CyberPower OL6000ERT3UP User manual

User’s Manual
OL6000ERT3UP
OL8000ERT3UP
OL10000ERT3UP
OL6000ERT3UM
OL8000ERT3UM
OL10000ERT3UM






CyberPower Systems Inc.
www.cpsww.com





K01‐0000221‐00


Copyright © 2011 CyberPower Systems, Inc.
IMPORTANT SAFETY INSTRUCTIONS
1


This manual contains important instructions. Please read and follow all instructions carefully during installation and operation of the unit. Read this manual
thoroughly before attempting to unpack, install, or operate the UPS.

CAUTION! The UPS must be connected to a grounded AC power
outlet with fuse or circuit breaker protection. DO NOT plug the UPS into
an outlet that is not grounded. If you need to power-drain this equipment,
turn off and unplug the unit.
CAUTION! The battery can power hazardous components inside the
unit, even when the AC input power is disconnected.
CAUTION! The UPS should be placed near the connected equipment
and easily accessible.
CAUTION! To prevent the risk of fire or electric shock, install in a
temperature and humidity controlled indoor area, free of conductive
contaminants. (Please see specifications for acceptable temperature and
humidity range).
CAUTION! (No User Serviceable Parts): Risk of electric shock, do
not remove cover. No user serviceable parts inside. Refer servicing to
qualified service personnel.
CAUTION! (Non-Isolated Battery Supply): Risk of electric shock,
battery circuit is not isolated from AC power source; hazardous voltage
may exist between battery terminals and ground. Test before touching.
CAUTION! To reduce the risk of fire, connect the UPS to a branch
circuit with 40 amperes (OL6000) / 50 amperes (OL8000) / 60 amperes
(OL10000) maximum over-current protection in accordance to CE
requirement.
CAUTION! The AC outlet where the UPS is connected should be close
to the unit and easily accessible.
CAUTION! Please use only VDE-tested, CE-marked mains cable, (e.g.
the mains cable of your equipment), to connect the UPS to theAC outlet.
CAUTION! Please use only VDE-tested, CE-marked power cables to
connect any equipment to the UPS.
CAUTION! When installing the equipment, ensure that the sum of the
leakage current of the UPS and the connected equipment does not
exceed 3.5mA.
CAUTION! The OL6000 / OL8000 / OL10000 models are
permanently-connected equipment and only qualified maintenance
personnel may carry out installations.
CAUTION! Do not unplug the unit from AC Power during operation, as
this will invalidate the protective ground insulation.
CAUTION! To avoid electric shock, turn off and unplug the unit before
installing the input/output power cord with a ground wire. Connect the
ground wire prior to connecting the line wires!
CAUTION! Do not use an improper size power cord as it may cause
damage to your equipment and cause fire hazards.
CAUTION! Wiring must be done by qualified personnel.
CAUTION! DO NOT USE FOR MEDICAL OR LIFE SUPPORT
EQUIPMENT! Under no circumstances this unit should be used for
medical applications involving life support equipment and/or patient care.
CAUTION! DO NOT USE WITH OR NEAR AQUARIUMS! Toreduce
the risk of fire, do not use with or near aquariums. Condensation from
the aquarium can come in contact with metal electrical contacts and
cause the machine to short out.
CAUTION! Do not dispose of batteries in fire as the battery may
explode.
CAUTION! Do not open or mutilate the battery, released electrolyte is
harmful to the skin and eyes.
CAUTION! Abattery can present a risk of electric shock and high short
circuit current. The following precaution should be observed when
working on batteries
1. Remove watches, rings or other metal objects.
2. Use tools with insulated handles.
CAUTION! The unit has a dangerous amount of voltage. When the
UPS indicators is on, the units may continue to supply power thus the
unit’s outlets may have a dangerous amount of voltage even when it’s not
plugged in to the wall outlet.
CAUTION! Make sure everything is turned off and disconnected
completely before conducting any maintenance, repairs or shipment.
CAUTION! Connect the Protection Earth (PE) safety conductor before
any other cables are connected.
WARNING! (Fuses): To reduce the risk of fire, replace only with the
same type and rating of fuse.
DO NOT INSTALL THE UPS WHERE IT WOULD BE EXPOSED TO
DIRECT SUNLIGHT OR NEARA STRONG HEAT SOURCE!
DO NOT BLOCK OFF VENTILATION OPENINGS AROUND THE
HOUSING!
DO NOT CONNECT DOMESTIC APPLIANCES SUCH AS HAIR
DRYERS TO UPS OUTPUT SOCKETS!
SERVICING OF BATTERIES SHOULD BE PERFORMED OR
SUPERVISED BY PERSONNEL KNOWLEDGE OF BATTERIES AND
THE REQUIRED PRECAUTIONS. KEEP UNAUTHORIZED
PERSONNEL AWAY FROM BATTERIES!



