D-Link DGS-510 User manual

1

DGS-1510 Series Gigabit Ethernet SmartPro Switch CLI Reference Guide
ii
Table of Contents
1. Introduction.............................................................................................................................................................1
2. Basic CLI Commands...........................................................................................................................................10
3. 802.1X Commands...............................................................................................................................................24
4. Access Control List (ACL) Commands.................................................................................................................37
5. Access Management Commands ........................................................................................................................65
6. ARP Spoofing Prevention Commands.................................................................................................................84
7. Asymmetric VLAN Commands.............................................................................................................................86
8. Authentication, Authorization, and Accounting (AAA) Commands ......................................................................87
9. Basic IPv4 Commands.......................................................................................................................................110
10. Basic IPv6 Commands.......................................................................................................................................117
11. BPDU Attack Protection Commands..................................................................................................................130
12. Cable Diagnostics Commands...........................................................................................................................134
13. Command Logging Commands .........................................................................................................................137
14. Debug Commands .............................................................................................................................................138
15. DHCP Auto-Configuration Commands...............................................................................................................151
16. DHCP Client Commands....................................................................................................................................153
17. DHCP Relay Commands....................................................................................................................................156
18. DHCP Snooping Commands .............................................................................................................................176
19. DHCPv6 Client Commands................................................................................................................................194
20. DHCPv6 Guard Commands...............................................................................................................................196
21. DHCPv6 Relay Commands................................................................................................................................200
22. Digital Diagnostics Monitoring (DDM) Commands.............................................................................................205
23. D-Link Discovery Protocol (DDP) Client Commands.........................................................................................214
24. Domain Name System (DNS) Commands.........................................................................................................217
25. DoS Prevention Commands...............................................................................................................................222
26. Dynamic ARP Inspection Commands................................................................................................................226
27. Error Recovery Commands................................................................................................................................239
28. Ethernet Ring Protection Switching (ERPS) Commands...................................................................................242
29. File System Commands.....................................................................................................................................255
30. Filter Database (FDB) Commands.....................................................................................................................261
31. GARP VLAN Registration Protocol (GVRP) Commands...................................................................................274
32. Gratuitous ARP Commands...............................................................................................................................282
33. IGMP Snooping Commands ..............................................................................................................................285
34. Interface Commands..........................................................................................................................................300
35. IP Source Guard Commands.............................................................................................................................319
36. IP Utility Commands...........................................................................................................................................325
37. IP-MAC-Port Binding (IMPB) Commands..........................................................................................................332
38. IPv6 Snooping Commands.................................................................................................................................336
39. IPv6 Source Guard Commands .........................................................................................................................341
40. Japanese Web-based Access Control (JWAC) Commands..............................................................................346
41. Jumbo Frame Commands..................................................................................................................................357

