CyberPower MBP60AHVIEC82U User manual

Userˊs Manual
MBP60AHVIEC82U
(Manual Bypass PDU)
Cyber Power Systems,Inc.
www.cyberpower.com K01-C000256-01

CONTENT:
1. SAFETY .......................................................................................... 1
2. MANUAL BYPASS PDU CONTAINS: ............................................. 2
3. BASIC OPERATION........................................................................ 3
3.1. Manual Bypass Schematic .................................................................3
3.2. Front/Rear Panel Description.............................................................3
3.3. Electrical Specifications.......................................................................4
3.4. Operating Environment .......................................................................4
3.5. Dimensions and Weights ....................................................................4
3.6. Hardware Installation...........................................................................5
3.6.1. Rear Installation:.......................................................................5
3.6.2. Rack Installation: ......................................................................5
4. ELECTRICAL INSTALLATION........................................................ 6
5. UPS MAINTENANCE WITH MANUAL BYPASS MODULE ............. 7
5.1. How to remove the UPS with Manual Bypass Module...................7
5.2. How to return the UPS with Manual Bypass Module......................8

1
SAVE THESE INSTRUCTIONS. This manual contains important instructions that
should be followed during installation and maintenance of the Manual Bypass
Module and UPS.
1. SAFETY
The system has its own power source when connected to the UPS (UPS battery).
Consequently, the power outlets may be energized even if the system is
disconnected from the AC power source.
Dangerous voltage levels are present within the system.
It should be opened exclusively by qualified service personnel.
The product must be properly grounded, always connect the earth wire first.
The Manual Bypass Module connection instructions and operation described in
the manual must be followed in the indicated order. Disconnection and over
current protection devices shall be provided by others for AC in/out circuits.
CAUTION - To reduce the risk of fire, the unit connects only to a circuit provided
with branch circuit over current protection (please refer to the UPS User Manual
for current rating).
The upstream circuit breaker must be easily accessible.
The unit can be disconnected from AC power source by opening this circuit
breaker, and if still connected to UPS, by previously shutting down the UPS (refer
to the UPS User Manual).
Check that the indications on the rating plate correspond to your AC powered
system and to the actual electrical consumption of all the equipment to be
connected to the system.
Never install the system near liquids or in an excessively damp environment.
Never let a foreign body penetrate inside the system.
Never expose the system to direct sunlight or source of heat.
If the system must be stored prior to installation, storage must be in a dry place.
All repairs and service should be performed by Authorized Service Personnel only.
There are no user serviceable parts inside the Manual Bypass Module.

2
2. MANUAL BYPASS PDU CONTAINS:
Manual Bypass PDU
User’s Manual
UPS Input Cable(BLUE)
Terminal
UPS Output Cable(GRAY)
Flat Head Screws:
M4X8L*8PCS
Rackmount Ears*2PCS
Round Head Screws:
M3X6L*4PC

3
3. BASIC OPERATION
3.1. Schematic
3.2. Top/Rear Panel Description
①Manual Bypass Switch
The Manual Bypass Module has a manual Bypass rotary switch with two
UPS
LINE
INPUT
OUTPUT
UPS Input
Connector
MANUAL
BYPASS
SWITCH
UPS Output
Connector

4
positions:
UPS → the load is supplied by the UPS.
BYPASS → the load is supplied directly by the AC power source.
②UPS Output Connector
Use the connector to attach the Manual Bypass Module to the UPS Output.
③Input / Output Terminal Block
Connect to utility power / your equipment.
④UPS Input Connector
Use the connector to attach the Manual Bypass Module to the UPS Input.
⑤Output Socket
3.3. Electrical Specifications
Line Input
Phase
Single
Voltage
220~240Vac
Frequency
50/60Hz
Rated Current
60A
Output
Voltage
220~240Vac
Frequency
50/60Hz
Rated Current
60A
3.4. Operating Environment
Temperature
Humidity
Storage
temperature
0℃~40℃
<95%
-15℃~50℃
3.5. Dimensions and Weights
Dimensions W×H×D(mm)
Net Weight(kg)
288*88*141
2.8