Copyright © 2011 CyberPower Systems, Inc.
UNPACKING

2
Power module

PDU or HW PDU with Manual Bypass
User’smanual Registercard
Rackmount left rail Rackmount right rail
Phone line
USB communication cable
Serial Interface Cable (RS-232)
Battery module
Rack mount ears (Stands) (2) * 2 sets
Tie plate (1) * 2 sets
Flat head screws:M5X8L (8) * 2 sets
Pan head screws:M5X12L (12) * 2 sets
Plastic washers (8) * 2 sets
Screw hole dust covers (10) * 2 sets
Power cord
PowerPanel® Business Edition software CD



Copyright © 2011 CyberPower Systems, Inc.
HARDWARE INSTALLATION


HARDWARE INSTALLATION
These versatile UPS systems can be mounted in a rackmount or vertical
tower orientation. This versatility is especially important to growing
organizations with changing needs that value having the option to
position a UPS on a floor or in a rackmount system. Please follow the
instructions below for the respective mounting methods.
SAFETY PRECAUTIONS
CAUTION! To prevent the risk of fire or electric shock, only use the
supplied hardware to attach the mounting brackets.
RACKMOUNT INSTALLATION
Step 1: Remove the internal battery trays from the Battery module
(See page 19)
Step 2: Rackmount ears installation
Attach the two rackmount ears to the Battery module using the provided
screws M5X8L*8pcs.
Step 3: Rackmount rail Installation
The rails adjust to mount in 48-cm (19-inch) panel racks from 52 to
91.5cm (20.5 to 36 inches) deep. Select the proper holes in the rack for
positioning the Battery module in the rack. The Power module or the
Battery module takes up position 1 through position 9.
Step 4: Adjust rackmount rails to fit your rack
Attach the rackmount rail to your rack with two M5X12L screws and two
plastic washers at the front of the rack. (Located in position 1 & position 6)
Do not tighten the screws. Adjust the rail size on the rail assembly of your
rack. Secure the rail to the rear of the rack with two M5X12L screws and
two plastic washers. Tighten all screws at the front and rear of the rail.
Once completed, perform the same steps for assembling the other
rackmount rail.
Place the Battery module on a flat stable surface with the front of the unit
facing toward you. Secure the Battery module to your rack with four
M5X12L screws at the front of the rack. (Located in position 2 & position
8)
Step 5: Place the internal battery trays back into the Battery module
(See page 19)
Once completed, perform the same steps for the Power module.
CAUTION! The Battery module must be installed below the Power
module.
3


Copyright © 2011 CyberPower Systems, Inc.
HARDWARE INSTALLATION

VERTICAL/TOWER INSTALLATION
Step 1: Rotate the Multifunction LCD Module
Unscrew the right panel of the Power module. Separate the right panel
from the UPS. Gently lift the LCD module out. Rotate it to the tower
orientation. Reinstall it for a tower configuration.
Step 2: Attach the base stands
Secure the tie bracket with the screws (M5X8*4pcs). Tighten the screws
(M5X12*4pcs) of the base stands (rackmount ears) onto the bottom of
the power module and the battery module.
Step 3: Attach dust covers
Insert dust covers into the rackmount ear screw holes that are not being
used.

ELECTRICAL INSTALLATION
After completing the hardware installation of the UPS, you are now ready
to plug in the UPS and connect your equipment.




