D-Link DWR-712 User manual

USER MANUAL

iD-Link DWR-712 User Manual
D-Link reserves the right to revise this publication and to make changes in the content hereof without obligation to notify
any person or organization of such revisions or changes.
Trademarks
D-Link and the D-Link logo are trademarks or registered trademarks of D-Link Corporation or its subsidiaries in the United
States or other countries. All other company or product names mentioned herein are trademarks or registered trademarks
of their respective companies.
Copyright © 2013 by D-Link Corporation, Inc.
All rights reserved. This publication may not be reproduced, in whole or in part, without prior expressed written permission
from D-Link Corporation, Inc.
Preface

iiD-Link DWR-712 User Manual
Table of Contents
Product Overview.............................................................. 1
Package Contents......................................................................... 1
System Requirements................................................................. 1
Introduction ................................................................................... 2
Hardware Overview..................................................................... 3
Rear Panel................................................................................ 3
Front Panel .............................................................................. 4
LEDs........................................................................................... 5
Installation ......................................................................... 6
Connect to Your Network .......................................................... 6
Wireless Installation Considerations...................................... 7
Conguration..................................................................... 8
Web-based Conguration Utility............................................ 8
Setup................................................................................................. 9
Internet..................................................................................... 9
Internet Connection Setup Wizard............................ 9
Manual Internet Connection Setup ........................12
Internet Connection .....................................................12
Static IP..............................................................................13
Dynamic IP (DHCP)........................................................14
PPPoE .................................................................................15
PPTP....................................................................................17
L2TP ....................................................................................18
3G ........................................................................................19
Wireless Settings.................................................................21
Wireless Connection Setup Wizard..........................21
Manual Wireless Connection Setup ........................23
Wireless Settings ............................................................24
Wireless Security Mode ...............................................25
Wi-Fi Protected Setup .......................................................28
Network Settings ................................................................30
Router Settings...............................................................30
DHCP Server Settings...................................................31
Message Service..................................................................32
SMS Inbox.........................................................................32
Create Message ..............................................................33
Advanced ......................................................................................34
Virtual Server........................................................................34
Application Rules................................................................36
QoS Engine............................................................................37
MAC Address Filter.............................................................38
URL Filter................................................................................39
Outbound Filter...................................................................40
Inbound Filter ......................................................................41
SNMP.......................................................................................42
Routing...................................................................................43
Advanced Wireless .............................................................44
Advanced Network ............................................................45
DMZ .........................................................................................46
Tools ................................................................................................47
Admin .....................................................................................47
Table of Contents

iiiD-Link DWR-712 User Manual
Table of Contents
Time.........................................................................................48
Syslog......................................................................................49
E-mail Settings.....................................................................50
System ....................................................................................51
Firmware ................................................................................52
Dynamic DNS .......................................................................53
System Check.......................................................................54
Schedules ..............................................................................55
Connection Reset ...............................................................56
Status ..............................................................................................57
Device Info ............................................................................57
Log ...........................................................................................58
Statistics .................................................................................59
Wireless ..................................................................................60
Support ..........................................................................................61
Connecting to a Wireless Network .................................62
Using Windows 7 .......................................................................62
Conguring Wireless Security ........................................64
Using Windows Vista™ ..............................................................67
Conguring Wireless Security ........................................68
Using Windows®XP ....................................................................70
Congure WEP .....................................................................71
Congure WPA-PSK............................................................73
Troubleshooting ..............................................................75
Wireless Basics .................................................................77
What is Wireless?.........................................................................78
Tips...................................................................................................80
Wireless Modes............................................................................81
Networking Basics...........................................................82
Check your IP address...............................................................82
Statically Assign an IP address...............................................83
Technical Specications..................................................84

1D-Link DWR-712 User Manual
Section 1 - Product Overview
• D-Link DWR-712 HSPA+ 3G Router
• Power adapter
• Manual and Warranty on CD
• Antenna
Note: Using a power supply with a dierent voltage rating than the one included with the DWR-712 will cause damage and void the warranty for
this product.
System Requirements
• A compatible (U)SIM card with service.*
• Computers with Windows®, Macintosh®, or Linux-based operating system with an installed Ethernet adapter
• Internet Explorer 6 or Netscape Navigator™ Version 6.0 and above (for conguration)
*Subject to services and service terms available from your carrier.
Product Overview
Package Contents

2D-Link DWR-712 User Manual
Section 1 - Product Overview
Introduction
The D-Link HSPA+ 3G Router allows users to access worldwide mobile broadband networks. Once connected, users can
transfer data, stream media, and send SMS messages. Simply insert your UMTS/HSUPA SIM card, and share your 3G Internet
connection through a secure 802.11n wireless network or using any of the four 10/100 Ethernet ports.
Keep your wireless network safe with WPA/WPA2 wireless encryption. The DWR-712 utilizes dual-active rewalls (SPI and
NAT) to prevent potential attacks across the Internet, and includes MAC address ltering to control access to your network.
The HSPA+ 3G Router can be installed quickly and easily almost anywhere. This router is great for situations where an
impromptu wireless network must be set up, or wherever conventional network access is unavailable. The DWR-712 can
even be installed in buses, trains, or boats, allowing passengers to check e-mail or chat online while commuting.

