an agitator, raise it on the shaft until it clears the lock and
rotate counterclockwise and lower. All of the accessories are tted to the mixing bowl for precise use.
Flat Beater - Used for mixing dry ingredients and can work on all speeds. Do not run for more than 15 minutes.
Dough Hook - Used for mixing dough and can work in low and medium speeds only. Do not use on high speed. Do
not run for more than 20 minutes.
Wire Whip - Used for mixing liquids and soft ingredients and can work in all speeds. Do not run for more than
15 minutes.
NOTE: Always stop the machine rst before changing speeds in order to avoid damage to the unit’s gears. Always
ensure that the bowl is fully lifted and the wire guard is closed when in use.
• Slow speed is the middle setting (Dough hook setting with the knob facing forward)
• Medium speed is the bottom setting (Flat beater setting with the knob facing down)
• High speed is the top setting (Wire Whip setting with the knob facing up)
Flat Beater
*Dough Hook may differ in
appearance from what is shown
*

Helpful measurements for calculating the correct size mixer for your application
8.3 lbs = 1 gallon of water - 2.08 lbs = 1 Quart
When mixing dough (Pizza, bread or bagels), remember to check your “AR” absorption ratio. Absorption ratio is water
weight divided by our weight. The above capacities are based on 12% our moisture at 70°F water temperature. If a
high gluten our is used, reduce above dough batch size by 10%.
Example: if a recipe calls for 5 lbs of water and 10 lbs of our then 5 divided by 10 = 0.50 x 100 = 50% AR.
NOTES:
• 2nd speed should never be used on mixtures with less than 50% AR
• Do not use attachments on the #12 hub while mixing
TO USE:
1. Plug the unit into an outlet of the appropriate voltage.
2. With unit turned off insert the mixing bowl into the holder in the down position and align on the pins. Once bowl is
securely aligned on pins, lock into place with the side clips.
3. Insert the desired agitator onto the mixing axle and turn to lock into place as directed on page 2.
4. Once the bowl and agitator are locked into place, add ingredients to the bowl and raise the bowl by pulling the bowl
lift handle towards you until it hits its full raised position.
5. Adjust your speed setting for the correct application by turning the knob to the correct position as described on
page 2.
6. Set the timer for the desired mixing time. The timer has two settings; turn the dial to the left for manual run or you
can turn the dial to the right to a desired set time for mixing. Once the timer goes off the machine will shut down.
The timer must be set to one of these settings or the machine will not operate.
7. With bowl in the fully raised position, the agitator locked into place and the correct speed setting selected, close the
wire guard over the bowl, set the timer and press the green power button to start mixing. The wire guard must be
closed fully for machine to operate.
8. Once mixing is completed, press the red stop button to stop the agitator.
9. Open the wire guard and lower the bowl to its lowest setting. If more mixing is needed repeat step 7.
NOTE: Always stop the machine before changing speeds.
Meat Grinder Attachment:
• The Meat Grinder should only be used for purposes intended
• Please remove bones, skins and any other foreign materials before grinding
• Meats and other food should be defrosted and not used when frozen
•For best results, cut the meat into smaller size pieces to t easily through the feed tube
• If not in use, please remove the meat grinder attachment from the unit
• Do not run the grinder for longer periods of time then necessary
FOR MODELS MXR-20, MXR-30, MXR-60