DGS-1510 Series Gigabit Ethernet SmartPro Switch CLI Reference Guide
iii
42. Link Aggregation Control Protocol (LACP) Commands.....................................................................................358
43. Link Layer Discovery Protocol (LLDP) Commands............................................................................................364
44. Loopback Detection (LBD) Commands..............................................................................................................393
45. MAC Authentication Commands........................................................................................................................400
46. Mirror Commands...............................................................................................................................................404
47. MLD Snooping Commands................................................................................................................................408
48. Multiple Spanning Tree Protocol (MSTP) Commands.......................................................................................423
49. Neighbor Discovery (ND) Inspection Commands ..............................................................................................432
50. Network Access Authentication Commands......................................................................................................436
51. Network Time Protocol (NTP) Commands.........................................................................................................449
52. Port Security Commands ...................................................................................................................................463
53. Power over Ethernet (PoE) Commands.............................................................................................................469
54. Power Saving Commands..................................................................................................................................485
55.Protocol Independent Commands......................................................................................................................491
56. Quality of Service (QoS) Commands.................................................................................................................497
57. Remote Network MONitoring (RMON) Commands ...........................................................................................530
58. Router Advertisement (RA) Guard Commands..................................................................................................537
59. Safeguard Engine Commands...........................................................................................................................541
60. Secure Shell (SSH) Commands.........................................................................................................................548
61. Secure Sockets Layer (SSL) Commands ..........................................................................................................555
62. sFlow Commands...............................................................................................................................................563
63. Simple Network Management Protocol (SNMP) Commands ............................................................................569
64. Single IP Management (SIM) Commands..........................................................................................................589
65. Spanning Tree Protocol (STP) Commands........................................................................................................600
66. Stacking Commands..........................................................................................................................................613
67. Storm Control Commands..................................................................................................................................618
68. Surveillance VLAN Commands..........................................................................................................................623
69. Switch Port Commands......................................................................................................................................634
70. System File Management Commands...............................................................................................................639
71. System Log Commands.....................................................................................................................................650
72. Time and SNTP Commands ..............................................................................................................................658
73. Time Range Commands ....................................................................................................................................664
74. Traffic Segmentation Commands.......................................................................................................................667
75. Virtual LAN (VLAN) Commands.........................................................................................................................669
76. Voice VLAN Commands.....................................................................................................................................682
77. Web Authentication Commands.........................................................................................................................689
Appendix A - System Log Entries .................................................................................................................................694
Appendix B - Trap Entries.............................................................................................................................................720
Appendix C - RADIUS Attributes Assignment...............................................................................................................731
Appendix D - IETF RADIUS Attributes Support............................................................................................................734
Appendix E - ERPS Information....................................................................................................................................736

DGS-1510 Series Gigabit Ethernet SmartPro Switch CLI Reference Guide
1
1. Introduction
This manual’s command descriptions are based on the software release 1.40. The commands listed
here are the subset of commands that are supported by the DGS-1510 Series SmartPro Switch.
Audience
This CLI Reference Guide is intended for network administrators and other IT networking
professionals responsible for managing the switch by using the Command Line Interface (CLI). The
CLI is the primary management interface to the DGS-1510 Series SmartPro Switch, which will be
generally be referred to simply as “the Switch” within this manual. This manual is written in a way that
assumes that you already have the experience and knowledge of Ethernet and modern networking
principles for Local Area Networks.
Other Documentation
The documents below are a further source of information in regards to configuring and
troubleshooting the Switch. All the documents are available from the CD bundled with this switch, or
from the D-Link website. Other documents related to the Switch are:
DGS-1510 Series Gigabit Ethernet SmartPro Switch Hardware Installation Guide
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide
Conventions
Convention Description
Boldface Font Commands, command options and keywords are printed in
boldface. Keywords, in the command line, are to be entered exactly
as they are displayed.
UPPERCASE ITALICS Font Parameters or values that must be specified are printed in
UPPERCASE ITALICS. Parameters in the command line are to be
replaced with the actual values that are desired to be used with the
command.
Square Brackets [ ] Square brackets enclose an optional value or set of optional
arguments.
Braces { } Braces enclose alternative keywords separated by vertical bars.
Generally, one of the keywords in the separated list can be chosen.
Vertical Bar | Optional values or arguments are enclosed in square brackets and
separated by vertical bars. Generally, one or more of the vales or
arguments in the separated list can be chosen.
Blue Courier Font This convention is used to represent an example of a screen
console display including example entries of CLI command input
with the corresponding output.
Notes, Notices, and Cautions
Below are examples of the three types of indicators used in this manual. When administering your
switch using the information in this document, you should pay special attention to these indicators.
Each example below provides an explanatory remark regarding each type of indicator.
NOTE: A note indicates important information that helps you make better use of your
device.

