DAB ACTIVE J 62 Operating and maintenance manual

ISTRUZIONI PER L'INSTALLAZIONE E LA MANUTENZIONE
INSTRUCTIONS DE MISE EN SERVICE ET D'ENTRETIEN
INSTRUCTIONS FOR INSTALLATION AND MAINTENANCE
INSTALLATIONSANWEISUNG UND WARTUNG
INSTRUCTIES VOOR INGEBRUIKNAME EN ONDERHOUD
INSTRUCCIONES PARA LA INSTALACION Y EL MANTENIMIENTO
INSTALLATIONS - OCH UNDERHÅLLSANVISNING
Ο∆ΗΓΙΕΣ ΓΙΑ ΤΗΝ ΕΓΚΑΤΑΣΤΑΣΗ ΚΑΙ ΤΗ ΣΥΝΤΗΡΗΣΗ
KULLANIM VE BAKIM TALİMATLARI
ИНСТРУКЦИИ ПО МОНТАЖУ ИТЕХНИЧЕСКОМУ ОБСЛУЖИВАНИЮ
INSTRUCŢUNI PENTRU INSTALARE ŞI ÎNTREŢINERE
.ª¦Bl{A¥ J¦yZK{{ LAXBcZG

RACCORDO DI MANDATA
RACCORD DE REFOULEMENT
DELIVERY FITTING
V
ORLAUFANSCHLUSS
A
ANSLUITING VOOR PERSZIJDE
RACOR DE IMPULSIÓN
TRYCKANSLUTNING
ΕΞΑΡΤΗΜΑ (ΡΑΚΟΡ)
ΚΑΤΑΘΛΙΨΗΣ
BESLEME RAKORU
НАПОРНЫЙ ПАТРУБОК
RACORD TERMINAL AL TUBULUI DE RESPINGERE
msX{A ª{e¥
PANNELLO DI CONTROLLO
PANNEAU DE CONTRÔLE
CONTROL PANEL
STEUERPANEEL
CONTROLEPANEEL
CUADRO DE MANDOS
MANÖVERPANEL
ΠΙΝΑΚΑΣ ΕΛΕΓΧΟΥ
KONTROL PANELI
ПАНЕЛЬ УПРАВЛЕНИЯ
PANOU DE CONTROL
©XB¦w{A ªR¥{
TAPPO DI CARICO
BOUCHON DE REMPLISSAGE
FILLING CAP
FÜLLSCHRAUBE
V
ULDOP
TAPÓN DE CARGA
PÅFYLLNINGSPLUGG
ΤΑΠΑ ΠΛΗΡΩΣΗΣ
DOLDURMA TIPASI
ПРОБКА ЗАЛИВКИ
CAPAC DE ÎNCĂRCARE
ª®IlK{A ºBio
TAPPO DI SCARICO
BOUCHON DE VIDANGE
DRAINAGE CAP
A
BLASSSCHRAUBE
A
FVOERDOP
TAPÓN DE DESCARGA
TÖMNINGSPLUGG
ΤΑΠΑ ΕΚΚΕΝΩΣΗΣ
TAHLİYE TIPASI
СЛИВНАЯ ПРОБКА
CAPAC DE DESCĂRCARE
q¦ZtK{A −Bio
PIEDE DI FISSAGGIO
PIED DE FIXATION
A
NCHORING FOOT
BEFESTIGUNGSFUSS
BEVESTIGINGSVOET
PIE DE FIJACIÓN
FÄSTFOT
ΠΟ∆Ι ΣΥΓΚΡΑΤΗΣΗΣ
SABİTLEME AYAĞI
КРЕПЕЖНАЯ НОЖКА
PICIORUŞDE FIXARE
L¦IMK{A |OZ

