Custom Audio Electronics PATH 15 Supplement
SHORT GUIDE
PATH 15
Thank you for choosing
a Custom®product
IDENTIFICATION OF THE MODELS
US market System memory support up to 8GB DDR3 L
EU market System memory support up to 4GB DDR3 L
12 3 4
BOX CONTENTS
Remove the device from its carton being careful not to damage the packing material so that it may be re-used if the device is to be transported in the future. Make sure that all the
components illustrated below are present and that there are no signs of damage. If there are, contact customer service.
1. Device
2. Documentation (short guide, warranty card)
3. Standard AC power supply cable or US market AC power
4. AC adapter
5
3
4
8
6
5
7
1
2
DEVICE DESCRIPTION
1. Touch screen
2. Status LED
3. Client display (only US market)
4. Set-up for stripe card reader (MSR)
5. Connectors panel
6. Stand
7. Stand cover
8. Set-up for HDD
65432
17
CONNECTORS PANEL
1. Power supply port
2. USB 2.0 port (x 4)
3. VGA port (future uses)
4. COM port (x 3)
5. Ethernet port
6. Cash drawer port
7. Power ON/OFF key
STATUS LED
STATUS LED DESCRIPTION
GREEN ON DEVICE ON
GREEN OFF DEVICE OFF
7
USB 2.0 VGA COM ETH CASH
DRAWER
POWER
SUPPLY
Power
supply
cable
(included)
VGA cable
(not included)
Standard
USB A cable
(non included)
Ethernet
cable
(not included)
Cash drawer
cable
(not included)
Serial cable
(not included)
CONNECTIONS
IN DC 12V 5A
Power supply cable
(included)
ON/OFF
12
43
TURN ON
1. Remove the cover from the stand lifting it from the bottom side.
2.
3. Reassemble the cover of the bracket.
4. Connect the power adapter (supplied) to the device and the mains outlet. Use the type of electrical power supply indicated on the label. Press the ON/OFF key to switch on the device,
9
TECHNICAL SPECIFICATIONS
GENERAL
CPU / Chipset Intel®Celeron®Processor Bay-Trail J1900, up to 2.42 GHz
System memory
US market Support up to 8 GB DDR3 L
EU market Support up to 4 GB DDR3 L
Storage 1 x 128 GB 2.5" SSD
Mounting VESA Mount 75x75 mm
Interface
Serial port: 3 x RJ50 for RS232 ports via
COM port connectors
USB port: 4 x USB 2.0 Type-A
Ethernet port: 1 x RJ45 10/100/1000 Mbps
Power supply port: 1 x DC12 V, 2.5 mm DC Jack
VGA port: riserved
Cash drawer port: 1 x RJ11
LCD
Dimension 15” TFT LCD
Resolution max. 1024 x 768
Brightness 300 cd/m² (typ.)
Touch screen True-Flat PCAP Touch
DEVICE ELECTRICAL SPECIFICATIONS
Power supply 60 W/12 V DC Jack Adapter
PERIPHERAL (OPTION)
Magnetic strip reader (MSR) 3-Track MSR (USB)
POWER SUPPLY ELECTRICAL SPECIFICATIONS
Power supply voltage from 100 Vac to 240 Vac
Frequence from 50 Hz to 60 Hz
Output 12 V, 5 A
Power 60 W
ENVIRONMENTAL CONDITIONS
Operating temperature from 0°C to +40°C
Relative humidity
(RH)
from 0% a 90% (without condensation)
Storage temperature from -20 °C to +60 °C
Storage relative humidity (RH)
from 0% to 90% (without condensation)
207.5
312.7
361.6
DEVICE DIMENSIONS
Width 361.6 mm
Length 207.5 mm
Height 312.7 mm
Weight 3940 g
11
12
H
2
O
5 min.
CLEANING
1. Disconnect the power supply cable and wait a few minutes to allow the screen to get to room temperature.
2. To clean the device use compressed air or a soft cloth. Gently wipe the screen with a soft cloth slightly moistened with water.
TECHNICAL SERVICE
In case of failure, contact the technical service accessing the website www.custom4u.it
the product at hand.
The product code, the serial number and the hardware release number can be found on the product label.
13
The format used for this manual improves use of natural resources reducing the quantity of necessary paper to print this copy.
CUSTOM S.p.A.
Via Berettine 2/B
43010 Fontevivo (PARMA) - Italy
Tel. : +39 0521-680111
Fax : +39 0521-610701
http: www.custom.biz
Customer Service Department:
www.custom4u.it
© 2021 CUSTOM S.p.A. – Italy. All rights reserved. Total or partial repro-
duction of this manual in whatever form, whether by printed or electronic
means, is forbidden. While guaranteeing that the information contained
in it has been carefully checked, CUSTOM S.p.A. and other entities
utilized in the realization of this manual bear no responsibility for how
the manual is used.
Information regarding any errors found in it or suggestions on how it could
be improved are appreciated. Since products are subject to continuous
check and improvement, CUSTOM S.p.A. reserves the right to make
The pre-installed multimedia contents are protected from Copyright
CUSTOM S.p.A. Other company and product names mentioned herein
may be trademarks of their respective companies. Mention of third-party
products is for informational purposes only and constitutes neither an
endorsement nor a recommendation. CUSTOM S.p.A. assumes no
responsibility with regard to the performance or use of these products.
