D-Link DI-724GU - Wireless 108G QoS Gigabit Office... User manual

Wireless G USB 2.0 Adapter
Wireless Internet Camera
with 3G Mobile Video

2D-Link DI-724GU Quick Install Guide
System Requirements
• Ethernet-based Cable or DSL Modem
• Computers with Windows®, Macintosh®, or Linux-based operating
systems with an installed Ethernet adapter
• Internet Explorer 6.x and above, or Netscape® Navigator 7.0 and
above
Package Contents
D-Link DI-724GU
Wireless 108G QoS Gigabit Router
System Requirements
If any of the above items are missing, please contact your reseller.
CAT5 Ethernet Cable Power Adapter
CD-ROM with
Manual

3 D-Link DI-724GU Quick Install Guide
Hardware Overview
Hardware Overview
Power LED
A solid light indicates a
proper connection to the
power supply.
USB LED
A solid light indicates a connection
to the USB port. This LED blinks
during data transmission.
Status LED
A blinking light indicates that
the DI-724GU is functioning
properly.
WLAN LED
A solid light indicates that the wireless
segment is ready. This LED blinks
during wireless data transmission.
Local Network LEDs
A solid light on each port
indicates a connection to
an Ethernet enabled device.
These LEDs blink during data
transmission.
WAN LED
A solid light indicates a connection
on the WAN port. This LED blinks
during data transmission.

4D-Link DI-724GU Quick Install Guide
Hardware Overview
USB Port
Connection for a USB printer.
LAN Ports
These are the connections for Ethernet cables to
Ethernet-enabled computers.
Power Receptor
WAN Port
This is for the connection of an Ethernet
cable to your Cable or DSL modem.
Reset Button
Pressing this button restores the Router to
its original factory default settings.
Antennas
Used to connect to 802.11g or
802.11b wireless adapters.

5 D-Link DI-724GU Quick Install Guide
Hardware Installation
Hardware Installation
A. First, connect the power adapter to the receptor at the back panel
of the DI-724GU and then plug the other end of the power adapter
to a wall outlet or power strip. The Power LED will turn ON to
indicate proper operation.
B. 1. Power off your Cable or DSL modem; some devices may not have
a on/off switch and will require you to unplug the power adapter.
Now, the DI-724GU should be powered on and the Cable/DSL
modem should be turned off.
2. Cable/DSL modem (Power Off) – DI-724GU (Power On) Connect
an Ethernet cable to the Ethernet jack located on the Cable/DSL
modem. After the Ethernet cable is securely connected, power on
the Cable/DSL modem by turning on the unit or plugging in the
power adapter.
3. Cable/DSL modem (Power On) – DI-724GU (Power On) Insert
the other end of the Ethernet cable to the WAN PORT on the
back panel of the DI-724GU. The WAN LED light will illuminate
to indicate proper connection. If the WAN LED is not illuminated,
please go back to step B1 and repeat the instructions.
C. Insert an Ethernet cable to LAN port 1 on the back panel of the
DI-724GU and an available Ethernet port on the network adapter
in the computer you will use to configure the DI-724GU. The LED
light for LAN Port 1 will illuminate to indicate proper connection.
Note: The LAN Ports on the DI-724GU are Auto-MDI/MDIX.
Meaning you can use a straight-through or crossover Ethernet
cable to the LAN Ports.
D. Computers equipped with 802.11g wireless adapters will be able
to connect to the DI-724GU. The DWL-G650 AirPlus Xtreme G
Wireless Cardbus Adapter and the DWL-G520 AirPlus Xtreme G
Wireless PCI Adapter will be able to connect out of the box with
the router using their default wireless settings.

6D-Link DI-724GU Quick Install Guide
Getting Started
Please remember that D-Link Wireless 108G devices are pre-configured
to connect together, right out of the box, with their default settings.
Getting Started Configuration

7 D-Link DI-724GU Quick Install Guide
Configuration
This section will show you how to configure your new D-Link Wireless
108G QoS Gigabit Router using the D-Link Setup Wizard.
Configuration
Click Log In
Click Run Wizard
Open your Web browser and type
“http://192.168.0.1” into the URL
address box. Then press the Enter
or Return key.
Select “Admin” from the
User Name drop down menu
and leave the password field
blank.

8D-Link DI-724GU Quick Install Guide
Configuration
Click Next
Click Next
Click Next
You have the option to establish
a password for the User Name
“Admin”.
Choose your time zone from the
drop down list.

9 D-Link DI-724GU Quick Install Guide
Configuration
Click Next
Dynamic IP Address
Click Next
Continue to page 15
You will be prompted to select the type of Internet connection for your
router. If you are unsure of which setting to select, please contact
your Internet Service Provider.
Static IP Address - page 10
PPPoE - page 11
PPTP - page 12
L2TP - page 13
Big Pond - page 14
If you selected Dynamic IP Address, this screen will appear: (Used
mainly for Cable Internet service).
Click the “Clone MAC Address”
button to automatically copy the
MAC address of the network
adapter in your computer. You can
also manually type in the MAC
address.

10D-Link DI-724GU Quick Install Guide
Configuration
Click Next
Static IP Address
Click Next
Continue to page 15
If your ISP requires a Static
IP Address, please select the
corresponding radio button.
Enter the IP address that
was originally provided to you
by your ISP. You will need to
complete all of the required
fields.