CLEANING - NOTE: To maintain cleanliness and increase service life, this item should be cleaned daily. Do not immerse the
unit in water or any other liquid, if liquid enters the electrical compartment it may cause a short circuit or electrical shock.
1. Before cleaning or attempting to move this item always turn off and unplug.
2. Wipe the entire unit with a clean soft cloth until it is completely dry.
3. To avoid damage to the unit, do not use abrasive cleaners or scouring pads.
4. If soap or chemical cleaners are used, be sure they are completely rinsed away with clean water immediately after
cleaning. Chemical residue could damage or corrode the surfaces of the unit.
5. After using of the machine, please remove the at beater, dough hook, wire whip and meat grinder from the machine
and wash these parts thoroughly in hot, soapy water to prevent the growth of bacteria.
6. When clean and maintain the inside of the protective cover and swivel mount, please loosen the screw around the
protective cover and take off the protective cover. If there is no sign of oil leak, no need to take off the swivel mount.
Clean the swivel mount with a wet cloth, the protective cover can be cleaned by detergent and washed under the wa-
ter supply tap. After washing by clean water, use dry cloth to wipe out the water and make it dry.
Problem Possible Causes Solution
The axles don’t work when
operating the machine
Electrical connection is not
good Check the plug in the outlet
Leaking oil oil gaskets are worn out or
damadged Replace the oil gasket(s)
Difcult to raise or lower the
bowl
Either the slideway is
corroded, or the lead screw,
bevel gear or hand wheel
shaft is dried out
Clean and oil the dried out
parts
Motor is overheating and
speed has decreased
The voltage is not enough,
incorrect speed is set or there
is too much food in the bowl
Check the voltage or adjust
the speed to a better setting.
If the bowl is overloaded,
remove some of the food to
lighten the load
Item is making too much
noise and overheating Poor lubrication Add or replace oil
Agitator touches bowl Either the bowl or agitator
is deformed
Repair or replace deformed
part
Mixing bowl is out of position Moving direction is not
correct Adjust position
TROUBLESHOOTING
To avoid serious injury or damage, never attempt to repair or replace a damaged power cord yourself. Contact a professional repair
service.
TO REMOVE GUIDE RAIL DUST GUARD PLATE FOR REGULAR CLEANING:
1. Rotate wheel to release bowl to the lowest position
2. Loosen screws on both sides of the guide rail dust guard plate
3. Remove the guide rail dust guard plate to clean, and ensure to clean inside the hole.
(Note: If screws are loosened manually, it is not necessary to remove the handwheel. If a power tool is used, the handwheel
must be removed first)

Product Agitator Speed
Max Bowl
Capacity (10 qt)
Bread and roll dough - 60% AR Dough hook 1st only 12 lbs
Heavy bread dough - 55% AR Dough hook 1st only * NR
Pasta Basic Egg Noodle (max, mix time 5 min) Dough hook 1st only * NR
Pizza dough, thin - 40% AR (max, mix time 5 min) Dough hook 1st only * NR
Pizza dough, medium - 50% AR Dough hook 1st only * NR
Pizza dough, thick - 60% AR Dough hook 1st only * NR
Raised donut dough - 65% AR Dough hook 1st and 2nd *NR
Whole wheat dough - 70% AR Dough hook 1st only *NR
Mashed potatoes Flat beater 2nd 9 lbs
Mayonnaise (Quarts of Oil) Flat beater 2nd 4 qts
Wafe or pancake batter Flat beater 2nd 4 qts
Egg whites Wire whip 3rd 1 pt
Meringue (Qty. of water) Wire whip 3rd 3/4 pt
Whipped cream Wire whip 3rd 2 qts
Cake, Angel Food (8-10 oz. cake) Wire whip 2nd 6 lbs
Cake, Box or Slab Flat beater 2nd 11 lbs
Cake, Cup Flat beater 2nd 11 lbs
Cake, Layer Flat beater 2nd 11 lbs
Cake, Pound Flat beater 2nd 11 lbs
Cake Short (Sponge) Wire whip 3rd 7 lbs
Cake Sponge Wire whip 3rd 5.5 lbs
Cookies, Sugar Flat beater 2nd 9 lbs
Pie dough Flat beater 2nd 10 lbs
Eggs & Sugar for Sponge Cake Flat beater 2nd 4 lbs
Icing, Fondant Flat beater 2nd 6 lbs
Icing, Marshmallow Wire whip 2nd 1 lbs
Shorting & Sugar, Creamed Flat beater 2nd 8.5 lbs
MIXER CAPACITY CHART
*NR = Not Recommended
MODEL: 10 QT.
MXR-10