DGS-1510 Series Gigabit Ethernet SmartPro Switch CLI Reference Guide
2
NOTICE: A notice indicates either potential damage to hardware or loss of data and tells
you how to avoid the problem.
CAUTION: A caution indicates a potential for property damage, personal injury, or death.
Command Descriptions
The information pertaining to each command in this reference guide is presented using a number of
template fields. The fields are:
Description - This is a short and concise statement describing the commands functionality.
Syntax - The precise form to use when entering and issuing the command.
Parameters - A table where each row describes the optional or required parameters, and their
use, that can be issued with the command.
Default - If the command sets a configuration value or administrative state of the Switch then
any default settings (i.e. without issuing the command) of the configuration is shown here.
Command Mode - The mode in which the command can be issued. These modes are
described in the section titled “Command Modes” below.
Command Default Level – The user privilege level in which the command can be issued.
Usage Guideline - If necessary, a detailed description of the command and its various
utilization scenarios is given here.
Example(s) - Each command is accompanied by a practical example of the command being
issued in a suitable scenario.
Command Modes
There are several command modes available in the command-line interface (CLI). The set of
commands available to the user depends on both the mode the user is currently in and their privilege
level. For each case, the user can see all the commands that are available in a particular command
mode by entering a question mark (?) at the system prompt.
The command-line interface has three pre-defined privilege levels:
Basic User - Privilege Level 1. This user account level has the lowest priority of the user
accounts. The purpose of this type of user account level is for basic system checking.
Operator - Privilege Level 12. This user account level is used to grant system configuration
rights for users who need to change or monitor system configuration, except for security related
information such as user accounts and SNMP account settings, etc.
Administrator - Privilege Level 15. This administrator user account level can monitor all
system information and change any of the system configuration settings expressed in this
configuration guide.
The command-line interface has a number of command modes. There are three basic command
modes:
User EXEC Mode
Privileged EXEC Mode
Global Configuration Mode
All other sub-configuration modes can be accessed via the Global Configuration Mode.
When a user logs in to the Switch, the privilege level of the user determines the command mode the
user will enter after initially logging in. The user will either log into User EXEC Mode or the Privileged
EXEC Mode.
Users with a basic user level will log into the Switch in the User EXEC Mode.
Users with operator or administrator level accounts will log into the Switch in the Privileged
EXEC Mode.

DGS-1510 Series Gigabit Ethernet SmartPro Switch CLI Reference Guide
3
Therefore, the User EXEC Mode can operate at a basic user level and the Privileged EXEC Mode can
operate at the operator, or administrator levels. The user can only enter the Global Configuration
Mode from the Privileged EXEC Mode. The Global Configuration Mode can be accessed by users
who have operator or administrator level user accounts.
As for sub-configuration modes, a subset of those can only be accessed by users who have the
highest secure administrator level privileges.
The following table briefly lists the available command modes. Only the basic command modes and
some of the sub-configuration modes are enumerated. The basic command modes and basic sub-
configuration modes are further described in the following chapters. Descriptions for the rest of the
sub-configuration modes are not provided in this section. For more information on the additional sub-
configuration modes, the user should refer to the chapters relating to these functions.
The available command modes and privilege levels are described below:
Command Mode /
Privilege Level Purpose
User EXEC Mode /
Basic User level This level has the lowest priority of the user accounts. It is provided
only to check basic system settings.
Privileged EXEC Mode /
Operator level For changing both local and global terminal settings, monitoring, and
performing certain system administration tasks. The system
administration tasks that can be performed at this level except for any
security related information.
Privileged EXEC Mode /
Administrator level This level is identical to privileged EXEC mode at the operator level,
except that a user at the administrator level can monitor and clear
security related settings.
Global Configuration Mode /
Operator level For applying global settings, except for security related settings, on
the entire switch. In addition to applying global settings on the entire
switch, the user can access other sub-configuration modes from
global configuration mode.
Global Configuration Mode /
Administrator level For applying global settings on the entire switch. In addition to
applying global settings on the entire switch, the user can access
other sub-configuration modes from global configuration mode.
Interface Configuration Mode
/ Administrator level For applying interface related settings.
VLAN Interface Configuration
Mode For applying VLAN interface related settings.
User EXEC Mode at Basic User Level
This command mode is mainly designed for checking basic system settings. This command mode can
be entered by logging in as a basic user.
Privileged EXEC Mode at Operator Level
Users logged into the Switch in privileged EXEC mode at this level can change both local and global
terminal settings, monitor, and perform system administration tasks (except for security related
information). The method to enter privileged EXEC mode at operator level is to login to the Switch
with a user account that has a privilege level of 12.