ACTIVE J 62 ACTIVE JI 62 ACTIVE JC 62
ACTIVE J 82 ACTIVE JI 82 ACTIVE JC 82
ACTIVE J 92 ACTIVE JI 92 ACTIVE JC 92
ACTIVE J102 ACTIVE JI102 ACTIVE JC102
ACTIVE J112 ACTIVE JI112
ACTIVE J132 ACTIVE JI132 ACTIVE JC132
ACTIVE E 25/30 (6) ACTIVE EI 25/30 (6) ACTIVE EC 25/30 (6)
ACTIVE E 30/30 (6) ACTIVE EI 30/30 (6) ACTIVE EC 30/30 (6)
ACTIVE E 40/30 (6) ACTIVE EI 40/30 (6)
ACTIVE E 30/50 (6) ACTIVE EI 30/50 (6) ACTIVE EC 30/50 (6)
ACTIVE E 40/50 (6) ACTIVE EI 40/50 (6) ACTIVE EC 40/50 (6)
ACTIVE E 50/50 (6) ACTIVE EI 50/50 (6)
ACTIVE E 25/80 (6) ACTIVE EI 25/80 (6) ACTIVE EC 25/80 (6)
ACTIVE E 30/80 (6) ACTIVE EI 30/80 (6) ACTIVE EC 30/80 (6)
ACTIVE E 40/80 (6) ACTIVE EI 40/80 (6)
220 / 240 V 50-60 HZ
ACTIVE J ACTIVE JI ACTIVE JC
ACTIVE E ACTIVE EI ACTIVE EC
ACTIVE SYSTEM