Wiring Diagram for the Planetary Mixer
MODEL: 10 QT.
MXR-10

Parts Diagram and Replacement Parts for the Planetary Mixer
MODEL: 10 QT.
MXR-10

Replacement Parts for the Planetary Mixer
Drawing
Number
Part Description Drawing
Number
Part Description
1
Motor Threaded Rod 51 Bearing
2Oil Seal 52 Bearing
3Bearing 53 Flat Key
4Motor Rotor 54 Planetary Shaft
5Motor Stator 55 Taper Pin
6Centrifugal Switch Rotor Plate 56 Shifting Fork Guide Rod
7Centrifugal Switch Static Plate 57 Shifting Fork
8Bearing 58 Shifting Fork Top Latch
9Motor End Shield 59 Shifting Fork Spring
10 Fan 60 Shifting Fork Nut
11 Bearing 61 Variable Speed Handle
12 Input Axis 62 Position Limit Steel Ball
13 Flat Key 63 Position Limit Spring
14 Flat Key 64 Variable Speed Handle
15 Flat Key 65 Variable Speed Base
16 Upper Gear 66 Button-headed Screw
17 Input Axis Upper Sleeve 67 Shaft Circlip
18 Worm Wheel 68 Box
19 Input Axis Lower Sleeve 69 Annular Gear
20 Lower Gear 70 Inner Hexagon Socket Head Cap Screw
21 Shaft Circlip 71 Protective Cover Mount
22 Bearing 72 Moveable Protective Cover
23 Bearing 73 Hook
24 Ratchet Cover 74 Beater
25 Outer Ring 75 Whip
26 Internal Star Wheel 76 Bowl
27 Roller 77 Bowl Mount
28 Roller Spring 78 Bowl Tight Pressing Handle
29 Clutch Upper Gear 79 Handle Pin
30 Output Shaft Gear Sleeve 80 Bowl Alignment Pin
31 Output Shaft Clutch 81 Spring Washer
32 Output Shaft 82 Nut
33 Flat Key 83 Support Pillar
34 Flat Key 84 Inner Hexagon Socket Head Cap Screw
35 Flat Key 85 Outer Hexagon Screw
36 Output Shaft Gear Sleeve 86 Pressplate
37 Clutch Lower Gear 87 Base
38 Upper Sleeve For Bearging 88 Locking Sleeve
39 Bearing 89 Inner Hexagon Socket Head Cap Screw
40 O Shape Ring 90 Handle
41 Bearing Mount 91 Support Bar
42 Oil Seal 92 Pin With Hole Ends
43 Bearing Lower Sleeve 93 Splitpin
44 Swivel Mount 94 Lifting Up and Down Rod
45 Flat Washer 95 Nut
46 Spring Washer 96 Enlarged Flat Washer
47 Nut 97 Compression Spring
48 Outer Hexagon Screw 98 Rear Cover
49 Enlarged Flat Washer 99 Start Button
50 Planetary Gear 100 Stop Button
Drawing
Number
Part Description
101 Switch Panel
102 Micro Switch
103 Position Switch
104 Position Switch Box
105 Electric Box
106 Capacitor
107 Contactor
108 Overload Protector
109 Power Switch
110 Electric Box Cover
MODEL: 10 QT.
MXR-10

September 2018
Product Agitator Speed
Max Bowl
Capacity (20 qt)
Bread and roll dough - 60% AR Dough hook 1st only 25 lbs
Heavy bread dough - 55% AR Dough hook 1st only 15 lbs
Pasta Basic Egg Noodle (max, mix time 5 min) Dough hook 1st only 5 lbs
Pizza dough, thin - 40% AR (max, mix time 5 min) Dough hook 1st only 9 lbs
Pizza dough, medium - 50% AR Dough hook 1st only 10 lbs
Pizza dough, thick - 60% AR Dough hook 1st only 20 lbs
Raised donut dough - 65% AR Dough hook 1st and 2nd 9 lbs
Whole wheat dough - 70% AR Dough hook 1st only 20 lbs
Mashed potatoes Flat beater 2nd 15 lbs
Mayonnaise (Quarts of Oil) Flat beater 2nd 8 qt
Wafe or pancake batter Flat beater 2nd 8 qt
Egg whites Wire whip 3rd 1 qt
Meringue (Qty. of water) Wire whip 3rd 1.5 pts
Whipped cream Wire whip 3rd 4 qt
Cake, Angel Food (8-10 oz. cake) Wire whip 2nd 15 lbs
Cake, Box or Slab Flat beater 2nd 20 lbs
Cake, Cup Flat beater 2nd 20 lbs
Cake, Layer Flat beater 2nd 20 lbs
Cake, Pound Flat beater 2nd 21 lbs
Cake Short (Sponge) Wire whip 3rd 15 lbs
Cake Sponge Wire whip 3rd 12 lbs
Pie dough Flat beater 2nd 18 lbs
Eggs & Sugar for Sponge Cake Flat beater 2nd 8 lbs
Icing, Fondant Flat beater 2nd 12 lbs
Icing, Marshmallow Wire whip 2nd 2 lbs
Shorting & Sugar, Creamed Flat beater 2nd 9.5 lbs
MIXER CAPACITY CHART
MODEL : 20 QT
MXR-20