4


Copyright © 2011 CyberPower Systems, Inc.
HARDWARE INSTALLATION
PDU or HW PDU INSTALLATION
Step 1: Remove the cover from the PDU’s
Loosen the two screws and remove the cover from the PDU’s to expose
the connectors.
5
Step 2: Attach the PDU’s to the Power module
Align the connectors of the PDU’s with the connectors of the Power
module to attach the device.
Step 3: Screw the PDU’s
Secure the PDU’s to the Power module with four screws.
ELECTRICAL INSTALLATION
After completing the hardware installation of the UPS, you are now ready
to plug in the UPS and connect your equipment.

SAFETY PRECAUTIONS
CAUTION! Installation environment should be in a temperature and
humidity controlled indoor area free of conductive contaminants. Do not
install this UPS where excessive moisture or heat is present (Please see
specifications for acceptable temperature and humidity range).
CAUTION! Never install a UPS, or associated wiring or equipment,
during a lightning storm.
CAUTION! Do not work alone under hazardous conditions.
CAUTION! In case of the risk of electric shock, do not remove the top
cover.
CAUTION! The battery can energize hazardous live parts inside even
when theAC input power is disconnected.


Copyright © 2011 CyberPower Systems, Inc.
INSTALLING YOUR UPS SYSTEM

SYSTEM BLOCK DIAGRAM



HARDWARE INSTALLATION GUIDE
1. Battery charge loss may occur during shipping and storage. Before
using the UPS, it’s strongly recommended to charge batteries for four
hours to ensure the batteries’ maximum charge capacity. To recharge the
batteries, simply plug the UPS into anAC outlet.
2. When using the included software, connect either the serial or the
USB cable between the computer and the corresponding port on the UPS.
Note: If the USB port is used, the serial port will be disabled. They cannot
be used simultaneously. After connecting to either the USB port or the
Serial port on the UPS, a computer with the PowerPanel®Business
Edition Agent software installed can control the operating schedule,
battery test, outlets, as well as obtain UPS status information. However,
other computers with PowerPanel®Business Edition Client software can
only obtain UPS status information via LAN connection.
3. Connect your computer, monitor, and any externally-powered data
storage device (Hard drive, Tape drive, etc.) into the outlets only when
the UPS is off and unplugged. DO NOT plug a laser printer, copier, space
heater, vacuum, paper shredder or other large electrical device into the
UPS. The power demands of these devices will overload and possibly
damage the unit.
4. To protect a fax machine, telephone, modem line or network cable,
connect the telephone or network cable from the wall jack outlet to the
jack marked “IN” on the UPS and connect a telephone cable or network
cable from the jack marked “OUT” on the UPS to the modem, computer,
telephone, fax machine, or network device.
5. Press the ON/OFF switch to turn the UPS on. The Power-On indicator
light will display when activated. If an overload is detected, an audible
alarm will sound and the UPS will continuously emit two beeps per
second. For resetting the unit, unplug some equipment from the outlets.
Make sure your equipment carries a load current within the unit’s safe
range, (refer to the technical specifications).
6. This UPS is equipped with an auto-charge feature. When the UPS is
plugged into an AC outlet, the battery will automatically charge, even
when the unit is switched off.
7. To maintain an optimal battery charge, leave the UPS plugged into an
AC outlet at all times.
8. Before storing the UPS for an extended period of time, turn the unit
OFF. Then cover it and store it with the batteries fully charged. Recharge
the batteries every three months to ensure good battery capacity and
long battery life. Maintaining a good battery charge will help prevent
possible damage to the unit from battery leakage.
9. The UPS has one USB port (default) and one Serial port that allows
connection and communication between the UPS and any attached
computer running the PowerPanel®Business Edition Agent software. The
UPS can control the computer’s shutdown during a power outage
through the connection while the computer can monitor the UPS and alter
various programmable parameters. Note: Only one communication port
can be used at a time. The port not in use will automatically become
disabled or the serial port will be disabled if both ports are attached.
10. EPO (Emergency Power Off) Port:
EPO ports allow administrators the capability to connect the UPS unit to
customer-supplied EPO switches. These installations give operators a
single access point to immediately power-off all equipment connected to
the UPS during an emergency.
11. To avoid electric shock, turn the unit OFF and disconnect the unit
from utility power before hardwiring the UPS (in/out power cord). The
in/out power cord MUST be grounded.
6