3D-Link DWR-712 User Manual
Section 1 - Product Overview
Hardware Overview
Rear Panel
Port Function
LAN Ports
(RJ-45)
Connects to a network device such as a desktop or notebook
computer through an Ethernet cable.
WAN (RJ-45) Connects to a DSL/Cable modem or router through an Ethernet
cable.
SIM Accepts a standard (U)SIM card for 3G connectivity.
Power Connects to the included power adapter.
Power Switch Turns the device on or o.
Phone Port Connect to a regular phone line.
LAN Ports
Power ConnectorWAN Port
SIM Card Slot Power Switch
Phone Port

4D-Link DWR-712 User Manual
Section 1 - Product Overview
Hardware Overview
Front Panel
Status 2G 3G SMS WLAN
WAN LAN1 LAN2 LAN3 LAN4
Signal Strength Reset Button WPS Button
Button Name Function
Reset Press this button with an unfolded paperclip to reset
the device.
WPS Press this button to initiate a new WPS connection.

5D-Link DWR-712 User Manual
Section 1 - Product Overview
LED Name Function
Status Blinking Green: Device is working
WAN Solid Green: Ethernet connection has been established
Blinking Green: Data is being transferred
LAN 1-4 Solid Green: Ethernet connection has been established
Blinking Green: Data is being transferred
Signal
Strength
Blinking Red: No SIM card / signal or unveried PIN code
Solid Red: Signal strength is at level one (weak)
Solid Amber: Signal strength is at level two or three (medium)
Solid Green: Signal strength is at level four or ve (strong)
WPS Slow Blinking Green: WPS is functioning normally
Fast Blinking Green: WPS is functioning in PBC mode
2G Solid Green: EDGE or GPRS connection has been established
Blinking Green: Data is being transferred via 2G/2.5G
3G Solid Green: UMTS/HSDPA/HSUPA connection is established
Blinking: Data is being transferred via 3G/3.75G
SMS Solid Green: SMS storage is full
Blinking Green: There is an unread SMS message
WLAN Solid Green: WLAN is active and available
Blinking Green: Data is being transferred over the WLAN
Hardware Overview
LEDs

6D-Link DWR-712 User Manual
Section 2 - Installation
Connect to Your Network
Installation
This section will guide you through the installation process. Placement of the router is very important. Do not place the router in an enclosed area
such as a closet, cabinet, or in an attic or garage.
1. Ensure that your DWR-712 HSPA+ 3G Router is disconnected and powered o.
2. Insert a standard (U)SIM card into the SIM card slot on the back of the router as indicated by the SIM card logo next to the slot. The gold contacts
should face downwards.
Caution: Always unplug/power down the router before installing or removing the SIM card. Never insert or remove the SIM card while the router
is in use.
3. Insert your Internet/WAN network cable into the WAN port on the back of the router.
Note: The 3G connection can also be used as a backup WAN. Once a backup is congured, the router will automatically use 3G for the Internet
connection if the Ethernet WAN is not available.
4. Insert the Ethernet cable into the LAN Port 1 on the back panel of the DWR-712 HSPA+ 3G Router and an available Ethernet port on the network
adapter in the computer you will use to congure the router.
Note: The DWR-712 HSPA+ 3G Router LAN Ports are Auto-MDI/MDIX, so both patch and crossover Ethernet cables can be used.
5. Connect the power adapter to the socket on the back panel of your DWR-712 HSPA+ 3G Router. Plug the other end of the power adapter into
a wall outlet or power strip and turn the device on.
a. The Status LED will light up to indicate that power has been supplied to the router.
b. The LEDs on the front panel will ash on and o as the DWR-712 HSPA+ 3G Router performs initialization and Internet connection processes.
c. After a few moments, if a connection has been established, the following LEDs will turn solid green: Power, Status, WAN, WLAN, and any LAN
Port LEDs that are connected computers or other devices.