DICHIARAZIONE DI CONFORMITA’
La Ditta DAB PUMPS s.p.a - Via Marco Polo, 14 - Mestrino - PD -
ITALY – sotto la propria esclusiva responsabilità dichiara che i prodotti
Active – Active System, elencati precedentemente, sono conformi a:
− Direttiva del Consiglio n° 98/37/CE e successive modifiche.
− Direttiva della Compatibilità elettromagnetica 89/336
e successive modifiche.
− Direttiva Bassa Tensione 73/23 e successive modifiche.
DÉCLARATION DE CONFORMITÉ
La Société DAB PUMPS s.p.a - Via Marco Polo, 14 - Mestrino - PD - ITALY
– sous sa propre responsabilité exclusive, déclare que les produits Active –
Active System, énumérés plus haut, sont conformes à :
− Directive du Conseil n° 98/37/CE et modifications successives.
− Directive de la Compatibilité électromagnétique n°89/336
et modifications successives.
− Directive Basse Tension 73/23 et modifications successives.
DECLARATION OF CONFORMITY
The Company DAB PUMPS s.p.a - Via Marco Polo, 14 - Mestrino - PD -
ITALY – under its own exclusive responsibility declares that the products
Active – Active System, listed above, comply with:
− Council Directive n° 98/37/CE and subsequent modifications.
− Directive on electromagnetic Compatibility 89/336 and subsequent
modifications.
− Directive on Low Voltage 73/23 and subsequent modifications.
KONFORMITÄTSERKLÄRUNG
Die Firma DAB PUMPS s.p.a - Via Marco Polo, 14 - Mestrino - PD - ITALY
– erklärt eigenverantwortlich, dass die vorstehend beschriebenen Produkte
Active – Active System den folgenden Richtlinien entsprechen:
− Richtlinie des Rates 98/37/CE und folgende Änderungen.
− Richtlinie zur elektromagnetischen Verträglichkeit 89/336
und folgende Änderungen.
− Niederspannungsrichtlinie 73/23 und folgende Änderungen.
CONFORMITEITVERKLARING
De firma DAB PUMPS s.p.a - Via Marco Polo, 14 - Mestrino - PD -
ITALY – verklaart onder eigen verantwoordelijkheid dat de eerder
genoemde Active – Active System producten overeenkomen met:
− Richtlijn van de Raad n° 98/37/CE en latere wijzigingen.
− Richtlijn Elektromagnetische Compatibiliteit 89/336
en latere wijzigingen.
− Richtlijn Laagspanning 73/23 en latere wijzigingen.
DECLARACIÓN DE CONFORMIDAD
La empresa DAB PUMPS s.p.a - Via Marco Polo, 14 - Mestrino - PD -
ITALY – bajo su propia y exclusiva responsabilidad declara que los
productos Active – Active System reseñados anteriormente cumplen:
− La Directiva del Consejo n° 98/37/CE y modificaciones siguientes.
− La Directiva de la Compatibilidad electromagnética 89/336
y modificaciones siguientes.
− La Directiva Baja Tensión 73/23 y modificaciones siguientes.
FÖRSÄKRAN OM CE-ÖVERENSSTÄMMELSE
Företaget DAB PUMPS s.p.a - Via Marco Polo 14 - Mestrino (PD) - ITALIEN
- försäkrar härmed att ovannämnda produkter Active - Active System är i
överensstämmelse med:
− Rådets direktiv , nr. 98/37/CE, och efterföljande ändringar.
− Direktivet om elektromagnetisk kompatibilitet 89/336/EEG
och efterföljande ändringar.
− Lågspänningsdirektivet 73/23/EEG och efterföljande ändringar.
∆ΗΛΩΣΗ ΣΥΜΜΟΡΦΩΣΗΣ
Ηεταιρεία DAB PUMPS s.p.a. - Via Marco Polo, 14 - Mestrino - PD –
ΙΤΑΛΙΑ , δηλώνει υπεύθυνα πως τα προϊόντα Active – Active System, που
περιγράφονται παραπάνω, εναρµονίζονται µε:
− Την οδηγία n° 98/37/ΕΟΚ και µετέπειτα τροποποιήσεις.
− Την οδηγία περί µαγνητικής συµβατότητας 89/336/ΕΟΚ και µετέπειτα
τροποποιήσεις.
− Την οδηγία περί χαµηλής τάσης 73/23/ΕΟΚ και µετέπειτα
τροποποιήσεις.
UYGUNLUK BEYANNAMESİ
Via Marco Polo, 14 - Mestrino - PD - İTALYA adresinde yerleşik DAB
PUMPS s.p.a - Firması
sadece kendi sorumluluğu altında, yukarıda listelenmişActive - Active
System ürünlerinin aşağıdaki yönetmeliklere uygun olduğunu beyan
etmektedir:
− 98/37/CE sayılıKonsey Yönergesi ve daha sonraki değişiklikler.
− 89/336 sayılıelektromanyetik Uygunluk Yönergesi ve daha sonraki
değişiklikler.
− 73/23 sayılıAlçak Gerilim Yönergesi ve daha sonraki değişiklikler.
ЗАЯВЛЕНИЕ ОСООТВЕТСТВИИ
Фирма DAB PUMPS s.p.a. – Via Marco Polo, 14 Mestrino (PD) - ИТАЛИЯ -
под собственную ответственность заявляет, что вышеуказанные изделия
Active – Active System соответствуют:
− Директиве Европейского Совета n° 98/37/CE ипоследующим
изменениям.
− Директиве по Электромагнитной совместимости 89/336 и
последующие изменения.
− Директиве по Низкому напряжению 73/23 ипоследующие
изменения.
DECLARAŢIE DE CONFORMITATE
Întrepriderea DAB PUMPS s.p.a - Via Marco Polo, 14 - Mestrino - PD -
ITALY – declarăpe exlusiva proprie răspundere căprodusele Active –
Active System, enumerate în precedenţă, sunt conforme cu:
− Directiva Consiliului nr. 98/37/CE şi următoarele modificări.
− Directiva referitoare la Compatibilitatea electromagnetică89/336
şi următoarele modificări.
− Directiva de JoasăTensiune 73/23 şi următoarele modificări.
ªwIBi} S¦ZeK
DAB PUMPS s.p.a ªyZc{A
Via Marco Polo 14 - Mestrino - PD – Italy
B¢K¦{¥»a} LRK TZeK
Active - Active LBOK}{A áDI ªeBU{A
:«{G ªwIBi} ^BwIBa ©Z¥yY}{A ^System
98/37/CE ~vZ ª{¥X{A á¥Bv Z}A¥C -
.£I ªwR{}{A L½¦XlK{¥
336/89 ~vZ ª¦a¦iBp}{A ª¦®BIZ¢y{A ªwIBi}{A á¥Bv -
.£I ªwR{}{A L½¦XlK{A¥
.£I ªwR{}{A L½¦XlK{A¥ 23/73 htU}{A X¢O{A á¥Bv -
Mestrino (PD), 01/04/03
Attilio Conca
Legale Rappresentante
Legal Representative