Copyright © 2011 CyberPower Systems, Inc.
HARDWIRING THE INPUT/ OUTPUT TERMINALS


CHECK CIRCUIT BREAKER/WIRING
Check branch circuit breaker rating and wiring dimensions with the following table.
UPS Capacity Branch Circuit Breaker Wiring AWG Wiring mm2
6KVA 40A 10 AWG 5.5 mm2
8KVA 50A 8 AWG 8.0 mm2
10KVA 60A 6 AWG 14.0 mm2
INPUT/ OUTPUT CONFIGURATION
Hardwire the input/output terminals as shown in the following diagram.
SAFETY PRECAUTIONS
CAUTION! Input and Output circuit breakers must be “OFF” during the building installation.
CAUTION! An additional two pole disconnect device is necessary during the building installation.
CAUTION! Disconnected EPO will immediately shut down the logic circuit output of the UPS. Wiring the EPO signal is optional.
CAUTION! Local safety rules may require a separate, external EPO to turn off output circuit breakers. Refer to local wiring rules, the EPO should use
approved components.
Step 1: Remove the inspection window cover
Loosen the four screws to remove the inspection window cover.
7
Step 2: Remove the terminal block cover
Loosen the four screws to remove the terminal block cover.



Copyright © 2011 CyberPower Systems, Inc.
HARDWIRING THE INPUT/ OUTPUT TERMINALS
Step 3: Input configuration
Insert the input cable through the appropriate cable gland (not included)
and connect the three wires to the input terminal block.
8
Step 4: Output configuration
Insert the output cable through the appropriate cable gland (not included)
and connect the three wires to the output terminal block.
Step 5: Fix the terminal block cover on the PDU’s
Tighten the four screws to fix the terminal block cover on the PDU’s.
Step 6: Fix the inspection window cover on the PDU’s
Tighten the four screws to fix the inspection window cover on the PDU’s.


Copyright © 2011 CyberPower Systems, Inc.
BACKFEED PROTECTION


BACKFEED PROTECTION OPERATION
1. If the Bypass circuit is shorted and the UPS is running in Line Mode or Battery Mode, backfeed protection will be active and the external isolation device
(Magnetic Contactor) will open.
2. Save your data and perform a controlled shutdown.
3. Contact CyberPower for repair.
WITHOUT BACKFEED PROTECTION CONFIGURATION
1. Hardwire the input terminals as shown in the following diagram.
2. Do not remove the interconnection wires (Jumper1 / Jumper2) on “Backfeed Protection Connector”.
WITH BACKFEED PROTECTION CONFIGURATION
1. Customers should provide an external isolation device (Magnetic Contactor) which is upstream and outside the UPS and capable of supporting the UPS
input current.
2. Remove the interconnection wires (Jumper1 / Jumper2) on “Backfeed Protection Connector”.
3. Hardwire the input terminals and “Backfeed Protection Connector” as shown in the following diagram.
4. The external isolation device must be installed in the Mains path.

9


Copyright © 2011 CyberPower Systems, Inc.
BASIC OPERATION


POWER MODULE FRONT/REAR PANEL DESCRIPTION



OL6KERT3UPDUPM / OL8KERT3UPDUPM / OL10KERT3UPDUPM

1. Power Button / Power on Indicator
Master ON/OFF for the UPS. Indicates that the UPS is on and supplying
power.
2. UPS Status / Fault / Replace Battery LED Indicator
Indicates the status of the UPS whether is operating in Line, Battery or
Bypass Mode, or the UPS has an internal fault and the battery need to be
replaced.
3. Multifunction LCD Readout
Shows UPS status, information, settings and events.
4. Function Buttons
Scroll up, scroll down, select and cancel LCD menu.
5. USB port
This is a connectivity port which allows communication and control
between the UPS and the connected computer. It is recommended to
install the PowerPanel® Business Edition Agent software on the
PC/Server connected with the USB cord.
6. Serial Port
Serial port provides communication between the UPS and the computer.
The UPS can control the computer’s shutdown during a power outage
through the connection while the computer can monitor the UPS and alter
its various programmable parameters.
7. Remote Control Port
Connects to remote LCD module to the UPS.
8. Surge Protected Communication Ports RJ-45/RJ-11
These ports are used to protect standard RJ-45/RJ-11 based products
(ADSL, LAN, Phone/ Modem-Lines) and cabling systems from surges.
9. Relay Output Connector
Convert UPS signals into real potential-free Dry Contacts for industrial
control.
10. SNMP/HTTP Network slot
Slot to install the optional SNMP card for remote network control and
monitoring.
11. Backfeed Protection Connector
Prevents power feedback from the inverter to utility power in case of
power failure and a fault in the bypass circuit.
12. EPO (Emergency Power Off) Connector
Enables an emergency UPS Power-Off from a remote location.
13. Extended Runtime Battery Module Connector
Connection for additional CyberPower XLBattery modules.
14. Input / Output Connectors
Use these connectors to attach the PDU or HW PDU to the Power
module.
10