7D-Link DWR-712 User Manual
Section 2 - Installation
Wireless Installation Considerations
The DWR-712 can be accessed using a wireless connection from virtually anywhere within the operating range of your wireless network. Keep in
mind that the quantity, thickness, and location of walls, ceilings, or other objects that the wireless signals must pass through may limit the range
of the wireless signal. Ranges vary depending on the types of materials and background RF (radio frequency) noise in your home or oce. The key
to maximizing the wireless range is to follow these basic guidelines:
1. Minimize the number of walls and ceilings between the D-Link router and other network devices. Each wall or ceiling can reduce your adapter’s
range from 3 to 90 feet (1 to 30 meters).
2. Be aware of the direct line between network devices. A wall that is 1.5 feet thick (0.5 meters), at a 45-degree angle appears to be almost 3 feet
(1 meter) thick. At a 2-degree angle it looks over 42 feet (14 meters) thick. Position devices so that the signal will travel straight through a wall
or ceiling (instead of at an angle) for better reception.
3. Try to position access points, wireless routers, and computers so that the signal passes through open doorways and drywall. Materials such as
glass, metal, brick, insulation, concrete, and water can aect wireless performance. Large objects such as sh tanks, mirrors, le cabinets, metal
doors, and aluminum studs may also have a negative eect on range.
4. If you are using 2.4 GHz cordless phones, make sure that the 2.4 GHz phone base is as far away from your wireless device as possible. The base
transmits a signal even if the phone is not in use. In some cases, cordless phones, X-10 wireless devices, and electronic equipment such as ceiling
fans, uorescent lights, and home security systems may dramatically degrade wireless connectivity.

8D-Link DWR-712 User Manual
Section 3 - Conguration
Conguration
This section will show you how to congure your new D-Link mobile router using the web-based conguration utility.
Web-based Conguration Utility
To access the conguration utility, open a web-browser such as Internet Explorer and enter
the IP address of the router (192.168.0.1 by default).
To log in to the conguration utility, enter admin as the username, and then enter the password.
By default, the password is blank.
If you get a Page Cannot be Displayed error, please refer to the Troubleshooting section
for assistance.
The conguration utility will open to the STATUS > DEVICE INFO page. You can view dierent
conguration pages by clicking on the categories at the top of the screen (SETUP/ADVANCED/
TOOLS/STATUS/SUPPORT), and then selecting a conguration page from the bar on the left side.
The following pages will describe each section in detail, starting with the SETUP pages.

9D-Link DWR-712 User Manual
Section 3 - Conguration
Setup
This wizard will guide you through a step-by-step process to congure your D-Link router to
connect to the Internet.
Click Next to continue.
Note: While using the wizard, you can click Prev to go back to the previous page or you can
click Cancel to close the wizard.
Internet Connection Setup Wizard
The SETUP pages allow you to congure your Internet and wireless settings, as well as manage
your SMS inbox. To view the Setup conguration pages, click on SETUP at the top of the screen.
The Internet page allows you to congure how your router connects to the Internet. There are
two ways to set up your Internet connection.
You can click on the Internet Connection Setup Wizard button to start a wizard that will
guide you through setting up your Internet settings.
If you want to manually congure your settings, click Manual Internet Connection Setup
and skip to “Manual Internet Connection Setup”on page 12.
Internet

10D-Link DWR-712 User Manual
Section 3 - Conguration
Create a new password and then click Next to continue.
Select the Internet connection type you use. The connection types are explained on the
following page. If you are unsure which connection type you should use, contact your Internet
Service Provider (ISP).
Click Prev to go back to the previous page or click Cancel to close the wizard.
Note: The DWR-712 has a WAN Failover feature that allows the router to switch to a 3G
connection if the WAN connection is down or unavailable. To congure this feature,
please refer to “Internet Connection” on page 12.
Select your time zone from the drop-down box and then click Next to continue.

11D-Link DWR-712 User Manual
Section 3 - Conguration
Choose this if your Internet connection automatically provides you with an IP Address. Most cable modems use
this type of connection. See“Dynamic IP (DHCP)” on page 14 for information about how to congure this type of
connection.
Choose this option if your Internet connection requires a username and password to connect. Most DSL modems
use this style of connection. See“PPPoE” on page 15 for information about how to congure this type of
connection.
Choose this option if your Internet connection requires Point-to-Point Tunneling Protocol (PPTP). See “PPTP”on
page 17 for information about how to congure this type of connection.
Choose this option if your Internet connection requires Layer 2 Tunneling Protocol (L2TP). See “L2TP” on page 18
for information about how to congure this type of connection.
Choose this connection if you have installed a SIM card into the DWR-712. See“3G” on page 19 for information
about how to congure this type of connection.
Choose this option if your Internet Setup Provider provided you with IP Address information that has to be
manually congured. See“Static IP” on page 13 for information about how to congure this type of connection.
DHCP Connection
(Dynamic IP Address):
Username / Password
Connection (PPPoE):
Username / Password
Connection (PPTP):
Username / Password
Connection (L2TP):
3G Connection:
Static IP Address
Connection:
The subsequent conguration pages will dier depending on the selection you make on this page.
After entering the requested information,click Next to continue.
This completes the Internet Connection Setup Wizard. Click Connect to save your changes
and reboot the router.

