Curtis Alpha G3 Configuration guide

Service & Sales
1-800-421-6150 www.wilburcurtis.com
CURTIS ALP3GT15A826
Alpha G3 Coffee Brewing System with FreshTrac™Technology
OPERATION & CLEANING INSTRUCTIONS

Service & Sales
1-800-421-6150 www.wilburcurtis.com
COMPONENTS
ALPHA G3
Regular FreshTrac™
decanter
Decaf FreshTrac™
decanter
Display with G3
control board
FreshTrac™ transmitter
Warmer
Brew basket
Warmer

Service & Sales
1-800-421-6150 www.wilburcurtis.com
OPERATION INSTRUCTIONS
The FreshTrac™ timer uses
three LED lights (red, yellow
and green), as a visual time
indicator.
When a brew cycle begins, five
quick red flashes indicate that
the timer has started.
The green LED will flash every 15 seconds during
the brew cycle and will continue until 25 minutes
have elapsed.
At 25 minutes, a yellow LED will flash every 3-5
seconds for 5 minutes. This will continue for 5
minutes until 30 minutes has elapsed.
At 30 minutes, the red LED will flash every 3-5
seconds until 60 minutes have elapsed. The red
led indicates that the hold time has elapsed and
any remaining coffee should be discarded.
All flashing LEDs will stop. A new brew cycle will
start restart the FreshTrac™ timer.
1
2
FreshTrac™ timer on the decanter Brewing Instructions
Place empty decanter on the warmer plate under
the brew basket.
Place a new filter in the brew basket.
Pour pre-determined amount of ground coffee into
the filter.
Slide brew basket into the brew rails.
Press the brew button.
1
2
Brewer should be on (conrm at rear toggle switch, then
press on/off button). Ready-to-Brew should be displayed.
FreshTrac™
Transmitter
3
4
5
3
4
5
6
ACCESSORIES
70517430303
McCafe Decanter - Regular
with FreshTrac™Transmitter
White ink/black handle
WRIN 10560-000
70517430103
McCafe Decanter - Decaf
with FreshTrac™Transmitter
White ink/orange handle
WRIN 10562-000
70217430303
McCafe Decanter - Regular
without FreshTrac™Transmitter
White ink/black handle
WRIN 10561-000
70217430103
McCafe Decanter - Decaf
without FreshTrac™Transmitter
White ink/orange handle
WRIN 10563-000
WC -10 0 11
FreshTrac™Transmitter
On/RFID Collar Assembly

Service & Sales
1-800-421-6150 www.wilburcurtis.com
CLEANING INSTRUCTIONS
Regular cleaning and preventative maintenance is essential in keeping your coffee brewer and decanters looking
and preforming at optimal efficiency.
i
!CAUTION - Do not use cleansers, liquid bleach, powders or any other substance containing chlorine. These products
promote corrosion and will pit the stainless steel. THE USE OF THESE PRODUCTS WILL VOID THE WARRANTY.
Turn brewer OFF at the power
toggle switch behind brewer.
Allow brewer to cool.
Wipe exterior surfaces with a
cloth moistened with warm water
to remove spills and debris.
Slide the brew basket out and
dispose of used coffee grounds.
Rinse brew basket with warm
water. Dry with paper towel.
1
2
3
4
5
6
Bucket, warm water Bucket, clean towels Bucket, soiled towels Cloth towel Paper towelsStainless steel polish
Tools and supplies
Clean the spray head area with a
moist clean cloth.
With a moist cloth, apply stainless
steel polish on the exterior
surfaces of the brewer.
Return brew basket to brewer.
Turn brewer ON at the power
toggle switch behind brewer.
Cleaning the coffee brewer
Cleaning the glass decanter
Bucket with Esteem Ware Washing Detergent Sponge brush Paper towels
Tools and supplies
Prepare a mild solution of
detergent and warm water.
Immerse the decanter in detergent
solution and clean with a sponge
brush.
1
2
Thoroughly rinse the glass
decanter with clean warm water.
Dry the decanter.
1
2

Service & Sales
1-800-421-6150 www.wilburcurtis.com
www.wilburcurtis.com
FEB/2014 M18_OG_MD_FreshTrac_revA
QUICK VOLUME/TEMPERATURE ADJUSTMENT
The UCM must be on. To adjust the ALP1GT models, press and hold the center, Select button . The screen will read
pressing < or > will adjust the brew volume up or down ± 20 oz., in 1 ounce increments.
On any multi-station Alpha (ALP2/3/4/5/6GT: Press the center Select button twice, with the second press, hold
down the button for around five (5) seconds. The screen will display pressing < or > will adjust the brew
volume up or down, ± 20 oz., in 1 ounce increments.
Turn on brewer at the control panel ON/OFF button. Press and hold button (see illustration below) for 5 seconds.
Water temperature will be displayed. The temperature will not display while the unit is in the process of reheating.
NOTE: Alpha 3GT ONLY; when checking tank temperature, first make sure REAR warmer is ON (red LED on) and then
press for 5 seconds to display tank temperature.
Quick Volume Adjustment
Tank Temperature Check