Copyright © 2011 CyberPower Systems, Inc.
BASIC OPERATION

PDU / HW PDU FRONT/REAR PANEL DESCRIPTION


OL6KE6UPDU OL8K10KE6UPDU

OL6K3UPDUHW OL8K10K3UPDUHW

1. Input Circuit Breaker
Provides input overload and fault protection.
2. Manual Bypass Switch
Provide UPS output to connected equipment when turned to Normal.
Provide utility power to connected equipment when turned to Bypass.
3. Input / Output Terminal Block
Connect to utility power / your equipment.
4. Interlock Bracket
Avoid turning the “Manual Bypass Switch“ under normal operation.
5. Inspection Window
Visual check the wiring condition and secure the terminal.
6. Input / Output Connectors
Use these connectors to attach the PDU or HW PDU to the Power
module.
7. Connectors Cover
Provides safety protection when removing the PDU or HW PDU.
8. Output Circuit Breaker
Provides output overload and fault protection.
9. Battery Backup & Surge Protected Outlets
Provides battery backup and surge protection. They ensure power is
provided to connected equipment over a period of time during a power
failure.
Critical / Noncritical Load
Allows the creation of load priorities to ensure that battery power
reserves are transferred to specified outlets during a power outage. The
unit can be programmed to provide additional runtime for equipment
connected to the “CRITICAL” outlets, while stopping the power supply to
equipment connected to “NONCRITICAL” outlets after a designated
period of time.
11


Copyright © 2011 CyberPower Systems, Inc.
BASIC OPERATION

BATTERY MODULE FRONT/REAR PANEL DESCRIPTION
1. On-board Replaceable Fuse Cover
12
Replaceable fuse is accessible from the rear panel. It must
be done by qualified personnel.
2.AC Circuit Breaker
Provides overload and fault protection.
3.AC Output Outlet
Use this outlet to connect to the AC Input Inlet of a
downstream Battery module.
4.AC Input Inlet (Charge Only)
AC power connectivity to wall receptacle.
5. Input Connector
Use this input connector to daisy chain the next Battery
module. Remove the connector cover for access.
6. Output Cable
Use this output cable to connect the Battery module to the
Power module or to the next Battery module.
BPE240V30ART3U / BPE240V50ART3U
CONNECTION #1 : POWER MODULE WITH ONE BATTERY MODULE
Step 1: Loosen the two screws to remove the battery cable
retention bracket of the power module.
Step 2: Use the output cable of the Battery module to connect
the Battery module to the Power module.
Step 3: Rotate the battery cable retention bracket and tighten
the two screws to fix battery cable.
Step 4: Use a power cord to plug AC input inlet of the battery
module into a wall receptacle.


Copyright © 2011 CyberPower Systems, Inc.
BASIC OPERATION

CONNECTION #2 : POWER MODULE WITH MULTIPLE BATTERY MODULES
Step 1: Connect the 1st Battery module to the Power module
using the instructions above.
13
Step 2: Loosen the two screws to remove the battery cable
retention bracket of the 1st battery module.
Step 3: Use the output cable of the 2nd Battery module to
connect the 2nd Battery module to the 1st Battery
module.
Step 4: Rotate the battery cable retention bracket and tighten
the two screws to fix battery cable.
Step 5: Use a power cord to plug AC input inlet of the 2nd battery
module into AC output outlet of the 1st Battery module.