DGS-1510 Series Gigabit Ethernet SmartPro Switch CLI Reference Guide
4
Privileged EXEC Mode at Administrator Level
This command mode has a privilege level of 15. Users logged in with this command mode can
monitor all system information and change any system configuration settings mentioned in this
Configuration Guide. The method to enter privileged EXEC mode at administrator level is to login to
the Switch with a user account that has a privilege level of 15.
Global Configuration Mode
The primary purpose of the global configuration mode is to apply global settings on the entire switch.
Global configuration mode can be accessed at operator or administrator level user accounts. However,
security related settings are not accessible at operator user account. In addition to applying global
settings on the entire switch, the user can also access other sub-configuration modes. In order to
access the global configuration mode, the user must be logged in with the corresponding account
level and use the configure terminal command in the privileged EXEC mode.
In the following example, the user is logged in as an Administrator in the Privileged EXEC Mode and
uses the configure terminal command to access the Global Configuration Mode:
Switch# configure terminal
Switch(config)#
The exit command is used to exit the global configuration mode and return to the privileged EXEC
mode.
Switch(config)# exit
Switch#
The procedures to enter the different sub-configuration modes can be found in the related chapters in
this Configuration Guide. The command modes are used to configure the individual functions.
Interface Configuration Mode
Interface configuration mode is used to configure the parameters for an interface or a range of
interfaces. An interface can be a physical port, VLAN, or other virtual interface. Thus, interface
configuration mode is distinguished further according to the type of interface. The command prompt
for each type of interface is slightly different.
VLAN Interface Configuration Mode
VLAN interface configuration mode is one of the available interface modes and is used to configure
the parameters of a VLAN interface.
To access VLAN interface configuration mode, use the following command in global configuration
mode:
Switch(config)# interface vlan 1
Switch(config-if)#
Creating a User Account
You can create different user account for various levels. This section will assist a user with creating a
user account by means of the Command Line Interface.
NOTE: By default, one user account is already configured on the Switch. Both the
username and password for this account is admin, and the privilege level is 15.

DGS-1510 Series Gigabit Ethernet SmartPro Switch CLI Reference Guide
5
NOTE: After upgrading the firmware on the Switch and no user accounts were created,
the default admin user account will automatically be created after rebooting the
Switch with the new boot-up configuration file.
NOTE: After upgrading the firmware on the Switch and user accounts were created, the
default admin user account will not be created automatically. Only after a factory
reset was performed on the Switch will the default admin user account be
created.
Observe the following example.
Switch>enable
Switch#configure terminal
Switch(config)#username user1 password pass1234
Switch(config)#username user1 privilege 15
Switch(config)#line console
Switch(config-line)#login local
Switch(config-line)#
In the above example we had to navigate and access the username command.
Starting in the User EXEC Mode we enter the command enable to access the Privileged EXEC
Mode.
After accessing the Privileged EXEC Mode, we entered the command configure terminal to
access the Global Configuration Mode. The username command can be used in the Global
Configuration Mode.
The command username user1 password pass1234 creates a user account with the
username of user1 and a password of pass1234.
The command username user1 privilege 15 assigns a privilege level value of 15 to the user
account admin.
The command line console allows us to access the console interface’s Line Configuration
Mode.
The command login local tell the Switch that users need to enter locally configured login
credentials to access the console interface.
Save the running configuration to the start-up configuration. This means to save the changes made so
that when the Switch is rebooted, the configuration will not be lost. The following example shows how
to save the running configuration to the start-up configuration.
Switch#copy running-config startup-config
Destination filename startup-config? [y/n]: y
Saving all configurations to NV-RAM.......... Done.
Switch#