ENGLISH
19
1. General
1.1 Applications
2. Pumped fluids
3. Technical data
3.1 Electrical data
3.2 Operating conditions
3.3 Description of model properties
4. Functions
4.1 Control panel
4.2 Control panel functions
4.3 Regulating the Start pressure
4.4 Stopping the pump
5. Installation and connection
5.1 Pump installation
5.2 Electrical connections
5.3 Starting
6. Maintenance
6.1 Starting the pump after a long
period of inactivity
6.2 Modifications and spare parts
6.3 Service kit
7. Troubleshooting
8. ACTIVE SYSTEM kit assembly
8.1 Pumps suitable for fitting the
ACTIVE SYSTEM kit
8.2 Instructions for assembly of the
ACTIVE SYSTEM kit
Fig. 14 Changing the electronic card
Fig. 15 Active System kit assembly
Fig. 16 Electronic card connections
Fig. 17 Load loss diagram
Page
19
19
19
19
19
19
20
20
20
21
21
22
22
22
23
23
24
24
24
24
25
26
26
26
27
109
110
111
1. GENERAL
ACTIVE is a compact pressure boosting system
composed of a pump, a motor and a built-in control
unit, which can also be installed outside.
The pump, with the Active system, starts automatically
when there is water consumption and stops when the
request for water ends.
The system is equipped with:
− an easy-to-use control panel,
− a built-in tank with diaphragm which reduces the
number of starts and stops in the event of leaks
from the pipe,
− protection against dry running.
1.1 Applications
Active is used particularly for increasing pressure in
storage tanks and for supplying water from wells:
− in houses,
− in holiday homes,
− in farms,
− in greenhouses and gardens.
The pump can be used for pumping rainwater and
drinking water.
2. PUMPED FLUIDS
The machine has been designed and built for pumping
water, free from explosive substances and solid
particles or fibres, with a density of 1000 kg/m³ and a
kinematic viscosity of 1 mm²/s, and chemically non-
aggressive liquids.
3. TECHNICAL DATA
3.1 Electrical data
- Supply voltage: 1x220-240V -10+6% 50-60Hz
- Max. current: 6.5 A
- Degree of protection: IP 55 Active System
IP 44 Motor
- Insulation class: F
- Power cable: 1.5 mt H05 RN-F
with/without plug
3.2 Operating conditions
- Range of operation:
- Head up – Hmax (m): 0.3 ÷ 8.4 m³/h
page 112
- Liquid temperature: 0 ÷ 35°C domestic use
(EN 60335-2-41)
- Environment temperature: 0 ÷ 40°C
- Storage temperature: -10 ÷ 40°C
- Maximum working pressure: 8 bar (800 Kpa)
- Relative humidity in air: Max. 95%
- Starting pressure: 1.5 ÷ 2.5 bar (settable)
- Connections: 1” GAS / NPT
Read this documentation
Carefully before
Installation.
Installation, electrical connection and commissioning
must be carried out by skilled personnel in
compliance with the general and local safety
regulations in force in the country of installation of
the product. Failure to comply with these instructions
not only causes risk to personal safety and damage
to the equipment, but invalidates every right to
assistance under guarantee.
- Noise level: Directive EC 89/392/EEC

ENGLISH
20
3.3 Description of model properties.
Pump model Active J Active JI Active JC Active E Active EI Active EC
Characteristics Self-priming centrifugal
centrifugal
self-priming centrifugal
Applications with water from an artesian well or
underground tank pressurization for
domestic use
with water from
an artesian well
or underground
tank
pressurization for
domestic use
Limitations suction up to 8 metres water without
dissolved gases suction up to 8 metres water without dissolved gases
Installation
conditions
with foot valve below head with foot valve below head
Particular
characteristics
suitable
for
pumping
water
containing
air
stainless
suitable for
pumping
water
containing
air
hydraulic,
technopolymer
suitable for
pumping water
containing air
silent running
silent running
and stainless ,
suitable for
pumping water
containing air
hydraulic,
technopolymer,
silent running
Advantages
with respect
to traditional
systems
reduced bulk – greater hygiene – pressure stability– adjustable starting pressure
pump blockage in the event of water lack – self-starting in the event of alarm
limitation of the number of starts – protection against excess temperature of hydraulic parts
built-in no-return valve and pressure gauge – possibility of remote alarm signal.
4. FUNCTIONS
4.1 Control panel
ACTIVE is managed by a control panel which offers:
− the possibility of checking the pump operating status by means of warning lights:
Green ON - Red ALARM (Fig.1)
− the possibility of setting the Start pressure (Fig.2)
Control panel– Fig. 1
green red

ENGLISH
21
4.2 Control panel functions
GREEN WARNING LIGHT ON
− System live or correct operation.
GREEN WARNING LIGHT ON
RED WARNING LIGHT BLINKING
− No water: the pump will perform a series of
automatic restarts.
− Overheating of the motor.
− Blockage of the pump / motor.
GREEN WARNING LIGHT ON
RED WARNING LIGHT ON
− Protection against excess temperature of hydraulic
parts.
There is the possibility of remote signalling of the alarm signal; in fact, on the electronic card, Active
has two male faston outlets ( 4.7 mm ) to allow the connection.
(see fig. 14 on page 27)
Contact characteristics: 24V - 5A – normally open (N.O.)
4.3 Regulating the Start pressure.
To regulate the Start pressure, unscrew the protective cap and turn the green trimmer knob. The pressure may
be set at a minimum of 1.5 bar or a maximum of 2.5 bar. (Fig.2)
START PRESSURE REGULATION
FROM 1.5 TO 2.5 bar
Fig. 2

