D-Link DGE-660TD User manual

D-Link DGE-660TD Installation Guide 2
This Installation Guide includes instructions for:
• Windows Vista™
• Windows®XP
• Windows®2000
Installation Guide Contents
Section 1: Pre-Installing the Windows®Vista™, XP, and 2000
Section 2: Insert the DGE-660TD into your Laptop
Section 3: Finishing the Windows®Installation
Package Contents
Verify that your D-Link DGE-660TD package contains the
following items. If any items are missing, please contact your
reseller.
• D-Link DGE-660TD
• Drivers on CD-ROM
• Manual on CD-ROM
!For Windows®Vista/XP/2000:
Run the Install CD BEFORE installing the
DGE-660TD into your laptop.

D-Link DGE-660TD Installation Guide3
Installing the Driver
• With your computer ON, insert the Driver CD of the
DGE-660TD into your CD-ROM Drive.
• The Autorun Screen will appear as shown here.
• Select “Install Drivers” to install the drivers onto your
computer.
• After a few moments, the “Install Finish” screen will appear.
Click “OK”.
• Select “Yes,” if you are prompted to restart your computer.
Restart the computer manually if the prompt does not occur.
(Go to Start > Shut down > Restart.)

D-Link DGE-660TD Installation Guide 4
Insert the Adapter
This section refers to all users, regardless of which operating
system you use.
NOTE: You must first install the drivers as explained in
Section 1.If you have not done this and you have inserted the
DGE-660TD into the Cardbus slot, you will need to cancel
the New Hardware Wizard, and start over at the beginning
of this installation guide.
• Insert the DGE-660TD into the Cardbus slot of your laptop.
• Gently insert the front end of the DGE-660TD into the Cardbus
slot on your laptop until it is firmly seated. Make sure that the
card is face-up, as shown. Do not force the insertion.
• Connect an Ethernet Cable (CAT5) from a switch or hub to
the DGE-660TD.

D-Link DGE-660TD Installation Guide5
Finishing the Installation
To complete the installation of the DGE-660TD:
• Make sure that the DGE-660TD CD-ROM is
inserted in the CD-ROM drive
• The DGE-660TD is inserted into your laptop
• The laptop is turned ON
• See the section below that corresponds to your
Operating System to complete the installation:
Windows Vista™Users
Windows Vista™completes the installation of the DGE-660TD
automatically. An “Installing device driver software” message
will appear in the task bar to indicate that the installation is in
progress.

D-Link DGE-660TD Installation Guide 6
Windows®XP Users
Windows®XP completes the installation of the DGE-660TD
automatically. A “Found New Hardware” message will appear in
the task bar to indicate that the installation is complete.
Windows®2000 Users
Windows®2000 completes the installation of the DGE-660TD
automatically. When the “hour glass” disappears, the installation
is complete.

D-Link DGE-660TD Installation Guide7
Verify Installation
Step 1:
Windows®2000: Click on Start > Settings > Control Panel
Windows®XP: Click on Start > Control Panel
Windows Vista™: Click on Start > Control Panel
Step 2:
Windows®2000 and XP: Click on the System icon. Click the
Hardware tab and then click Device Manager.
Windows Vista™: Click on System and Maintenance and then
click on Device Manager.
Step 3:
Scroll down and click the plus (+) sign next to Network Adapters.
The D-Link DGE-660TD Gigabit CardBus PC Card will be
listed.

D-Link DGE-660TD Installation Guide 8
Configure your Adapter
After you install your new D-Link adapter, by default, the TCP/IP
settings should be set to obtain an IP address from a DHCP
server (i.e router) automatically. To verify your IP address,
please see follow the steps below:
Windows®2000/XP: Click on Start > Run. In the run box type
cmd and click OK.
Windows Vista™: Click on Start > All Programs > Accessories
> Command Prompt.
At the prompt, type ipconfig and press Enter.
This will display the IP address, subnet mask, and the default
gateway of your adapter.
If the address is 0.0.0.0, check your adapter installation, security
settings, and the settings on your router. Some firewall software
programs may block a DHCP request on newly installed
adapters.

D-Link DGE-660TD Installation Guide9
If you are not using a DHCP capable gateway/router, or you need
to assign a static IP address, please follow the steps below.
Step 1
Windows®2000: Click on Start > Settings > Control Panel >
Network Connections.
Windows®XP : Click on Start > Control Panel > Network
Connections.
Windows Vista™: Click on Start > Control Panel > Network and
Internet > Network and Sharing Center > Manage network
connections.
Step 2
Right-click on Local Area Connection which represents your
D-Link network adapter and select Properties.
Step 3
Highlight Internet Protocol (TCP/IP) and click Properties.
Step 4
Click Use the following IP address and enter an IP address
that is on the same subnet as your network or the LAN IP
address on your router.

D-Link DGE-660TD Installation Guide 10
Example: If the router’s LAN IP address is 192.168.0.1, make
your IP address 192.168.0.X where X is a number between 2
and 99. Make sure that the number you choose is not in use
on the network. Set Default Gateway the same as the LAN IP
address of your router (192.168.0.1).
Set Primary DNS the same as the LAN IP address of your router
(192.168.0.1). The Secondary DNS is not needed or you may
enter a DNS server from your ISP.
Step 5
Click OK twice to save your settings.