DGS-1510 Series Gigabit Ethernet SmartPro Switch CLI Reference Guide
6
After the Switch was rebooted, or when the users logs out and back in, the newly created username
and password must be entered to access the CLI interface again, as seen below.
DGS-1510-28XMP Gigabit Ethernet SmartPro Switch
Command Line Interface
Firmware: Build 1.40.014
Copyright(C) 2017 D-Link Corporation. All rights reserved.
User Access Verification
Username:user1
Password: ********
Switch#
Interface Notation
When configuration the physical ports available on this switch, a specific interface notation is used.
The following will explain the layout, terminology and use of this notation.
In the following example, we will enter the Global Configuration Mode and then enter the Interface
Configuration Mode, using the notation 1/0/1. After entering the Interface Configuration Mode for port
1, we will change the speed to 1 Gbps, using the speed 1000 command.
Switch# configure terminal
Switch(config)# interface Ethernet 1/0/1
Switch(config-if)# speed 1000
Switch(config-if)#
In the above example the notation 1/0/1 was used. The terminology for each parameter is as follows:
Interface Unit’s ID / Open Slot’s ID / Port’s ID
The Interface Unit’s ID is the ID of the stacking unit without the physical stack. If stacking is disabled
or this unit is a stand-alone unit, then this parameter is irrelevant. The Open Slot’s ID is the ID of the
module plugged into the open module slot of the Switch. The DGS-1510 Series does not support any
open modules slots, thus this parameters will always by zero for this switch series. Lastly, the Port’s
ID is the physical port number of the port being configured.
In summary the above example will configure the stacked switch with the ID of 1, with the open slot ID
of 0, and the physical port number 1.
Error Messages
When the users issue a command that the Switch does not recognize, error messages will be
generated to assist users with basic information about the mistake that was made.
A list of possible error messages are found in the table below.
Error Message Meaning
Ambiguous command Not enough keywords were entered for the Switch to recognize the
command.
Incomplete command The command was not entered with all the required keyword.

DGS-1510 Series Gigabit Ethernet SmartPro Switch CLI Reference Guide
7
Invalid input detected at
^marker The command was entered incorrectly.
The following example shows how an ambiguous command error message is generated.
Switch# show v
Ambiguous command
Switch#
The following example shows how an incomplete command error message is generated.
Switch# show
Incomplete command
Switch#
The following example shows how an invalid input error message is generated.
Switch# show verb
^
Invalid input detected at ^marker
Switch#
Editing Features
The command line interface of this switch supports to following keyboard keystroke editing features.
Keystroke Description
Delete Deletes the character under the cursor and shifts the remainder of
the line to the left.
Backspace Deletes the character to the left of the cursor and shifts the
remainder of the line to the left.
Left Arrow Moves the cursor to the left.
Right Arrow Moves the cursor to the right.
CTRL+R Toggles the insert text function on and off. When on, text can be
inserted in the line and the remainder of the text will be shifted to
the right. When off, text can be inserted in the line and old text will
automatically be replaced with the new text.
Return Scrolls down to display the next line or used to issue a command.
Space Scrolls down to display the next page.
ESC Escapes from the displaying page.
Display Result Output Modifiers
Results displayed by show commands can be filtered using the following parameters:
begin FILTER-STRING - This parameter is used to start the display with the first line that
matches the filter string.
include FILTER-STRING - This parameter is used to display all the lines that match the filter
string.
exclude FILTER-STRING - This parameter is used to exclude the lines that match the filter
string from the display.