ENGLISH
22
4.4 Stopping the pump
The pump has a built-in electronic protection function
which allows it to stop in the event of:
− dry running,
− overheating,
− motor overload,
− blockage of the pump / motor.
After stopping in this way, the pump restarts
automatically, making 3 attempts of 3 minutes each,
with pauses of 10 seconds.
The starting attempts will be repeated, in the event of
a negative result:
− after 1 hour : 1 attempt of 3 minutes,
− after 4 hours : 1 attempt of 3 minutes,
− every 15 hours : 1 attempt of 3 minutes.
To perform manual resetting of the pump you must
supply power to it again, disconnecting the voltage for
a few seconds.
5. INSTALLATION AND CONNECTION
5.1 Pump installation
− The electropump must be installed in a well
ventilated place, protected from inclement weather
and with an environment temperature no higher
than 40°C.
− A solid anchoring of the pump to its support base
helps absorb any vibrations created by pump
operation.
− Always fit the pump on a base with the intake
opening horizontal and the delivery opening
vertical.
− The pump must be installed exclusively in
horizontal position (Fig.3):
− To avoid transmitting vibrations to the system, after
delivery it is recommended to use the flexible pipe
that is supplied inside the packing. (Fig.4).
− Do not allow the metal pipes to weigh down on the
pump openings, transmitting excessive strain, so as
not to create deformations or breakages. Anchor the
pipes separately if possible.
− The suction pipe must be as short as possible. For
suction depths of more than 4 metres or with long
horizontal stretches, it is recommended to use a
suction pipe with a diameter larger than that of the
suction opening of the electropump.
− To avoid the formation of air pockets in the suction
pipe, ensure a slight positive tilt of the same towards
the electropump.
− If it is not possible to use the flexible pipe to make
the connection, use only Teflon tape. (Fig.5).
− For any maintenance jobs it is recommended:
• to fit an interception valve along the pipe, close
to the pump (Fig.6),
• to use a straight length of pipe, after delivery, for
lifting the cover of the Active system, in the event
of inspection (Fig.6).
Fig. 3
Fig. 6
Fig. 4
Fig. 5

ENGLISH
23
− At suction from a well it is indispensable to
install a foot valve complete with filter (Fig.7).
− The pump is supplied with fittings:
1” GAS for 50Hz versions
1” NPT for 60Hz versions (on request also GAS)
If a fitting is also used on suction, it must be of the
non deformable type (Fig.8)
5.2 Electrical connections
ATTENTION!!
ALWAYS OBSERVE THE SAFETY
REGULATIONS!!
Electrical installation must be carried out by an
authorised, skilled electrician who assumes all
responsibility.
THE SYSTEM MUST BE
CORRECTLY AND SAFELY
EARTHED!!
− Ensure that the mains voltage is the same as that
shown on the motor data plate.
− The correct operating voltage and frequency are
indicated on the pump data plate.
Never make any connection on the terminal
card if the electric power supply has not
been deactivated for at least 5 minutes.
5.3 Starting
DO NOT START THE PUMP WITHOUT
HAVING COMPLETELY FILLED IT
WITH FLUID.
Before starting, check that the pump has been regularly
primed, filling it completely with clean water through the
hole provided, after having removed the filling cap,
located on the pump body. The filling cap must then be
accurately screwed back on (Fig.9).
− Connect the power cable to the mains.
− When the cable is connected, the red warning light
and the green one on the control panel light up
simultaneously for 3 seconds (Fig.10).
The remote alarm signal will also be activated for 3
seconds, if present.
Fig. 10
Fig. 8
Foot valve
Fig. 7
H20
Fig. 9