September 2018
Wiring Diagram for the Planetary Mixer
MODEL : 20 QT
MXR-20

September 2018
Parts Diagram and Replacement Parts for the Planetary Mixer
MODEL : 20 QT
MXR-20

September 2018
Replacement Parts for the Planetary Mixer
Drawing
Number
Part Description Drawing
Number
Part Description
1Nut 51 Button-headed Screw
2Spring Washer 52 Motor Rotor
3Flat Washer 53 Flat Key
4Skeleton Oil Seal 54 Bearing
5Shaft Circlip 55 Skeleton Oil Seal
6Bearing 56
Motor Threaded Rod
7Upper Sleeve For Lower Bearging 57 Motor Stator
8Clutch Lower Gear 58 Input Axis
9Output Shaft Gear Sleeve 59 Worm Wheel
10 Flat Key 60 Shifting Fork Guide Rod
11 Output Shaft 61 Shifting Fork Nut
12 Flat Key 62 Shifting Fork Spring
13 Output Shaft Clutch 63 Shifting Fork Top Latch
14 Clutch Upper Gear 64 Shifting Fork
15 Driving Bevel Gear 65 Eccentric Bushing
16 Outer Ring Gear 66 Taper Pin
17 Roller Spring 67 Variable Speed Mandrel
18 Roller 68 Variable Speed Handle
19 Internal Star Wheel 69 Position Limit Steel Ball
20 Ratchet Upper Cover 70 Position Limit Spring
21 Bearing 71 Variable Speed Base
22 Flat Washer 72 Gear Panel
23 Spring Washer 73 Button-headed Screw
24 Nut 74 Planetary Gear
25 Nut 75 Bearing
26 Spring Washer 76 Bearing
27 Flat Washer 77 Skeleton Oil Seal
28 Bearing 78 Flat Key
29 Intermediate Bridge Shaft 79 Taper Pin
30 Flat Key 80 Planeatry Shaft
31 Intermediate Shaft Large Gear 81 Centrifugal Switch Rotor Plate
32 Intermediate Shaft Long Sleeve 82 Centrifugal Switch Static Plate
33 Intermediate Shaft Small Gear 83 Motor End Shield
34 Shaft Circlip 84 Fan
35 Bearing 85 Box Rear Cover
36 Circular plate 86 Inner Hexagon Screw
37 Movable Protective Cover 87 Hook
38 Inner Hexagon Screw 88 Beater
39 Internal Gear 89 Whip
40 Button-headed Screw 90 Bowl
41 Swivel Mount 91 Bowl Mount
42 Protective Cover Mount 92 Bowl Tight Pressing Handle
43 Box 93 Handle Pin
44 Bearing Mount 94 Bowl Alignment Pin
45 Inner Hexagon Screw 95 Spring Washer
46 Single Bearing Cover 96 Nut
47 Duplex Bearing Cover 97 Support Pillar
48 Inner Hexagon Screw 98 Inner Hexagon Socket Head Cap Screw
49 Button-headed Screw 99 Outer Hexagon Screw
50 Upper Cover 100 Pressplate
Replacement Parts for the Planetary Mixer
MODEL : 20 QT
MXR-20

September 2018
Replacement Parts for the Planetary Mixer
Drawing
Number
Part Description
101 Base
102 Locking Sleeve
103 Inner Hexagon Socket Head Cap Screw
104 Reversal Handle
105 Support Bar
106 Pin With Hole Ends
107 Splitpin
108 Lifting Up and Down Rod
109 Nut
110 Enlarged Flat Washer
111 Compression Spring
112 Passive Bevel Gear
113 Bearing
114 Distance Sleeve of Axletree
115 Oil Seal
116 Bevel Gear Base
117 Meat Grinder Casing
118 Casing Bushing
119 Auger
120 Mandrel
121 Cross Knife
122 Pore Plate
123 Hand Wheel
124 Tray
125 Stop Button
126 Start Button
127 Timer
128 Switch Panel
129 Micro Switch
130 Position Switch
131 Position Switch Box
132 Electric Box
133 Capacitor
134 Contactor
135 Overload Protector
136 Power Switch
137 Electric Box Cover
Replacement Parts for the Planetary Mixer
MODEL : 20 QT
MXR-20