Copyright © 2011 CyberPower Systems, Inc.
OPERATION INSTRUCTIONS FOR LCD MODULE



LED INDICATORS – UPS STATUS
LED Indicators Color UPS Status Description
ON/OFF Blue UPS power is on.
ON-LINE Green UPS is operating in Line Mode.
BATTERY ON Yellow UPS is operating in Battery Mode.
BYPASS Yellow UPS is operating in Bypass Mode, Manual Bypass or ECO (Economy) Mode.
FAULT Red UPS has an internal fault. See “Trouble Shooting” for additional information.
REPLACE BATTERY Red Battery will soon need to be replaced due to insufficient runtime.


LCD SCREEN – UPS STATUS
LCD Screen UPS Status Description
Line Mode UPS is operating in Line Mode.
Battery Mode UPS is operating in Battery Mode.
Bypass Mode UPS is operating in Bypass Mode.
Manual Bypass UPS is operating in Manual Bypass.
ECO Mode UPS is operating in ECO (Economy) Mode.


BUTTON OPERATION
Button Operation Description
ON/OFF Press this button to turn on or turn off UPS.
▲Press this button to scroll up in the LCD menu.
▼Press this button to scroll down in the LCD menu.
ENTER Press this button to select an option.
ESC Press this button to cancel or return to previous LCD menu.
14


Copyright © 2011 CyberPower Systems, Inc.
LCD SETUP FUNCTIONS
15

MULTI-FUNCTION LCD MAIN MENU
Press “Enter” button to activate “MAIN MENU”.
MAIN MENU submenu Function Description
Information Displays the UPS information.
Configure Displays the UPS settings that can be configured by the user.
Event Log Displays the 3 most recent events, by event count, time
(day/hour/minute), and event description.

LCD INFORMATION READOUT
There are 19 types of UPS information available for display.
1. Press the “ENTER” button to activate the “MAIN MENU”.
2. Press the “▲” and “▼” buttons to scroll to the “Information” option.
3. Press the “ENTER” button to select the “Information” submenu.
4. Press the “▲” and “▼” buttons to scroll through the “Information” submenu in the following table.
5. Press the “ESC” button to return to UPS Status.
Information Submenu Description
O/P Volt = XXX.XV Displays the Output Voltage
O/P Freq = XX.XHz Displays the Output Frequency
I/P Volt = XXX.XV Displays the Input Voltage
I/P Freq = XX.XHz Displays the Input Frequency
O/P Load = XXX% Displays the Output Load Percentage of Maximum load
O/P Amp = X.XA Displays the Output Current
O/P Watt =XXXXXW Displays the Output Wattage
O/P VA =XXXXXVA Displays the Output VA
BAT Volt = XXX.XV Displays the Battery Voltage
BAT Cap = XXX% Displays the Estimated Percentage of Battery Capacity
BAT Runtime=XXXM Displays the Estimated Battery Runtime in Minutes
EBM Number= X Displays the External Battery Module Number
TEMP =XX°C / XXX°F Displays the Approximate inside Temperature in both ℃(Celsius) and ℉
(Fahrenheit) for the UPS
SBM = XXXXX Displays the Stage of Smart Battery Management
Rating = XXK VA Displays the UPS Rating
MCU Ver = XXXX Displays the MCU Firmware Version
Model Name Displays the UPS Model Name
Date & Time
- - - - / - - / - - - -:- - Displays the present Date & Time
Next BAT Change
XXX/XXXX Displays the next Battery Change Date & Time