ENGLISH
24
− The pump starts automatically, keeping only the
green led lit (Fig.11).
After starting, the pump will begin to prime and will
operate according to the set parameters.
If priming has not been completed within 5 minutes,
the pump will stop automatically and will make 3
attempts to start of about 3 minutes each, with pauses
of 10 seconds.
The starting attempts will be repeated, in the event of
a negative result:
− after 1 hour : 1 attempt of 3 minutes,
− after 4 hours : 1 attempt of 3 minutes,
− every 15 hours : 1 attempt of 3 minutes.
To perform manual resetting of the pump you must
supply power to it again, disconnecting the voltage for
a few seconds.
6. MAINTENANCE
− In normal operating conditions the electropump
does not require any kind of maintenance.
− However, it may be necessary to clean the
hydraulic parts if you notice a certain reduction of
its characteristics.
− The electropump can only be dismantled by
specialised, skilled personnel in possession of
the qualifications required by the specific
regulations.
− In any case all repair and maintenance jobs must
be carried out only after having disconnected
the pump from the power mains.
Never touch the electronic components of
the pump if the power has not been turned
off for at least 5 minutes.
− If there is the risk of damage caused by frost, drain
the pump through the drainage cap (Fig.12).
The pump must be filled again before starting. Fig. 9.
6.1 Starting the pump after a long period of
inactivity
Using a screwdriver, inserted in the hole in the centre of
the fan cover, it is possible to free the rotor if the pump
has been still for a long time.
If the pump has been drained, it must be filled with fluid
before starting. Fig. 9
6.2 Modifications and spare parts
Any modification not authorised beforehand relieves the
manufacturer of all responsibility. All the spare parts
must be authentic and all the accessories must be
authorised by the manufacturer.
6.3 Service Kit
The following service kits are available:
− mechanical seal,
− electronic card,
− hydraulic components of the pump.
To change the electronic card CAREFULLY follow the
diagram on page 27 Fig. 14.
If the power cable of this appliance is damaged, it must be repaired by specialised
personnel to prevent all risks.
ATTENTION: if pumps for outdoor use are installed, supply cables type H07 RN-F, complete with plug
(EN 60335-2-41).
For power cables without a plug, provide a cut-out device for the power mains (e.g. magnetothermal device)
with separation contacts of at least 3 mm for each pole.
Fig. 11
Fig. 12

ENGLISH
25
7. TROUBLESHOOTING.
Fault Check (possible causes) Remedies
− Insufficient water. Check the suction pipe.
− Overheating due to the high
temperature of the fluid (above
+40°C).
Feed the pump with cold water.
− Overheating due to blocking of
the pump. Contact the pump supplier.
− Voltage too low or too high. Check the voltage of the power
supply
− No electric power supply. Connect to the power mains.
− No water consumption. Turn on a tap. Check that the height
between the highest point of the
delivery pipe and the pump is not
greater than 25 metres.
On the control panel, check the
regulation of the starting pressure
(1.5 ÷ 2.5 bar).
The pump does not start.
− The pump is in alarm status. The pump resets automatically with
self-starts.
It is possible to reset the pump by
feeding it again, disconnecting the
voltage for a few seconds.
− The existing pipe has a leak or is
faulty. Repair the pipe.
The pump does not stop.
− The check valve is blocked or
missing. Clean the valve, dismantling the
system.
− Dry running. Check the suction pipe.
− Overheating due to the high
temperature of the fluid (above
+40°C).
Feed the pump with cold water.
− Overheating due to:
• High environment temperature
(> 45°C).
• Motor overload.
• Blockage of the pump/motor.
Contact the pump supplier.
The pump stops during operation.
− Voltage too low. Check the power supply.
The pump starts and stops
frequently. − The suction pipe is leaking or
there is air in the water. Check the suction pipe.
The pump transmits electric
discharges. − Faulty earthing. Connect the earth system according to the local regulations.
The pump starts when there is no
request for water. − Faulty check valve or leaks from
the existing pipe. Clean the valve or replace it with a
new one.
If the pump does not start when the faults have been repaired, contact the pump supplier.