September 2018
Product Agitator Speed
Max Bowl
Capacity (30 qt)
Bread and roll dough - 60% AR Dough hook 1st only 45 lbs
Heavy bread dough - 55% AR Dough hook 1st only 30 lbs
Pasta Basic Egg Noodle (max, mix time 5 min) Dough hook 1st only 8 lbs
Pizza dough, thin - 40% AR (max, mix time 5 min) Dough hook 1st only 14 lbs
Pizza dough, medium - 50% AR Dough hook 1st only 20 lbs
Pizza dough, thick - 60% AR Dough hook 1st only 40 lbs
Raised donut dough - 65% AR Dough hook 1st and 2nd 15 lbs
Whole wheat dough - 70% AR Dough hook 1st only 40 lbs
Mashed potatoes Flat beater 2nd 23 lbs
Mayonnaise (Quarts of Oil) Flat beater 2nd 12 qts
Wafe or pancake batter Flat beater 2nd 12 qts
Egg whites Wire whip 3rd 1.5 qt
Meringue (Qty. of water) Wire whip 3rd 1 qt
Whipped cream Wire whip 3rd 6 qts
Cake, Angel Food (8-10 oz. cake) Wire whip 2nd 22 lbs
Cake, Box or Slab Flat beater 2nd 30 lbs
Cake, Cup Flat beater 2nd 30 lbs
Cake, Layer Flat beater 2nd 30 lbs
Cake, Pound Flat beater 2nd 30 lbs
Cake Short (Sponge) Wire whip 3rd 23 lbs
Cake Sponge Wire whip 3rd 18 lbs
Cookies, Sugar Flat beater 2nd 23 lbs
Pie dough Flat beater 2nd 27 lbs
Eggs & Sugar for Sponge Cake Flat beater 2nd 12 lbs
Icing, Fondant Flat beater 2nd 18 lbs
Icing, Marshmallow Wire whip 2nd 3 lbs
Shorting & Sugar, Creamed Flat beater 2nd 24 lbs
MIXER CAPACITY CHART
MODEL : 30 QT
MXR-30

September 2018
Wiring Diagram for the Planetary Mixer
MODEL : 30 QT
MXR-30

September 2018
Parts Diagram and Replacement Parts for the Planetary Mixer
MODEL : 30 QT
MXR-30

September 2018
Replacement Parts for the Planetary Mixer
Drawing
Number
Part Description Drawing
Number
Part Description
1Nut 51 Centrifugal Switch Rotor Plate
2Spring Washer 52 Centrifugal Switch Static Plate
3Flat Washer 53 Motor End Shield
4Skeleton Oil Seal 54 Fan
5Lower Sleeve For Bearing 55 Box Rear Cover
6Bearing 56 Inner Hexagon Socket Head Cap Screw
7Upper Sleeve For Bearing 57 Button-headed Screw
8Clutch Lower Gear 58 Upper Cover
9Flat Key 59 Button-headed Screw
10 Output Shaft 60 Bearing Cover
11 Flat Key 61 Bearing Block
12 Output Shaft Clutch 62 Box
13 Output Shaft Gear Sleeve 63 Shifting Fork Guide Rod
14 Clutch Upper Gear 64 Shifting Fork Nut
15 Driving Bevel Gear 65 Shifting Fork Spring
16 Outer Ring Gear 66 Shifting Fork Top Latch
17 Roller Spring 67 Shifting Fork
18 Roller 68 Eccentric Bushing
19 Internal Star Wheel 69 Taper Pin
20 Ratchet Upper Cover 70 Position Limit Steel Ball
21 Bearing 71 Position Limit Spring
22 Bearing 72 Variable Speed Base
23 Intermediate Bridge Shaft 73 Button-headed Screw
24 Flat Key 74 Variable Speed Mandrel
25 Intermediate Bridge Shaft Upper Gear 75 Variable Speed Handle
26 Intermediate Bridge Shaft Sleeve 76 Whip
27 Intermediate Bridge Shaft Middle Gear 77 Hook
28 Intermediate Bridge Shaft Lower Gear 78 Beater
29 Inner Hexagon Socket Head Cap Screw 79 Bowl
30 Annular Gear 80 Bowl Mount
31 Swivel Mount 81 Bowl Tight Pressing Handle
32 Protective Cover Mount 82 Handle Core Shaft
33 Protective Cover 83 Bowl Alignment Pin
34 Nut 84 Support Pillar
35 Flat Washer 85 Base
36 Planetary Gear 86 Pressplate
37 Bearing 87 Hexagon Headed Bolt
38 Bearing 88 Spring Washer
39 Flat Key 89 Inner Hexagon Socket Head Cap Screw
40 Taper Pin 90 Elevating Handwheel
41 Planetary Shaft 91 Inner Hexangular Cone Set Screw
42 Bearing 92 Inner Hexagon Socket Head Cap Screw
43 Input Shaft 93 Spring Washer
44 Flat Key 94 Handwheel Shaft Fixing Seat
45 Worm Wheel 95 Handwheel Shaft
46
Motor Threaded Rod 96 Driving Bevel Gear
47 Skeleton Oil Seal 97 Lifting Screw
48 Bearing 98 Antifriction Bearing
49 Flat Key 99 Shaft Circlip
50 Motor Rotor 100 Lifting Nut
MODEL : 30 QT
MXR-30