Copyright © 2011 CyberPower Systems, Inc.
LCD SETUP FUNCTIONS
16

LCD EVENT LOG
3Event Logs of UPS can be recorded.
1. Press the “ENTER” button to activate the “MAIN MENU”.
2. Press the “▲” and “▼” buttons to scroll to the “Event Log” option.
3. Press the “ENTER” button to select the “Event Log” submenu.
4. Press the “▲” and “▼” buttons to scroll through the “Event Log” submenu in the following table.
5. Press the “ESC” button to return to UPS Status.
Event Log Submenu Description
(X) XXDXXHXXM (without PowerPanel® Business or RMCARD302)
- - / - - - -:- - (with PowerPanel® Business or RMCARD302)
Event Content
MULTI-LANGUAGE INTERFACE
Users can configure 1 of the 3 available languages for display.
([English], [Español-Spanish], [Français-French])
1. Press the “ENTER” button to activate the “MAIN MENU”.
2. Press the “▲” and “▼” buttons to scroll to the “Configure” option.
3. Press the “ENTER” button to select the “Configure” submenu.
4. Press the “▲” and “▼” buttons to scroll through the “Language” options.
5. Press the “ENTER” button to select the “Language” submenu.
6. Press the “▲” and “▼” buttons to scroll to the language that you want to select.
You may be prompted to save the selection, if so press the “ENTER” button to save the setting.
7. Press the “ESC” button to cancel or return to previous LCD menu.

LCD SETTINGS CONFIGURATION
There are 20 UPS settings that can be configured by the user.
1. Press the “ENTER” button to activate the “MAIN MENU”.
2. Press the “▲” and “▼” buttons to scroll to the “Configure” option.
3. Press the “ENTER” button to select the “Configure” submenu.
4. Press the “▲” and “▼” buttons to scroll to the “Configure” submenu in the following table.
5. Press the “ENTER” button to select the setting you want to configure.
The first configuration parameter will be displayed on the second column of LCD screen.
6. Press the “▲” and “▼” buttons to scroll through the different parameters.
7. Press the “ENTER” button to select the parameter you want to change.
You may be prompted to save the selection, if so press the “ENTER” button to save the setting. Some options are saved
and started automatically. (See the following table for additional details.)
8. Press the “ESC” button to cancel or return to the previous LCD menu.


Copyright © 2011 CyberPower Systems, Inc.
LCD SETUP FUNCTIONS
17

Configure Submenu Available Settings Default Setting
Output Voltage = [200V] [208V] [220V] [230V] [240V] 230V*
Sync Freq Window Range= [+/- 1%] [+/- 2%] [+/- 3%] [+/- 4%] [+/- 5%]
[+/- 6%] [+/- 7%] [+/- 8%] [+/- 9%] [+/-10%] +/- 5%
Bypass V Window Range= [+10%/-10%] [+10%/-15%] [+10%/-20%]
[+15%/-10%] [+15%/-15%] [+15%/-20%] +10%/-15%
Bypass Condition [Check Freq/Volt] [Check Volt Only] [No Bypass] Check Freq/Volt
ECO Mode** [Disable] [Enable] Disable
[V Range= +/-15%] [V Range= +/-10%] (for [Enable]) V Range= +/-10%
Manual Bypass [Disable] [Enable] Disable
Battery Test [Activate?] None
Audible Alarms [Disable] [Enable] Enable
EBM Number = [0] [1] [2] [3] [4] [5] [6] [7] [8] [9] [10] 0
Wiring Fault [Disable] [Enable] Enable
NCL Control [Outlet On] [Outlet Off] Outlet On
Language [English] [Deutsch-German] [Français-French] English
Generator Mode*** [Disable] [Enable] Disable
Communication [Disable] [Enable] Enable
Dry Relay Set [I/P Power Fail] [Battery Low] [Summary Alarm]
[UPS On Bypass] [UPS Fail] I/P Power Fail
Converter Mode**** [Converter Off] [O/P Freq = 50Hz] [O/P Freq = 60Hz] Converter OFF
Screen Saver [Disable] [1 Minutes] [5 Minutes] 5 minutes
Clear Event Log [Activate?] None
Button OFF LOCK [Disable] [Enable] Disable
Charger Function [SBM] [Constant] SBM
*) Output voltage default setting depends on different nation or order requested.
**) This function can’t be set when Manual Bypass, Generator Mode or Converter Mode is enabled.
***) UPS has no bypass when Generator Mode is enabled.
****) UPS has no bypass when Converter Mode is enabled. This function can only be set before the UPS is on.
SILENCING AUDIBLE ALARMS
1. Press any of four function buttons on the LCD module; Note: the alarm can not be turned off for a “Battery Low”
condition. This condition will still result in an audible alarm.
2. Configure “Audible Alarms” as “Disable” on the LCD module and it will stop warning of any malfunction audibly.
MANUAL BATTERY TEST
Configure “Battery Test” as “Active” on the LCD module; and it will perform the “Manual Battery Test”