ENGLISH
26
8. ACTIVE SYSTEM KIT ASSEMBLY.
The ACTIVE SYSTEM Kit can be fitted exclusively on new Dab products,
single-phase, with voltage 220/240 V – 50/60 Hz.
No kind of adaptation or modification can be made to the Kit to allow it to be
fitted on the pump.
Otherwise, tampering will invalidate every right to assistance under guarantee.
8.1 Pumps suitable for fitting the ACTIVE SYSTEM Kit .
JET JETINOX JETCOM *EURO *EUROINOX *EUROCOM
Jet 62 M Jetinox 62 M Jetcom 62 M Euro 25/30 M Euroinox 25/30 M Eurocom 25/30 M
Jet 82 M Jetinox 82 M Jetcom 82 M Euro 30/30 M Euroinox 30/30 M Eurocom 30/30 M
Jet 92 M Jetinox 92 M Jetcom 92 M Euro 40/30 M Euroinox 40/30 M Eurocom 30/50 M
Jet 102 M Jetinox 102 M Jetcom 102 M Euro 30/50 M Euroinox 30/50 M Eurocom 40/50 M
Jet 112 M Jetinox 112 M Euro 40/50 M Euroinox 40/50 M
Jet 132 M Jetinox 132 M Jetcom 132 M Euro 50/50 M Euroinox 50/50 M
Euro 25/80 M Euroinox 25/80 M Eurocom 25/80 M
Euro 30/80 M Euroinox 30/80 M Eurocom 30/80 M
Euro 40/80 M Euroinox 40/80 M
*Only for Euro/Euroinox/Eurocom Pumps
produced as from MAY 2003
8.2. Instructions for assembly of the ACTIVE SYSTEM Kit .
To assemble the ACTIVE SYSTEM Kit CAREFULLY follow the instructions on page 109 fig.15.
It is recommended to recover the data plate of the pump on which the Active System kit is fitted.
It is also important to mark the name of the pump on the data plate of the Active System kit in the reserved
space “PUMP TYPE”, as indicated in figure 13.
Fig. 13
Cod.
thtt
MADE IN ITALY
TF 40
A
max IP
PN max bar
PUMP TYPE
............................
JET 62

ENGLISH
27
Changing the electronic card
Fig. 14
1
2
It is recommended to use a straight length of pipe,
after delivery, for lifting the cover of the Active system,
in the event of inspection.
The operations, described below, for changing the electronic card must be carried out
exclusively by specialised, qualified personnel:
− Reduce the system pressure (it is recommended to close the valve of the system, located fo
r
this purpose on delivery, near the pump ).
− Disconnect the electric connectors of the card.
− Unscrew the 4 screws of the card, keeping it pressed.
− Turn the card towards the outside.
− Pull the card upwards, keeping it tilted.
− Pay attention to the OR of the pressure probe!!!
(pressure probe: card connecting tube with a hydraulic body )
Male Faston outlets for
remote alarm signal

109
Montaggio Kit Active System – Montage Kit Active System – Active System Kit Assembly
Montage des Kits Active System – Montage Active System-kit – Montaje del Kit Active System
Installation av Active System sats – Τοποθέτηση Kit Active System – Active Sistem takımının montajı
Монтаж комплекта ACTIVE SYSTEM – Montajul Kit-ului Active System – ACTIVE SYSTEM ª®¦¢{A J¦yZK
Fig.15 – Abb.15 – Afb.15 – Εικ.15 – Res.15 – Рис. 15 – 15 ©Z¥e
1
2
I Avvitare fino alla battuta
F Visser à fond
GB Screw fully down
D Bis zum Anschlag einschrauben
NL Vastschroeven tot aanslag
E Atornillar a fondo
S Skruva ända till ändläget
GR Βιδώστε τέρµα
T Çıkıntıya kadar vidalayınız
RU Закрутить до упора
RM Înşurubaţi pânăla închiderea completă
n
ªIZg{{ |¥e¥{A «KR Xc{A
JETINOX
JETCOM
EUROINOX
EUROCOM
JET
EURO
P2 ≤0,55 Kw
Orin
g

110
Collegamenti scheda elettronica – Connexions carte électronique – Electronic card connections
Anschlüsse der Elektronikkarte – Aansluitingen elektronenkaart – Conexiones de la tarjeta electrónica
Kretskortets anslutningar – Συνδεσµολογία ηλεκτρονικής κάρτας – Elektronik kart bağlantıları
Соединения электронной платы – Legături fişă electronică– ª¦¥ZKy{ÂA ªvBiI{A L¼Be¦G
Fig.16 – Abb.16 – Afb.16 – Εικ.16 – Res.16 – Рис. 16 – 16 ©Z¥e
I CONNESSIONE NORMALE
F CONNEXION NORMALE
GB NORMAL CONNECTION
D NORMALER ANSCHLUSS
NL NORMALE VERBINDING
E CONEXIÓN NORMAL
S NORMAL ANSLUTNING
GR ΚΑΝΟΝΙΚΗ ΣΥΝ∆ΕΣΜΟΛΟΓΙΑ
T NORMAL BAĞLANTI
RU СТАНДАРТНОЕ СОЕДИНЕНИЕ
RM CONEXIUNE NORMALĂ
n
¨XBk |Be¦G
I CONNESSIONE ACTIVE
F CONNEXION ACTIVE
GB ACTIVE CONNECTION
D ACTIVE-ANSCHLUSS
NL ACTIVE-VERBINDING
E CONEXIÓN ACTIVE
S ANSLUTNING AV ACTIVE
GR ΣΥΝ∆ΕΣΜΟΛΟΓΙΑ ACTIVE
T ACTIVE BAĞLANTISI
RU СОЕДИНЕНИЕ ACTIVE
RM CONEXIUNE ACTIVE
n
ACTIVE |Be¦G
CAPACITO
R
CONDENSATORE
CAPACITO
R
CONDENSATORE
BLU - BLUE
ROSSO - RED
NERO - BLAC
K
BLU - BLUE
ROSSO - RED
NERO - BLAC
K
BLU - BLUE
BLU - BLUE
GRIGIO - GREY NERO - BLAC
K
GIALLOVERDE-YELLOWGREEN