THE IMAGES USED IN THIS MANUAL ARE USED AS AN
ILLUSTRATIVE EXAMPLES. THEY COULDN’T REPRO-
DUCE THE DESCRIBED MODEL FAITHFULLY.
UNLESS OTHERWISE SPECIFIED, THE INFORMATION
GIVEN IN THIS MANUAL ARE REFERRED TO ALL MOD-
ELS IN PRODUCTION AT THE ISSUE DATE OF THIS
DOCUMENT.
GENERAL INSTRUCTIONS
CUSTOM S.p.A. declines all responsibility for accidents or damage to
persons or property occurring as a result of tampering, structural or func-
in keeping with the equipment’s protection degree or with the required
temperature and humidity conditions, failure to carry out maintenance
and periodical inspections and poor repair work.
THE CE MARK AFFIXED TO THE PRODUCT CERTIFY
THAT THE PRODUCT SATISFIES THE BASIC SAFETY
REQUIREMENTS.
The device is in conformity with the essential Electromagnetic Compat-
ibility and Electric Safety requirements laid down in Directives 2014/30/
EU and 2014/35/EU inasmuch as it was designed in conformity with the
provisions laid down in the following Standards:
• EN 55032 (Electromagnetic compatibility of multimedia equipment -
Emission Requirements)
• EN EN55024/EN55035 (Electromagnetic compatibility of multimedia
equipment - Immunity requirements)
• EN IEC/EN62368-1 (Audio/video, information and communication
technology equipment)
Warning:
This is a class A product. In a domestic environment this product may
cause radio interference in which case the user may be required to take
adequate measures.
The device is in conformity with the essential requirements laid down in
Directives 2014/53/EU about devices equipped with intentional radiators
downloaded from the site www.custom4u.it.
GUIDELINES FOR
THE DISPOSAL OF
THE PRODUCT
The crossed-out rubbish bin logo means that used electrical and electronic
products shall NOT be mixed with unsorted municipal waste. For more
detailed information about recycling of this product, refer to the instruc-
tions of your country for the disposal of these products.
• Do not dispose of this equipment as miscellaneous solid municipal
waste, but arrange to have it collected separately.
• The re-use or correct recycling of the electronic and electrical equip-
ment (EEE) is important in order to protect the environment and the
wellbeing of humans.
• In accordance with European Directive WEEE 2012/19/EU, special
collection points are available to which to deliver waste electrical and
electronic equipment and the equipment can also be handed over to a
distributor at the moment of purchasing a new equivalent type.
• The public administration and producers of electrical and electronic
equipment are involved in facilitating the processes of the re-use and
recovery of waste electrical and electronic equipment through the or-
ganisation of collection activities and the use of appropriate planning
arrangements.
• Unauthorised disposal of waste electrical and electronic equipment is
punishable by law with the appropriate penalties.
GENERAL SAFETY INFORMATION
Your attention is drawn to the following actions that could compromise
the characteristics of the product:
• Read and retain the instructions which follow.
• Follow all indications and instructions given on the device.
• Make sure that the surface on which the device rests is stable. If it is
not, the device could fall, seriously damaging it.
• Make sure that the device rests on a hard (non-padded) surface and
•
• When positioning the device, make sure cables do not get damaged.
• The mains power supply must comply with the rules in force in the
Country where you intend to install the equipment.
• Make sure that there is an easily-accessible outlet with a capacity of no
less than 10A closely to where the device is to be installed.
• Make sure the power cable provided with the appliance, or that you
intend to use is suitable with the wall socket available in the system.
• Make sure the electrical system that supplies power to the device is
• Before any type of work is done on the machine, disconnect the power
supply.
• Use the type of electrical power supply indicated on the device label.
•
power module having an SELV, non-energy hazardous output. (IEC/
EN62368-1 second edition).
• The energy to the equipment must be provided by power supply ap-
proved by CUSTOM S.p.A.
• Take care the operating temperature range of equipment and its ancil-
lary components.
• Do not block the ventilation openings.
• Do not insert objects inside the device as this could cause short-circ
uiting or damage components that could jeopardize printer functioning.
• Do not carry out repairs on the device yourself, except for the normal
maintenance operations given in the user manual.
• The equipment must be accessible on these components only to
trained, authorized personnel.
• Periodically perform scheduled maintenance on the device to avoid dirt
build-up that could compromise the correct, safe operation of the unit.
FCC STATEMENT (FEDERAL COMMUNICATIONS
COMMISSIONS).
This equipment has been tested and found to comply with the limits for
a Class A digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environ-
ment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Op-
eration of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interfer-
ence at his own expense.
void the FCC & Industry Canada regulations and negate your authority
to operate the product.
www.custom.biz
CUSTOM S.p.A.
World Headquarters
Via Berettine, 2/B - 43010 Fontevivo, Parma ITALY
Tel. +39 0521 680111 - Fax +39 0521 610701
All rights reserved
Code: 0578200M000028 Rev. 1.20
Table of contents
Other Custom Audio Electronics Touch Panel manuals