DGS-1510 Series Gigabit Ethernet SmartPro Switch CLI Reference Guide
8
The example below shows how to use the begin FILTER-STRING parameter in a show command.
Switch#show running-config | begin # AAA
# AAA
configure terminal
# AAA START
no aaa new-model
# AAA END
end
# PRIVMGMT
configure terminal
# COMMAND LEVEL START
# COMMAND LEVEL END
# LEVEL START
# LEVEL END
# ACCOUNT START
# ACCOUNT END
# LOGIN START
# LOGIN END
end
# CLI
# BASIC
CTRL+C ESC q Quit SPACE n Next Page ENTER Next Entry a All
The example below shows how to use the include FILTER-STRING parameter in a show command.
Switch#show running-config | include # DEVICE
# DEVICE
Switch#

DGS-1510 Series Gigabit Ethernet SmartPro Switch CLI Reference Guide
9
The example below shows how to use the exclude FILTER-STRING parameter in a show command.
Switch#show running-config | exclude # DEVICE
Building configuration...
Current configuration : 30764 bytes
#-------------------------------------------------------------------------------
# DGS-1510-28XMP Gigabit Ethernet SmartPro Switch
# Configuration
#
# Firmware: Build 1.40.014
# Copyright(C) 2017 D-Link Corporation. All rights reserved.
#-------------------------------------------------------------------------------
# STACK
end
end
configure terminal
end
# SSL
CTRL+C ESC q Quit SPACE n Next Page ENTER Next Entry a All

DGS-1510 Series Gigabit Ethernet SmartPro Switch CLI Reference Guide
10
2. Basic CLI Commands
2-1 help
This command is used to display a brief description of the help system. Use the help command in any
command mode.
help
Parameters
None.
Default
None.
Command Mode
EXEC Mode or Any Configuration Mode.
Command Default Level
Level: 1.
Usage Guideline
The help command provides a brief description for the help system, which includes the following
functions:
To list all commands available for a particular command mode, enter a question mark (?) at the
system prompt.
To obtain a list of commands that begin with a particular character string, enter the abbreviated
command entry immediately followed by a question mark (?). This form of help is called word
help, because it lists only the keywords or arguments that begin with the abbreviation entered.
To list the keywords and arguments associated with a command, enter a question mark (?) in
place of a keyword or argument on the command line. This form of help is called the command
syntax help, because it lists the keywords or arguments that apply based on the command,
keywords, and arguments already entered.
Example
This example shows how the help command is used to display a brief description of the help system.
Switch#help
The switch CLI provides advanced help feature.
1. Help is available when you are ready to enter a command
argument (e.g. 'show ?') and want to know each possible
available options.
2. Help is provided when an abbreviated argument is entered
and you want to know what arguments match the input(e.g. 'show ve?'.).
If nothing matches, the help list will be empty and you must backup
until entering a '?' shows the available options.
3. For completing a partial command name could enter the abbreviated
command name immediately followed by a <Tab> key.
Note:
Since the character '?' is used for help purpose, to enter
the character '?' in a string argument, press ctrl+v immediately
followed by the character '?'.
Switch#

DGS-1510 Series Gigabit Ethernet SmartPro Switch CLI Reference Guide
11
The following example shows how to use the word help to display all the Privileged EXEC Mode
commands that begin with the letters “re”. The letters entered before the question mark (?) are
reprinted on the next command line to allow the user to continue entering the command.
Switch#re?
reset renew rename reboot
Switch#re
The following example shows how to use the command syntax help to display the next argument of
a partially complete telnet command. The characters entered before the question mark (?) is
reprinted on the next command line to allow the user to continue entering the command.
Switch#telnet ?
A.B.C.D IP address of a remote system
WORD Telnet destination hostname
X:X:X:X::X IPv6 address of a remote system
Switch#telnet
2-2 enable
This command is used to enter the Privileged EXEC Mode.
enable [PRIVILEGE-LEVEL]
Parameters
PRIVILEGE-LEVEL (Optional) Specifies to set the privilege level for the user. The
privilege level is between 1 and 15. If not specified, level 15 will be
used.
Default
None.
Command Mode
User EXEC Mode.
Privilege EXEC Mode.
Command Default Level
Level: 1.
Usage Guideline
Execute this command if the current level is lower than the command level. If the privileged level
requires a password, enter it in the field provided. However, only three attempts are allowed. Failure
to access this level returns the user to the current level.
Example
This example shows how to enter the Privileged EXEC Mode.
Switch# enable 15
password:***
Switch#

