D-Link DCS-4705E User manual

This document will guide you through the
basic installation process for your new
D-Link Network Camera.
DCS-4705E
Vigilance 5 Megapixel H.265 Outdoor Bullet Camera
Quick Installation Guide
Краткое руководство по установке
КОРОТКИЙ ПОСІБНИК ЗІ ВСТАНОВЛЕННЯ
5 Мп внешняя сетевая камера, день/ночь,
с ИК-подсветкой до 30 м, РоЕ и WDR

1
D-Link DCS-4705E Quick Installation Guide 1
ENGLISH
Quick Installation Guide
This installation guide provides basic instructions for installing the Network
Camera on your network. For additional information about how to use the
camera, please see the User Manual which is available on the CD included in
this package or from the D-Link support website.
Package Contents
DCS-4705E Vigilance 5 Megapixel H.265 Outdoor Bullet Camera
Cable Waterproofing Connector
Rubber Power Connector Plug
Mounting Kit
Manual and Software on CD-ROM
Quick Installation Guide
If any of the above items are missing, please contact your reseller.
Safety Notice:
Installation and servicing should be done by certified technicians so as to
conform to all local codes and prevent voiding your warranty.

2D-Link DCS-4705E Quick Installation Guide
2
ENGLISH
Hardware Overview
Camera Lens
IR LEDs
Provide illumination for
low-light environments
Adjustment Ring
Loosen to adjust camera
angle and tighten to lock
camera angle
Reset Button
Press and hold for 10
seconds to reset camera
back to the factory default
settings
Grounding Screw
Can be attached to a
grounding wire if desired
Power Connector
Connects to an optional 12 V / 1.5 A power
adapter (not included)
Ethernet Jack
RJ-45 connector for Ethernet, can
also be used to power the camera
using Power over Ethernet (PoE)

3
D-Link DCS-4705E Quick Installation Guide 3
ENGLISH
Configuring the Camera
Insert the DCS-4705E CD into your computer's CD-ROM drive to begin
the installation. If the Autorun function on your computer is disabled, or if
the D-Link Launcher fails to start automatically, click Start > Run. Type D:\
autorun.exe, where D: represents the drive letter of your CD-ROM drive.
Click on the D-Link Setup Wizard SE icon that
was created in your Windows Start menu (Start >
D-Link > Setup Wizard SE).
The Setup Wizard will appear and display the MAC
address and IP address of your camera(s). If you
have a DHCP server on your network, a valid IP
Address will be displayed. If your network does not
use a DHCP server, the network camera's default
static IP 192.168.0.20 will be displayed.
Select your camera, then click the Wizard button to
continue.
Click Setup Wizard and follow the instructions to
install the Setup Wizard.
Enter the Admin ID and password. When logging in
for the first time, the default Admin ID is admin with
the password left blank.
Click the checkboxes if you wish to change the
admin ID and password for the camera, and enter
the new ID and password you wish to use.
Click Next to continue.
Select DHCP if your camera obtains an IP address
automatically from a DHCP server such as a router.
Select Static IP if you want to manually enter the IP
settings for the camera.
Click Next to continue.

4D-Link DCS-4705E Quick Installation Guide
4
ENGLISH
Take a moment to confirm your settings and click
Restart.
ViewingYour Camera via Web Browser
Click on the D-Link Setup Wizard SE icon that
was created in your Windows Start menu (Start >
D-Link > Setup Wizard SE).
Select the camera and click Link to access the web
configuration.
The Setup Wizard will automatically open your web
browser to the IP address of the camera.
This section displays your camera’s live video.You
can select your video profile and view or operate
the camera. For additional information about web
configuration, please refer to the user manual
included on the CD-ROM or the D-Link website.
Enter admin as the default username and leave the
password blank. Click OK to continue.

5
D-Link DCS-4705E Quick Installation Guide 5
ENGLISH
Mounting Instructions
It is highly recommended that you configure and test your camera before
mounting it.
If you need to waterproof your installation, please continue to the next page.
Place the mounting sticker where you want to
position the camera. Make sure the camera base
will be positioned so that the cable channel is on
the bottom.
Use a 6 mm drill bit to make the required holes
approximately 25 mm deep, then insert the wall
anchors into the holes.
If you are running the camera cables through
the wall, drill a hole in the center and pull the
cables through the hole.
Connect the power and Ethernet cables, or just the
Ethernet cable if you are using a PoE connection.
Use the screws provided to mount the camera to
the wall.
If you are running the camera cables out the
side of the camera, guide the camera cables
through the cable channel on the base.
To adjust the camera's angle, turn the adjustment
ring counterclockwise to loosen it, then move the
camera to the desired position and angle. When you
are finished, turn the adjustment ring clockwise to
tighten it.

6D-Link DCS-4705E Quick Installation Guide
6
ENGLISH
To waterproof your camera installation, follow the instructions below. Round
Ethernet cable, a crimping tool, and RJ-45 plugs are required for this
procedure.
Waterproofing Your Installation
Place the washer around the base of the Ethernet
connector as shown.
Connect the RJ-45 plug into the Ethernet
connector, then screw the waterproof connector
to the Ethernet connector by turning it about a
half-turn clockwise.
Thread bare Ethernet cable through the waterproof
connector as shown, then crimp an RJ-45 plug onto
the cable.

7
D-Link DCS-4705E Quick Installation Guide 7
ENGLISH
If you are using PoE to power your camera, use
the included rubber power connector plug to the
power connector.
If you are using a power adapter(not included)
to power your camera, wind waterproof tape
around the connection in an overlapping manner to
cover it.
Additional Information
Additional help and product information is available online at
http://www.dlink.com.
Warranty Information
Please visit http://warranty.dlink.com/ for warranty information for your region.
Screw the back part of the waterproof connector
clockwise until there is a tight seal around the
Ethernet cable.

36
8D-Link DCS-4705E Quick Installation Guide
РУССКИЙ
Краткое руководство по установке
Данное руководство содержит основные инструкции по установке камеры
DCS-4705E в сети. Для получения дополнительной информации по
настройке камеры, пожалуйста, обратитесь к руководству пользователя
на CD-диске из комплекта поставки или через Web-сайт D-Link.
Комплект поставки
Внешняя сетевая камера DCS-4705E
Водонепроницаемый коннектор для кабеля
Резиновая заглушка для разъема питания
Комплект для монтажа
CD-диск с руководством пользователя и программным
обеспечением
Краткое руководство по установке
Если что-либо из перечисленного отсутствует, обратитесь к поставщику.
Меры безопасности
Во избежание прекращения гарантии установку и обслуживание
должны проводить сертифицированные специалисты в соответствии с
региональными нормами и правилами.

37
9
D-Link DCS-4705E Quick Installation Guide
РУССКИЙ
Обзор аппаратной части
Объектив
камеры
Инфракрасная
подсветка
Используется для работы
камеры в ночное время
Кольцо для
регулировки
Ослабьте кольцо,
чтобы отрегулировать
положение камеры, а
затем затяните кольцо
для фиксации камеры в
требуемом положении
Кнопка Reset
Нажмите и удерживайте
кнопку Reset в течение
10 секунд, чтобы
сбросить настройки
камеры к заводским
Винт для заземления
Винтом заземления
можно прикрутить
клемму заземляющего
провода к камере
Разъем питания
Разъем для подключения 12 В / 1,5 А
адаптера питания (адаптер не входит
в комплект поставки)
Ethernet-разъем
Разъем RJ-45 для подключения
Ethernet-кабеля, а также для подачи
питания камеры по технологии Power
over Ethernet (PoE)