D-Link DCS-6517 User manual

DCS-6517
Quick Installation Guide
Краткое руководство по установке
Quick Installation Guide
5 Megapixel Day & Night Outdoor Dome Network Camera
This document will guide you through the
basic installation process for your new
D-Link Network Camera.

D-Link DCS-6517 Quick Install Guide
3
ENGLISH
DCS-6517 Quick Installation Guide
This installation guide provides basic instructions for installing the DCS-6517 Network
Camera on your network. For additional information about how to use the camera,
please see the User’s Manual which is available on the CD include in this package or
from the D-Link support website.
Installation Steps
1. Verify the package contents against the list below.
2. Hardware Overview
3. SD Card Installation
4. Assembly and Installation
5. Configuration with Wizar
6. Adjusting the lens 3-axis angle
1. Package Contents
° DCS-6517 Network Camera
° User Manual and Software on CD-ROM
° Power Adapter*
° Mounting Screws and Allen wrench
° Quick Installation Guide
° CAT5 Ethernet Cable
° Alignment Sticker
° Sunshield
° RJ-45 Extension connector
° Mounting Adapter
If any of the above items are missing, please contact your reseller.
*Depending on your region, a power adapter may not be included.

D-Link DCS-6517 Quick Install Guide
4
ENGLISH
2. Hardware Overview
Install the SD Card
Push the SD card into the camera with the
gold contacts oriented towards the base of
the camera. To eject the SD card, push the
SD card into the slot.
3. SD Card Installation
Disassemble the Camera
Open the camera enclosure by loosen the
4 screws. Lift the dome off the base of the
camera.
Power Connector
Connects to 12 V DC power
RJ-45 Extension connector
RJ-45 connector for Ethernet
which can also be used to power
the camera using Power over
Ethernet (PoE)
Reset Button
Resets camera to factory
default settings
Audio In
Connects to a microphone
DI/DO Wiring
I/O connectors for external
devices
Audio Out
Connects to speakers
Micro SD Slot

D-Link DCS-6517 Quick Install Guide
5
ENGLISH
4. Assembly and Installation
Mounting Installation
Please see the User Manual for detailed instructions regarding installation and mounting
of the camera using a mounting plate or bracket.
Attach the alignment sticker to the ceiling or wall.
Drill holes corresponding to the mounting template and
insert the plastic anchors in the holes.
Attach the cables to the corresponding cable
connectors.
Attach the dome up with the mounting template latch,
then push forward lock the latch. Using the bolt for
security lock the Camera.

D-Link DCS-6517 Quick Install Guide
6
ENGLISH
Pendant Mount (DCS-34-2)
Pendant
Bracket
Bracket
Cap
Rubber
Seal
Bracket
Cap
Mounting
Plate

D-Link DCS-6517 Quick Install Guide
7
ENGLISH
Bent Mount (DCS-34-3)
Bracket Cap
Bent
Bracket
Bracket
Cap
Mounting
Plate
Dome
Camera
Bent
Bracket

D-Link DCS-6517 Quick Install Guide
8
ENGLISH
Connection with a PoE Hub
If you are using a PoE hub, connect the IP camera to the hub via an Ethernet cable,
which will provide transmission of both power and data over a single cable.
General Connection Using 12 V DC Power Adapter
1. Connect the network camera to a hub via an Ethernet cable.
2. Connect the supplied power cable from the camera to a power outlet.

D-Link DCS-6517 Quick Install Guide
9
ENGLISH
5. Conguration with Wizard
Insert the DCS-6517 CD into your computer's CD-ROM drive to begin the installation. If
the Autorun function on your computer is disabled, or if the D-Link Launcher fails to start
automatically, click Start > Run. Type D:\autorun.exe, where D: represents the drive
letter of your CD-ROM drive.
After clicking Setup Wizard, the following window will open.
Click Next to continue.
Click Yes to accept the License Agreement.
Click Finish to complete the installation.
To start the installation process, click Next.
Note: The installation may take several minutes to
nish.

D-Link DCS-6517 Quick Install Guide
10
ENGLISH
Click on the D-Link Setup Wizard SE icon that was
created in your Windows Start menu.
Start > D-Link > Setup Wizard SE
Take a moment to conrm your settings and click Restart.
Select DHCP if your camera obtains an IP address
automatically when it boots up. Select static IP if the
camera will use the same IP address each time it is
started.
Click Next to proceed to the next page.
Enter the Admin ID and password. When logging in for
the rst time, the default Admin ID is admin with the
password left blank.
Click Next to proceed to the next page.
The Setup Wizard will appear and display the MAC
address and IP address of your camera(s). If you have
a DHCP server on your network, a valid IP Address
will be displayed. If your network does not use a
DHCP server, the network camera's default static IP
192.168.0.20 will be displayed.
Click the Wizard button to continue.

D-Link DCS-6517 Quick Install Guide
11
ENGLISH
DCS-6517
Click on the D-Link Setup Wizard SE icon that was
created in your Windows Start menu.
Start > D-Link > Setup Wizard SE
Viewing Camera via Web Browser
This section shows your camera’s live video. You
can select your video prole and view or operate
the camera. For additional information about web
conguration, please refer to the user manual
included on the CD-ROM or the D-Link website.
Enter admin as the default username and leave the
password blank. Click OK to continue.
Select the camera and click the button labeled
"Link" to access the web conguration.
The Setup Wizard will automatically open your web
browser to the IP address of the camera.
DCS-6517