12D-Link DWR-712 User Manual
Section 3 - Conguration
Manual Internet Connection Setup
To set up your Internet connection manually, click Manual Internet Connection Setup.
My Internet Connection
is:
Host Name:
Auto-Backup:
Internet Host:
Several dierent Internet Connection types can be selected depending upon the specications of your Internet Service Provider (ISP). You can also
set up the Auto-Backup feature, which allows you to use a 3G connection for your Internet connection if your main connection fails.
Internet Connection
Select the Internet Connection type specied by your Internet
Service Provider (ISP). The corresponding settings will be
displayed below. Please see the following pages for details on
how to congure these dierent connection types.
If the Internet Host you are using for the Auto-Backup feature
requires you to enter a Host Name, enter it here. In most cases,
you may leave this blank.
When this box is checked, the router will switch over to
a 3G connection if the Internet Host (specied below) is
unreachable.
Enter an IP address for the router to use to check if it is
connected to the Internet. If Auto-Backup is enabled and the
IP address cannot be reached, the router will switch over to a
3G connection.

13D-Link DWR-712 User Manual
Section 3 - Conguration
Enter the IP address assigned to your network connection.
Enter the subnet mask.
Enter the default gateway.
Enter the primary DNS server.
Enter the secondary DNS server.
You may need to change the Maximum Transmission Unit
(MTU) for optimal performance. The default value is 1500.
The default MAC Address is set to the Internet port’s physical
interface MAC address on the Broadband Router. It is not
recommended that you change the default MAC address
unless required by your ISP. You can use the Clone Your PC’s
MAC Address button to replace the Internet port’s MAC
address with the MAC address of your Ethernet card.
IP Address:
Subnet Mask:
Default Gateway:
Primary DNS Server:
Secondary DNS Server:
MTU:
MAC Address:
Choose this Internet connection if your ISP assigns you a static IP address. After modifying any settings, click Save Settings to save your changes.
Static IP

14D-Link DWR-712 User Manual
Section 3 - Conguration
Dynamic IP (DHCP)
This section will help you to obtain IP Address information automatically from your ISP. Use this option if your ISP didn’t provide you with IP Address
information and/or a username and password. After modifying any settings, click Save Settings to save your changes.
(Optional) Fill in with IP address of primary DNS server.
(Optional) Fill in with IP address of secondary DNS server.
You may need to change the Maximum Transmission Unit
(MTU) for optimal performance. The default value is 1500.
The default MAC Address is set to the Internet port’s physical
interface MAC address on the Broadband Router. It is not
recommended that you change the default MAC address
unless required by your ISP. You can use the Clone Your PC’s
MAC Address button to replace the Internet port’s MAC
address with the MAC address of your PC.
This feature enables this product to renew the WAN IP address
automatically when the lease time has expired.
Primary DNS Server:
Secondary DNS Server:
MTU (Maximum
Transmission Unit):
MAC Address:
Auto-reconnect:

15D-Link DWR-712 User Manual
Section 3 - Conguration
PPPoE
Choose this Internet connection if your ISP provides you PPPoE account. After modifying any settings, click Save Settings to save your changes.
The username/account name that your ISP provides to you for
PPPoE dial-up.
Password that your ISP provides to you for PPPoE dial-up.
Fill in with the same password in Password eld.
Choose Always-on when you want to establish PPTP
connection all the time. If you choose Connect-on-demand,
the device will establish PPTP connection when local users
want to surf Internet, and disconnect if no trac after time
period of Maximum Idle Time.
(Optional) Fill in if provided by your ISP.
(Optional) Fill in if provided by your ISP. If not, keep the default
value.
(Optional) Fill in if provided by your ISP. If not, keep the default
value.
(Optional) Fill in if provided by your ISP. If not, keep the default
value.
Username:
Password:
Verify Password:
Reconnect Mode:
Service Name:
IP Address:
Primary DNS Server:
Secondary DNS Server:

16D-Link DWR-712 User Manual
Section 3 - Conguration
MAC address of WAN interface. You can also copy MAC address
of your PC to its WAN interface by pressing Clone Your PC’s
MAC button. The Restore MAC button will reset the router to
its default MAC address.
The amount of time of inactivity before disconnecting
established PPPoE session. Set it to zero or enable Auto-
reconnect will disable this feature.
The default setting of PPPoE is 1492.
MAC Address:
Maximum Idle Time:
Maximum Transmission
Unit (MTU):