D-Link DCS-935L User manual

DCS-935L
Quick Install Guide
HD Wi-Fi Camera

If any of the above items are missing, please contact your reseller.
Minimum Requirements
DCS-935L HD Wi-Fi Camera
Wall Mount Kit
Package Contents
• A wireless router (802.11ac/n/g) with Internet service
• An e-mail account (required to create a mydlink® account)
Network Device and Service
Power Adapter
• Wireless 802.11ac/n/g network
(Wireless AC network recommended for optimum performance)
Quick Install Guide
Mobile Device
• iPhone, iPad, or Android smartphone or tablet
(Refer to the mobile app’s store page to see if your device is compatible)
Quick Install Card
2

Product Overview
Back
Reset Button
MicroUSB Power
Connector Power LED
WPS LED
& Button
Direct LED
& Button
Front
Camera Lens
IR LEDs
Camera Stand
Microphone
Light Sensor
3
ENGLISH

Setting Up Your Camera
Please follow the instructions below to set up your mydlink camera.
Congratulations, your DCS-935L is now ready to use! Be sure to check the
support.dlink.com website periodically for the latest rmware updates to keep
your product up to date with the latest features.
Note: If you experience issues registering this camera with your mydlink account, or if you
purchased an open box or resold unit, perform a hard reset by pressing and holding the reset
button on the device for 10 seconds while the device is powered on. If you are returning the
device to the place of purchase, please perform the hard reset procedure to clear the
device of any personal data.
On your mobile device, download mydlink Home by going to
mydlinkhomeapp.dlink.com, or by searching for mydlink Home in the
iTunes App Store or Google Play.
1
3After logging in, tap the Settings icon in the top-left corner, select
Add New Device, and follow the instructions.
When you are asked to scan a QR code, use the code on the Quick Install
Card in your package, or on the label attached to your device.
Launch the mydlink Home app and create a new account or sign in to
your existing account.
2
iOS: If you are asked about allowing the app to
access your location, select Allow.
Android: Make sure location services are turned on
in your phone’s settings.
4

Mounting the Camera
Please refer to the steps below to assist you with mounting the camera.
We suggest that you congure the camera before mounting.
1. Use a pencil to mark two points on the wall or
ceiling that are 40 mm (1.6 in) apart. Use a 6 mm
drill bit to drill the holes where you marked.
The holes should be 25 mm deep (about 1 in
deep). Insert the screws into the holes. When
you tighten the screws, leave 2 mm for tting
the mounting base over the screw-heads.
1
2
2. Place the mounting base over the screws that
are inserted in the wall or ceiling. Make sure to
t the screw-heads over the big holes in the
base, and slide the mounting base downward
to lock it rmly in place. Lightly pull the base
forward to make sure that it is locked. Adjust
the angle of the camera as needed.
Note: If the wall is made out of concrete, before inserting the screws, insert
the provided plastic anchors to support the screws.
5
ENGLISH

1. What is a mydlink No.? What is it used for?
Each camera has a unique eight-digit mydlink No. which will be shown on the
label on the back of your camera. This eight-digit number identies your device,
and is required to add your device to your mydlink account.
2. What can I do if my camera is not working correctly?
• To make sure your hardware is installed correctly, check to see if:
- the power LED is lit solid green
- your Internet connection is working
- your router’s wireless & WAN connections are okay
- your router supports UPnP®
- your mobile device is currently on the same wireless network as your camera
- both your mobile device and camera have a working Internet connection
• If your camera is still not working, check your router and make sure it has the
latest rmware.
3. What can I do if I forget my password?
If you forget your password, you must reset the
camera. Unfortunately, this process will change
your settings back to factory default and remove
it from your account. To reset the camera, locate
the reset button on the back of the camera. With
the camera powered on, use an unfolded paper
clip to hold the button down for 10 seconds. Once
the camera restarts, follow the steps in this guide
to set up your camera again.
4. Why is there a white haze when viewing in night vision mode?
When viewing in night vision mode, the IR lights on the camera may be reecting
o a nearby surface. Try repositioning the camera in order to avoid glare from
IR LEDs.
5. Can I use my DCS-935L as a portable camera?
Yes, to use the DCS-935L as a portable camera, you can power the camera with
a portable battery that supplies 5V/2A of power.
FAQs
Reset
Button
6

Technical Support
This guide is only for initial conguration. Please refer to the user manual to learn
more or visit http://www.mydlink.com for more information. Also feel free to
contact us. U.S. and Canadian customers can contact D-Link Technical Support
through our website.
http://support.dlink.com
USA
Ver. 1.02(NA)_90x130
March 20, 2015
29072600935LA17
©2015 D-Link. All Rights Reserved. D-Link and the D-Link logo are trademarks or registered trademarks of D-Link. All
other third party marks mentioned herein may be trademarks of their respective owners. Maximum wireless signal rate
derived from IEEE Standard 802.11ac, 802.11g, and 802.11n specications. Actual data throughput will vary. Network
conditions and environmental factors, including volume of network trac, building materials and construction, and
network overhead, lower actual data throughput rate. Environmental conditions will adversely aect wireless signal
range. Product specications, size and shape are subject to change without notice, and actual product appearance may
dier from that depicted on the packaging. This publication may not be reproduced, in whole or in part, without prior
express written permission from D-Link Systems, Inc.
Canada
http://support.dlink.ca