D-Link Ethernet Broadband Router DIR-100 User manual

Quick Install Guide
DIR-100
Version 1.00

2
System Requirements
• Ethernet-based Cable or DSL Modem
• Computers with Windows®, Macintosh®, or Linux-based operating
systems with an installed Ethernet adapter
• Internet Explorer 6.x and above, or Netscape®Navigator 7.0 and
above
Package Contents
System Requirements
If any of the above items are missing, please contact your reseller.
CAT5 Ethernet Cable Power Adapter
D-Link DIR-100 CD-ROM with
Manual

3
Hardware Overview
Hardware Overview
Status LED
A blinking light indicates that
the DIR-100 is functioning
properly.
Local Network LEDs
Asolid light on each port indicates
a connection to an Ethernet
enabled device. These LEDs
blink during data transmission.
WAN LED
A solid light indicates a connection
on the WAN port. This LED blinks
during data transmission.
Power LED
A solid light indicates a
proper connection to the
power supply.

4
Hardware Overview
LAN Ports
These are the connections for Ethernet cables to
Ethernet-enabled computers.
WAN Port
This is for the connection of an Ethernet
cable to your Cable or DSL modem.
Reset Button
Pressing this button
restores the Router
to its original factory
default settings.
Power Receptor

5
Hardware Installation
Hardware Installation
A. First, connect the power adapter to the receptor at the back panel
of the DIR-100 and then plug the other end of the power adapter
to a wall outlet or power strip. The Power LED will turn ON to
indicate proper operation.
B.1. Power off your Cable or DSL modem; some devices may not
have a on/off switch and will require you to unplug the power
adapter. Now, the DIR-100 should be powered on and the Cable/
DSL modem should be turned off.
2. Cable/DSL modem (Power Off) – DIR-100 (Power On) Connect
an Ethernet cable to the Ethernet jack located on the Cable/DSL
modem. After the Ethernet cable is securely connected, power
on the Cable/DSL modem by turning on the unit or plugging in
the power adapter.
3. Cable/DSL modem (Power On) – DIR-100 (Power On) Insert
the other end of the Ethernet cable to the WAN PORT on the back
panel of the DIR-100. The WAN LED light will illuminate to indicate
proper connection. If the WAN LED is not illuminated, please go
back to step B1 and repeat the instructions.
C.Insert an Ethernet cable to LAN port 1 on the back panel of the
DIR-100 and an available Ethernet port on the network adapter
in the computer you will use to congure the DIR-100. The LED
light for LAN Port 1 will illuminate to indicate proper connection.
Note: The LAN Ports on the DIR-100 are Auto-MDI/MDIX.
Meaning you can use a straight-through or crossover Ethernet
cable to the LAN Ports.
D.Computers equipped with Ethernet or Gigabit Ethernet adapters
will be able to connect to the DIR-100. The DFE-530TX or DGE-
530T PCI Adapters (as examples) will be able to connect with the
router without any additional conguration required.

6
Getting Started
Getting Started

7
Conguration
This section will show you how to congure your new D-Link DIR-100
Router using the D-Link Setup Wizard.
Conguration
Click Log In
Click Setup Wizard
Open your Web browser and type
“http://192.168.0.1” into the URL
address box. Then press the Enter
or Return key.
Type “admin” for the user-
name and leave the pass-
word eld blank.

8
Conguration
Click Next
Click Next
Click Next
You have the option to establish
a password for the User Name
“Admin”.
Choose your time zone from the
drop down list.
Click Setup Wizard

9
Conguration
You will be prompted to select the type of Internet connection for your
router. If you are unsure of which setting to select, please contact
your Internet Service Provider.
PPPoE - page 10
PPTP - page 11
L2TP - page 12
Big Pond - page 13
Static IP Address - page 14
If you selected Dynamic IP Address, this screen will appear: (Used
mainly for Cable Internet service).
Click Next
Dynamic IP Address
Click Next
Continue to page 15
Click the “Clone MAC Address”
button to automatically copy the
MAC address of the network
adapter in your computer. You
can also manually type in the
MAC address.

10
Conguration
PPPoE
Click Next
Click Next
Continue to page 15
Note: Please be sure to remove any existing PPPoE client software
installed on your computers.
If your ISP uses PPPoE
(Point-to-Point Protocol
over Ethernet), select the
corresponding radio button.
If you have a Dynamic IP
connection, enter the User
Name and Password provided
to you by your ISP.