111
Diagramma perdite di carico – Diagramme pertes de charge – Load loss diagram
Diagramm der Energiegefälle – Diagram ladingverlies – Diagrama pérdidas de carga
Diagram över tryckförluster – ∆ιάγραµµαµεαπώλειες φορτίου – Yük kaybıdiyagramı
Кривая потери нагрузки – Diagrama pierderi de încărcătură– |}R{A áAXwt{ §i¦iUK ~aZ
Fig.17 – Abb.17 – Afb.17 – Εικ.17 – Res.17 – Рис. 17 – 17 ©Z¥e
ACTIVE Hydraulic Losses
0
1
2
3
4
5
6
7
0 20 40 60 80 100 120 140 160
Q (l/min)
H (m)
-0,02
0,08
0,18
0,28
0,38
0,48
0,58
0,68
bar

112
Prevalenza / Hauteur d'élévation / Head up
Förderhöhe / Overwicht / Prevalencia
Maximal pumphöjd / Manometrik yükseklik
Напор / x¥tK{A
Modello / Modèle /Model
Modell / Model
Modelo / Modell / Model
Модель / QY¥}
Hmax (m) 2 poles
50 Hz Hmax (m) 2 poles 60 Hz
ACTIVE J 62 42 41
ACTIVE J 82 47 44.5
ACTIVE J 102 53.8 53
ACTIVE J 112 60 60
ACTIVE J 92 36.2 35
ACTIVE J 132 48 48
ACTIVE JI 62 42 41
ACTIVE JI 82 47 43
ACTIVE JI 102 53.8 50
ACTIVE JI 112 61 60
ACTIVE JI 92 36.5 35
ACTIVE JI 132 48.3 47.5
ACTIVE JC 62 42 41
ACTIVE JC 82 47 44
ACTIVE JC 102 53.8 53.8
ACTIVE JC 92 36.5 35
ACTIVE JC 132 48.3 48.3
ACTIVE E 25/30 – 25/306 34.5 35.9
ACTIVE E 30/30 – 30/306 46 48.2
ACTIVE E 40/30 – 40/306 57 58.8
ACTIVE E 30/50 – 30/506 42.5 38.8
ACTIVE E 40/50 – 40/506 57.5 54
ACTIVE E 50/50 – 50/506 72 66.1
ACTIVE E 25/80 – 25/806 34 35.8
ACTIVE E 30/80 – 30/806 46.75 49.5
ACTIVE E 40/80 – 40/806 58.6 62
ACTIVE EC 25/30 – 25/306 34 36
ACTIVE EC 30/30 – 30/306 46 48
ACTIVE EC 30/50 – 30/506 42 38.8
ACTIVE EC 40/50 – 40/506 58 53.8
ACTIVE EC 25/80 – 25/806 34 35.7
ACTIVE EC 30/80 – 30/806 46.75 49.2
ACTIVE EI 25/30 – 25/306 34.5 35.9
ACTIVE EI 30/30 – 30/306 46 49
ACTIVE EI 40/30 – 40/306 54 58.8
ACTIVE EI 30/50 – 30/506 40 39
ACTIVE EI 40/50 – 40/506 57.7 54
ACTIVE EI 50/50 – 50/506 68 66
ACTIVE EI 25/80 – 25/806 34 37
ACTIVE EI 30/80 – 30/806 47 50
ACTIVE EI 40/80 – 40/806 59 59

113

114

05/06 cod.0013.600.17