Co


RE
M
Step
Unsc
r
from
t
Step
Conn
Por
t
SA
F
CAU
T
CAU
T
p
yright ©
2
LC
D
M
OTE CON
T
1: Remove the
M
r
ew the right pa
n
t
he UPS. Gently
2: Connect the
ect the DB26 c
a
t
”on the front pa
n
F
ETY PREC
A
T
ION! It must
b
T
ION! To avoi
d
2
011 Cybe
r
D
MODUL
E
T
ROL
M
ultifunction L
C
n
el of the Powe
r
lift the LCD mod
u
DB26 Cable
a
ble from LCD
m
n
el or rear panel
A
UTION
S
b
e done by quali
f
d
electric shock,
t
r
Power S
y
E
REMOT
E
C
D Module
r
module. Separ
a
u
le out. Reinstall
m
odule to the “R
as shown in the
f
ied personnel.
t
urn off and unpl
u
y
stems, In
c
E
CONTR
O
a
te the right pa
n
the right panel.
emote Contr
o
following figure.
u
g the unit befor
e
c
. 
O
L and
W
18
n
el
o
l
W
A
Ste
p
Uns
c
fro
m
Ste
p
Ste
p
Con
n
Po
r
Ste
p
e
installing REM
O
W
A
LL-MO
U
A
LL-MOUN
T
p
1: Remove th
e
c
rew the right p
a
the UPS. Gentl
y
p
2: Rotate the
D
p
3: Connect th
e
n
ect the DB26
c
r
t”on the front p
a
p
4: Mount LCD
O
TE CONTROL
o
U
NTING IN
T
ING INSTR
U
e
Multifunction
L
a
nel of the Pow
e
y
lift the LCD mo
d
D
B26 Connecto
r
e
DB26 Cable
c
able from LCD
m
a
nel or rear pan
e
Module on the
W
o
r WALL-MOUN
T
STRUCTI
O
U
CTION
S
L
CD Module
e
r module. Sepa
d
ule out. Reinst
a
r
of LCD Modul
e
m
odule to the “
R
e
l as shown in th
e
W
all
O
NS
T
ING INSTRUC
T
rate the right p
a
a
ll the right panel
.
e
R
emote Cont
r
e
following figure
T
IONS.
a
nel
.
r
ol
.
p


Copyright © 2011 CyberPower Systems, Inc.
MAINTENANCE


Storage
To store your UPS for an extended period, cover it and store with the
battery fully charged. Recharge the battery every three months to ensure
battery life.
Battery Replacement
Please read and follow the Safety Instructions before servicing the
battery. Battery replacement should be performed by trained personnel
who are familiar with the procedures and safety precautions. Make a note
of the replacement Battery module number.
Safety Precautions
CAUTION! Only use replacement batteries which are certified by
CyberPower Systems. Use of incorrect battery type is an electrical
hazard that could lead to explosion, fire, electric shock, or short circuit.
CAUTION! Batteries contain an electrical charge that can cause
severe burns. Before servicing batteries, please remove any conductive
materials such as jewelry, chains, wrist watches, and rings.
CAUTION! Do not open or mutilate the batteries. Electrolyte fluid is
harmful to the skin/eyes and may be toxic.
CAUTION! To avoid electric shock, turn off and unplug the UPS from
the wall receptacle before servicing the battery.
CAUTION! Only use tools with insulated handles. Do not lay tools or
metal parts on top of the UPS or battery terminals.
Replacement Batteries
Please refer to the front side of the Battery module for the model number
of the correct replacement batteries. For battery procurement, log onto
www.CPSww.com, or contact your local dealer.
Battery Disposal
Batteries are considered hazardous waste and must be disposed of
properly. Contact your local government for more information about
proper disposal and recycling of batteries. Do not dispose of batteries
in fire.



Battery Installation
19
Step 1: Remove the front panels Step 2: Remove the retaining screws from
the cable protection cover and then remove
the cover itself

Step 3: Pull the battery trays out slowly and
then put the new battery trays back into the
compartment


Step 4: Insert the battery connectors and tighten the screws of battery retaining cover



Step 5: Install the front panels