DGS-1510 Series Gigabit Ethernet SmartPro Switch CLI Reference Guide
12
2-3 disable
This command is used to downgrade to a level lower user level than the privileged level.
disable [PRIVILEGE-LEVEL]
Parameters
PRIVILEGE LEVEL Specifies the privilege level to enter. If not specified, level 1 is used.
Default
None.
Command Mode
User EXEC Mode.
Privilege EXEC Mode.
Command Default Level
Level: 1.
Usage Guideline
Use this command to enter the privilege level, which is lower than the current level. When using this
command to enter the privilege level, that has a password configured, no password is needed.
Example
This example shows how to logout.
Switch# disable
Switch> logout
2-4 configure terminal
This command is used to enter the Global Configuration Mode.
configure terminal
Parameters
None.
Default
None
Command Mode
Privilege EXEC Mode.
Command Default Level
Level: 12.
Usage Guideline
This command is used to enter the Global Configuration Mode.
Example
This example shows how to enter into Global Configuration Mode.

DGS-1510 Series Gigabit Ethernet SmartPro Switch CLI Reference Guide
13
Switch# configure terminal
Switch(config)#
2-5 login (EXEC)
This command is used to configure a login username.
login
Parameters
None.
Default
None.
Command Mode
User EXEC Mode.
Privileged EXEC Mode.
Command Default Level
Level: 1.
Usage Guideline
Use this command to change the login account. Three attempts are allowed to login to the Switch’s
interface. When using Telnet, if all attempts fail, access will return to the command prompt. If no
information is entered within 60 seconds, the session will return to the state when logged out.
Example
This example shows how to login with username “user1”.
Switch# login
Username: user1
Password: xxxxx
Switch#
2-6 login (Line)
This command is used to set the line login method. Use the no form of this command to disable the
login.
login [local]
no login
Parameters
login Specifies that the line login method will be login.
local Specifies that the line login method will be local.

DGS-1510 Series Gigabit Ethernet SmartPro Switch CLI Reference Guide
14
Default
By default, all line interfaces use the login local method (by username and password).
Command Mode
Line Configuration Mode.
Command Default Level
Level: 15.
Usage Guideline
For Console and Telnet access, when AAA is enabled, the line uses rules configured by the AAA
module. When AAA is disabled, the line uses the following authentication rules:
When login is disabled, the user can enter the line at Level 1.
When the by password option is selected, after inputting the same password as the command
password, the user enter the line at level 1. If the password wasn’t previously configured an
error message will be displayed and the session will be closed.
When the username and password option is selected, enter the username and password
configured by the username command.
For SSH access, there are three authentication types:
SSH public key,
Host-based authentication, and
Password authentication.
The SSH public key and host-based authentication types are independent from the login command in
the line mode. If the authentication type is password, the following rules apply:
When AAA is enabled, the AAA module is used.
When AAA is disabled, the following rules are used:
○When login is disabled, the username and password is ignored. Enter the details at Level
1.
○When the username and password option is selected, use the username and password
setup by the username command.
○When the password option is selected, the username is ignored but a password is
required using the password command to enter the line at level 1.
Example
This example shows how to enter the Line Configuration Mode and to create a password for the line
user. This password only takes effect once the corresponding line is set to login.
Switch# configure terminal
Switch(config)# line console
Switch(config-line)# password loginpassword
Switch(config-line)#
This example shows how to configure the line console login method as “login”.
Switch# configure terminal
Switch(config)# line console
Switch(config-line)# login
Switch(config-line)#
This example shows how to enter the login command. The device will check the validity of the user
from the password create command. If correct, the user will have access at the particular level.
Switch#login
Password:*************
Switch#