11
Conguration
If your ISP uses PPTP (Point
to Point Tunneling Protocol),
select the corresponding radio
button.
If you have a Dynamic IP
connection, enter the Server IP,
PPTP Account, and Password
provided to you by your ISP.
If you have a Static IP
connection, enter the IP
Address, Subnet Mask,
Gateway IP Address, Server
IP, PPTP Account, and
Password provided to you by
your ISP.
PPTP
Click Next
Click Next
Continue to page 15
Click Next

12
Conguration
L2TP
Click Next
Click Next
Continue to page 15
If your ISP uses L2TP (Layer
Two Tunneling Protocol),
select the corresponding radio
button.
If you have a Dynamic IP
connection, enter the L2TP
Server IPAddress, User Name,
and Password provided to you
by your ISP.
If yo u h ave a S t a t ic I P
connection, enter the L2TP
IP Address, Subnet Mask,
Gateway IP Address, L2TP
Server IP, User Name, and
Password provided to you by
your ISP.
Click Next

13
Conguration
Big Pond
Click Next
Continue to page 15
Select this option if you connect
to the internet through Telstra
BigPond Cable Broadband in
Australia.
Enter the User Name, and
Password provided to you by
your ISP.
Click Next

14
Conguration
Static IP Address
Click Next
Continue to page 15
If your ISP requires a Static
IP Address, please select the
corresponding radio button.
Enter the IP address that was
originally provided to you by
your ISP. You will need to
complete all of the required
elds.
Click Next

15
Conguration
Click Restart
For additional settings or information, refer to the Advanced, Tools,
or Status tabs on the web-management interface; or to the Manual
located on the CD.
You will be returned to the Home tab. Close this web browser window
and open a new one (i.e., Internet Explorer or Netscape®Navigator).
Link to your favorite Web site to test your Internet connection.
Your Setup is Complete!
Test Internet Connection

16
Appendix
Appendix
To connect to the network, make sure
the network adapter in your computer
is configured properly. Here’s how to
congure the network adapter to obtain
an IP address automatically when using
the DIR-100 Router.
For Microsoft Windows®XP:
Right click on My Network Places
and select Properties. Right click
on the Network Connection
associated with the Ethernet adapter
and select Properties (i.e., D-Link
DFE-530TX+).
Click OK
Click OK
Select Obtain an IP Address
automatically.
Click Internet Protocol (TCP/IP)
and then click Properties.

17
Appendix
For Apple Macintosh®OS X:
Go to the Apple Menu and click on
System Preferences, and select
Network.
The IP address information,
the Subnet Mask, the Router’s
IP address, and the Ethernet
adapter address will appear.
Click Network
Select Built-in Ethernet in
the Show pull down menu.
Select Using DHCP in the
Congure pull down menu.
Click Apply Now and restart
your computer (if necessary).

Technical Support
You can nd software updates and user documentation on the
D-Link website.
Tech Support for customers within Australia:
D-Link Technical Support over the Telephone:
1300-766-868
Monday to Friday 8:00am to 8:00pm EST
Saturday 9:00am to 1:00pm EST
D-Link Technical Support over the Internet:
http://www.dlink.com.au
email:[email protected]
Tech Support for customers within New
Zealand:
D-Link Technical Support over the Telephone:
0800-900-900
Monday to Friday 8:30am to 8:30pm
Saturday 9:00am to 5:00pm
D-Link Technical Support over the Internet:
http://www.dlink.co.nz
email:[email protected]

Technical Support
You can nd software updates and user documentation on the
D-Link website.
Tech Support for customers within South
Eastern Asia and Korea:
D-Link South Eastern Asia and Korea Technical Support
over the Telephone:
[phone]
Monday to Friday 9:00am to 12:30pm, 2:00pm-6:00pm
Singapore Time
D-Link Technical Support over the Internet:
email:[email protected]

Technical Support
You can nd software updates and user documentation on the
D-Link website.
Tech Support for customers within India
D-Link Technical Support over the Telephone:
[phone]
[phone] –ext 161 to 167
Monday to Friday 9:30am to 7:00pm
D-Link Technical Support over the Internet:
http://ww.dlink.co.in
http://www.dlink.co.in/dlink/drivers/support.asp
ftp://support.dlink.co.in
email: [email protected]