D-Link DIS-F100G Series User manual

DIS-F100G SERIES
Gigabit Industrial PoE Switches
with Long Reach PoE Ports
Getting Started Guide for
Industrial Ethernet Switch
This document will guide you through the basic installation process
for your new D-Link Industrial Ethernet Switch.
QUICK INSTALLATION GUIDE
Documentation is also available on the D-Link website, see dlink.com.au

QUICK INSTALLATION GUIDE | DIS-F100G SERIES 2
Before You Begin
This Quick Installation Guide gives you step-by-step instructions for setting up the
DIS-F100G Series Gigabit Industrial PoE Switch. The model you have purchased may appear
slightly dierent from the one shown in the illustrations. For more detailed information
about the Switch, please refer to the user manual.
Package Contents
This package should include the following items:
• DIS-F100G Series Switch
• Terminal block
• DIN rail mounts (installed)
• Quick Installation Guide
If any of the above items are damaged or missing, please contact your local D-Link Reseller.
LED Indicators
HARDWARE OVERVIEW
LED Status Description
P1, P2 On The corresponding power source is connected
O The corresponding power source is not connected or failed
F1, F2 On or Flashing SFP port connected and active
O SFP port not connected

QUICK INSTALLATION GUIDE | DIS-F100G SERIES 3
Mounting the Switch on a DIN Rail
Before beginning either mounting or removing the DIS-F100G from a DIN rail, please
ensure that the DIN rail is level and that the DIN rail mounting kit is installed correctly on
the DIS-F100G. Use the following instructions to install the DIS-F100G on a DIN rail:
1. With the back of the DIS-F100G facing the DIN rail, lower the top part of the rail
mounting kit onto the DIN rail.
2. Push the DIS-F100G vertically down and rotate the bottom of the DIS-F100G towards
the DIN rail, to attach the Switch to the DIN rail.
Use the following instructions to remove the DIS-F100G from a DIN rail:
1. Push the DIS-F100G vertically down to create enough space at the bottom of the rail
mounting kit to remove the DIS-F100G from the DIN rail.
2. Rotate the DIS-F100G upwards to remove the bottom of the rail mounting kit from the
rail, and lift the DIS-F100G upwards to remove the whole of the Switch from the DIN rail.
Grounding the Switch
To use the DIS-F100G safely, it needs to be grounded. Connect a grounding wire to the
grounding connector on the Switch and use a Phillips head screwdriver to secure the wire.
Attach the other end of the grounding cable to an appropriate grounding source.
Grounding Wire
Before You Begin
Observe the following precautions to help prevent shutdowns, equipment failures, and
personal injury:
• Install the DIS-F100G in a cool and dry place. Refer to the technical specications in the
user manual for the acceptable operating temperature and humidity ranges.
• Leave at least 10 cm of space at the top, rear and bottom of the Switch for ventilation.
• Visually inspect the power connector and make sure that it is fully secured to the
power cord.
• Do not stack any devices on top of the Switch.
It is also recommended that power and grounding requirements are investigated before
mounting the Switch.
HARDWARE INSTALLATION

QUICK INSTALLATION GUIDE | DIS-F100G SERIES 4
Using the Terminal Connections
Before proceeding, ensure that all power sources have been disconnected from the
DIS-F100G, and that the power source you are wiring to the DIS-F100G is also disconnected.
Use the following instructions to power the DIS-F100G using the terminal connections:
1. Before continuing, consult the diagram above to decide which wires from the power
source need to connect to which contacts on the terminal block. Note that two power
sources can be used; one inserted into P1+ / P1- and the other inserted into P2+ / P2-.
If you only wish to use one power source, insert the wires into P1+ / P1-.
2. Using a at head screwdriver, loosen the connections in the terminal block by un-screwing
the terminal connections that you wish to use.
3. Insert the wires into the terminal connections and use the screwdriver to tighten the
screws to secure the wires.
4. Re-insert the terminal block into the terminal block socket on the DIS-F100G.
Connecting to a Power Source
The DIS-F100G can be powered using the in-built terminal connector. This allows dual power
inputs, using wires from the power source(s) screwed-in to the terminal connections.
Input voltage is 48 to 56V DC
The Switch oers built-in over current protection and power supply reverse connection
protection.

QUICK INSTALLATION GUIDE | DIS-F100G SERIES 5
Shortcut Buttons (DIP Switches)
Some advanced Switch functionality can be enabled using the Shortcut Buttons (DIP Switches).
Additional Information
You can refer to the user manual or visit https://support.dlink.com.au/ for more support.
SAFETY INSTRUCTIONS
The following general safety guidelines are provided to help ensure your own
personal safety and protect your product from potential damage. Remember to
consult the product user instructions for more details.
• Static electricity can be harmful to electronic components. Discharge static
electricity from your body (i.e. touching grounded bare metal) before touching
the product.
• Do not attempt to service the product and never disassemble the product.
For some products with user replaceable battery, please read and follow the
instructions in the user manual.
• Do not spill food or liquid on your product and never push any objects into
the openings of your product.
• Do not use this product near water, areas with high humidity or condensation
unless the product is specically rated for outdoor application.
• Keep the product away from radiators and other heat sources.
• Always unplug the product from mains power before cleaning and use a dry
lint free cloth only.
DIP Switch Function when in ON position
AI VLAN
Isolates RJ45 ports from each other, suppress network storms and
improves network performance. Uplink SFP ports continue to
communicate with all ports.
AI Extend Enables Long Reach PoE delivery up to 250m on PoE ports. Port speed
changes to 10Mbps (Cat 5 or better cabling is recommended)
AI PoE
Automatically restart a remote device by disabling and re-enabling
PoE on the port if it detects the remote device has locked up
(no incoming trac).
AI QOS Enables application prioritisation. Trac with higher priority
(e.g. Voice over IP) will be forwarded ahead of the queue.