5
3.6. Hardware Installation
3.6.1. Rear Installation:
3.6.2. Rack Installation:

6
4. ELECTRICAL INSTALLATION
This type of connection must be carried out by qualified electrical
personnel.
Refer to the UPS User Manual for circuit breaker current rating
and the cable cross-sections, the circuit breaker has to be
installed upstream the Manual Bypass Module Normal AC source
Before carrying out any connection, check that the upstream
protection device (Normal AC source) is open "O"(Off).
Before proceeding to connect the Manual Bypass Module to the UPS,
make sure the UPS has been properly shut down (refer to the UPS user
manual).
Always connect the ground wire first.
1. Install the “UPS Input Cable” “UPS Output Cable”and “Battery Cable” to the UPS
terminals (refer to the UPS User Manual).
2. Open the Cover of Manual Bypass Switch and verify it is on the "UPS" position.
3. according to the following diagram
a) Connect the input and output wires to the Manual Bypass Module terminals
block.
b) Connect the “UPS Input Cable” and “UPS Output Cable” to the corresponding

7
connector.
4. Reinstall all Useful safety protection covers
5. Connect the battery cable (refer to the UPS User Manual).
6. Set the Manual Bypass Module upstream Breaker to the "ON" position.
7. Set the UPS Input Breaker to the "ON" position and verify the UPS is in Bypass
mode.
8. Turn on the UPS (refer to the UPS User Manual).
5. UPS MAINTENANCE WITH MANUAL BYPASS MODULE
This operation allows qualified personnel to remove the detachable Manual Bypass
Module from the UPS for routine maintenance or replacement without disrupting power
to connected equipment.
5.1. How to remove the UPS with Manual Bypass Module
1. Put the UPS in internal “Bypass mode” (refer to the UPS user manual)
2. Verify that the UPS is on Bypass mode by checking UPS Display Panel (refer to
the UPS user manual).
DO NOT OPERATE THE MANUAL BYPASS SWITCH IF THE UPS IS NOT
IN BYPASS MODE
3. Set the Manual Bypass Switch to “BYPASS” position after opening the Switch
Cover.
4. Set the UPS Input Breaker to the "OFF" position and wait a few minutes, the UPS
would shut down.

8
5. UPS stops, the UPS can now be disconnected, as described below:
Disconnect the Battery Cable from Battery module.
Disconnect the UPS Input/Output Cables form the Manual Bypass Module.
6. Replace the UPS.
Hazardous voltage and lost load risk: do not manipulate the Manual
Bypass Switch without UPS connected the Input and Output cables.
5.2. How to return the UPS with Manual Bypass Module
1. Install the “UPS Input Cable” “UPS Output Cable” and “Battery Cable” to the UPS
terminals (refer to the UPS User Manual).
2. Open the Cover of Manual Bypass Switch and check that the Manual Bypass
Switch is on the "BYPASS" position.
3. Connect the Cables to the corresponding connector.
4. Set the UPS Input Breaker to the "ON" position.
5. Verify that the UPS is in Bypass mode by checking display panel (refer to the UPS
User Manual).
DO NOT OPERATE THE MANUAL BYPASS SWITCH IF THE UPS IS NOT
IN BYPASS MODE
6. Set the Manual Bypass Switch to “UPS” position.
7. Turn on the UPS (refer to the UPS user manual).
8. Check the UPS is in Normal mode.
Hazardous voltage and lost load risk: do not manipulate the Manual
Bypass Switch without UPS connected the Input and Output cables.
Cyber Power Systems,Inc.
www.cyberpower.com
6F, No. 32, Sec. 1, Chenggong Rd., Nangang District, Taipei 115, Taiwan
Entire contents copyright©2013 Cyber Power Systems,Inc., All rights reserved. Reproduction in whole
or in part without permission is prohibited. PowerPanel®Business Edition and PowerPanel®
Personal Edition are trademarks of Cyber Power Systems,Inc.