D-Link DVG-G1402S - Wireless Broadband VoIP Router Quick guide

DVG-G1402S Configuration for GOtalk
In the following guide we will cover all of the settings required to configure your DVG-G1402S with your
GOtalk VoIP Account.
Factory Reset
It is recommended to factory reset your router before we proceed with the correct settings to ensure that
all the settings that we enter are stored correctly. To factory reset the unit power on the unit and wait for
it to be in a system idle state (about 30-40 seconds after power on) then press and hold the Factory Reset
button. Continue to hold the Factory Reset button for 10-15 seconds then release; this will then restart
the unit In a Factory Default state.
Reset Button is shown above by the red arrow
Accessing the Web Interface
Now to configure your unit from scratch we will need to connect to the interface via a Web Browser. Any
browser will be fine but for this guide we will be using Internet Explorer 6.0 (IE6). To log into the router
open up IE6 and type “http://192.168.15.1” into the address bar. This will now prompt you for a
username and password to configure the DVG-G1402S as shown below:
Username: “admin”, Password: “admin”
You will now need to enter the username and password to access the device. The username will be
“admin” and the password is also “admin”. Once you have entered the username and password press the
OK button.

Configuring the Connection to the Internet
Now that we have accessed the DVG-G1402S’s Web Interface we will now need to configure the router for
Internet connection. Select Home tab on top and then click on WAN button on the left.
You will see several options for different types of Internet connections. It is very common for broadband
modems to carry out the authentication process, so all you need to do on your router is to set it to the
“Dynamic IP Address” option (it is selected by default). If your provider requires PPPoE login and your
modem does not have PPPoE built in (so you had to run PPPoE client on your computer when the modem
was connected to your PC), select the PPPoE option. Specify your ISP’s account username and password.
If you have one of the recent broadband modems which are capable of handling the authentication with
your ISP, leave your router on the “Dynamic IP” option.
Click on Apply when done.
P.S. If you are connecting to Bigpond Cable you will need to select the “Dynamic IP” option in the router
and run the login software on your computer(s). We recommend using the BPALogin client:
http://www.dlink.com.au/tech/faqs/default.asp?model=DVG-G1402S&TemplateId=23678

Configuring the SIP Server for GOtalk
We now need to configure the SIP Settings for your GOtalk VoIP Account. This is done by clicking on the
Home tab at the top of the page and then selecting the VoIP button in the left hand navigation bar. You
should see the below page appear:
From the above selection press on Server Configuration. This will now bring up the SIP Server
configuration page as shown over the page. We will need to change the below settings:
Server FQDN: Enabled
Domain Name: sip.gotalk.com
Secondary Server FQDN: Enabled
Secondary Domain Name: sip.gotalk.com
Secondary Port: 5060
Outbound Proxy State: Enabled
Outbound Proxy Sever FQDN: Enabled
Outbound Proxy Domain Name: sip.gotalk.com
Outbound Proxy Port: 5060
Service Domain: sip.gotalk.com
User Parameter Phone: Disabled
Register Expiration: 240
Once all of the settings have been entered it should look like the below, if all is correct then click on the
Apply button to save these changes.

In order to save these changes permanently we will need to do a Reboot of that router but for now just
click on the OK button and we will Save the settings and Reboot the router when all settings are
completed.
Ok now that we have changed all of the SIP Server settings scroll to the bottom of the page and click on
the Back button to return to the main VoIP configuration page.
Configuring the VoIP Phone Account
Now that we have configured the correct values for the GOtalk SIP Server we can now setup the Phone
Account, to do this select User Agent. This will now show the below page and allow us to setup the
Phone Number and logins for VoIP account.
We now need to enter in your settings to get your account to become active. Below is a list of the settings
that you will need to enter into this page:

Same Phone Number: Enabled
Phone Number: <GOtalk Username>
Display Name: <GOtalk Username> or a name to be shown while using Caller ID
Authentication Username: <GOtalk Username>
Password: <GOtalk Password>
Retype Password: <GOtalk Password>
** Please note that you can find your GOtalk Username and Password on a white sticker on the underside of the DVG-G1402S **
Once you have entered all of the above settings into the unit click on the Apply button to Save the
settings. Once again you will see the below message box appear, just click on OK.
We have now configured the unit with all the SIP Server Settings and the Phone Account Settings. The
last thing left to do is save and reboot the unit.
Saving the Settings and Restarting the Router
In order to make all of the above changes effective and save them permanently we will need to click on
Tools at the top of the page then click on Reboot from the left hand navigation bar. This will now show the
below page:
Now click on the Reboot button. This will then Save and reboot the router. You will see the below bar
while the unit is restarting, when the unit is ready it will prompt you for the Web Interface login again.
The DVG-G1402S is now setup for the VoIP account. Your unit should now be connected to the Internet
and allow for you to make VoIP Phone Calls.