DGS-1510 Series Gigabit Ethernet SmartPro Switch CLI Reference Guide
15
This example shows how to create a username “useraccount” with the password of “pass123” and
use Privilege 12.
Switch# configure terminal
Switch(config)# username useraccount privilege 12 password 0 pass123
Switch(config)#
This example shows how to configure the login method as login local.
Switch# configure terminal
Switch(config)# line console
Switch(config-line)# login local
Switch(config-line)#
2-7 logout
This command is used to close an active terminal session by logging off the Switch.
logout
Parameters
None.
Default
None.
Command Mode
User EXEC Mode.
Privilege EXEC Mode.
Command Default Level
Level:1.
Usage Guideline
Use this command to close an active terminal session by logging out of the device.
Example
This example shows how to logout
Switch# disable
Switch# logout
2-8 end
This command is used to end the current configuration mode and return to the highest mode in the
CLI mode hierarchy which is either the User EXEC Mode or the Privileged EXEC Mode.
end
Parameters
None.

DGS-1510 Series Gigabit Ethernet SmartPro Switch CLI Reference Guide
16
Default
None.
Command Mode
EXEC Mode or Any Configuration Mode.
Command Default Level
Level: 1.
Usage Guideline
Executing this command will return access to the highest mode in the CLI hierarchy regardless of
what configuration mode or configuration sub-mode currently located at.
Example
This example shows how to end the Interface Configuration Mode and go back to the Privileged
EXEC Mode.
Switch# configure terminal
Switch(config)# interface eth1/0/1
Switch(config-if)#end
Switch#
2-9 exit
This command is used to end the configuration mode and go back to the last mode. If the current
mode is the User EXEC Mode or the Privilege EXEC Mode, executing the exit command logs you out
of the current session.
exit
Parameters
None.
Default
None.
Command Mode
EXEC Mode or Any Configuration Mode.
Command Default Level
Level: 1.
Usage Guideline
Use this command to exit the current configuration mode and go back to the last mode. When the
user is in the User EXEC Mode or the Privilege EXEC Mode, this command will logout the session.
Example
This example shows how to exit from the Interface Configuration Mode and return to the Global
Configuration Mode.
Switch# configure terminal
Switch(config) interface eth1/0/1
Switch(config-if)#exit
Switch(config)#

DGS-1510 Series Gigabit Ethernet SmartPro Switch CLI Reference Guide
17
2-10 show history
This command is used to list the commands entered in the current EXEC Mode session.
show history
Parameters
None.
Default
None.
Command Mode
EXEC Mode or Any Configuration Mode.
Command Default Level
Level: 1.
Usage Guideline
Commands entered are recorded by the system. A recorded command can be recalled by pressing
CTRL+P or the Up Arrow key which will recall previous commands in sequence. The history buffer
size is fixed at 20 commands.
The function key instructions, below, displays how to navigate the command in the history buffer.
CTRL+P or the Up Arrow key - Recalls commands in the history buffer, beginning with the most
recent command. Repeat the key sequence to recall successively older commands.
CTRL+N or the Down Arrow key - Returns to more recent commands in the history buffer after
recalling commands with Ctrl-P or the Up Arrow key. Repeat the key sequence to recall
successively more recent commands.
Example
This example shows how to display the command buffer history.
Switch# show history
help
history
Switch#
2-11 show environment
This command is used to display fan, temperature, power availability and status information.
show environment [fan | power | temperature]
Parameters
fan (Optional) Specifies to display the Switch fan detailed status.
power (Optional) Specifies to display the Switch power detailed status.
temperature (Optional) Specifies to display the Switch temperature detailed
status.
Default
None.