September 2018
Replacement Parts for the Planetary Mixer
Drawing
Number
Part Description
101 Passive Bevel Gear
102 Bearing
103 Distance Sleeve of Axletree
104 Oil Seal
105 Bevel Gear Base
106 Meat Grinder Casing
107 Casing Bushing
108 Auger
109 Mandrel
110 Cross Knife
111 Pore Plate
112 Hand Wheel
113 Tray
114 Stop Button
115 Start Button
116 Timer
117 Switch Panel
118 Micro Switch
119 Position Switch Box
120 Position Switch
121 Electric Box
122 Capacitor
123 Contactor
124 Overload Protector
125 Power Switch
126 Electric Box Cover
Timer
Stop Button
MODEL : 30 QT
MXR-30

March 2019
MIXER CAPACITY CHART
Product Agitator Speed
Max Bowl
Capacity (60 qt)
Bread and roll dough - 60% AR *•◊
Dough hook
1st only
80 lbs
Heavy bread dough - 55% AR *•◊
Dough hook
1st only
70 lbs
Pasta Basic Egg Noodle
Dough hook
40 lbs
Pizza dough, thin - 40% AR *X•◊□
Dough hook
1st only
40 lbs
Pizza dough, medium - 50% AR *•◊□
Dough hook
1st only
70 lbs (1st)/35lbs (2nd)
Pizza dough, thick - 60% AR *•◊
Dough hook
1st only
70 lbs
Raised donut dough - 65% AR *◊
Dough hook
1st and 2nd
60 lbs
Mashed potatoes
Flat beater
40 lbs
Waffle or Hotcake batter
Flat beater
24 qts
Egg whites
Wire whip
2 qts
Meringue (Qty. of water)
Wire whip
1
3/4
qts
Whipped cream
Wire whip
12 qts
Fondant Icing
Flat Beater
36 lbs
Cake
Flat beater
60 lbs
Pie Dough
Flat beater
50 lbs
*NOTE: The mixer capacity depends on the moisture content of the dough. When mixing doughs (pizza, bread, or bagels)
remember to check your AR%!
%AR (% Absorption Ration) = Water weight divided by flour weight. The capacities listed in the cart above are based on flour
at room temperature and 70˚F water temperature
XMaximum Mixing Time – 7 minutes
•If high gluten flour is used, reduce the batch size by 10%
◊If using chilled flour, water below 70˚F, or ice, reduce batch size by 10%
□2nd speed should never be used on 60% AR or lower with the exception of the BDPM-60. BDPM-60 requires a 50% reduction
in batch size to mix in speed 2 with 50% AR doughs.
Helpful measurements for calculating the correct size mixer for your application
8.3 lbs = 1 gallon of water - 2.08 lbs = 1 Quart
NOTES:
• Do not use attachments on the #12 hub while mixing
MODEL : 60 QT
MXR-60

March 2019
Wiring Diagram for the Planetary Mixer
MODEL : 60 QT
MXR-60