Dabir Surfaces C2-100 Series User manual

1
Corporate Headquarters, Sales & Manufacturing:
Dabir Surfaces, Inc., 7447 West Wilson Ave., Harwood Heights, IL 60706, USA, www.dabir-surfaces.com
Sales Inquiries: [e-mail], Tel: [phone]
Technical Support: [e-mail], Tel: [phone]
PATENT: www.dabir-surfaces.com/patents
DOC# R02-0006-00014-DA
®
Quick Set-Up Guide (C2-100X Models ONLY)
Important Before You Start: THIS IS A “QUICK SET-UP” GUIDE ONLY
Please refer to the Dabir Operaon / Service Technical Manual for full set-up and usage instrucons. Failure to carefully read and
follow all instrucons and safety informaon may result in decreased product performance or injury.
Controller Pre-Assembly
1. Remove components from their individual packaging containers.
2. Place Controller on a at, stable surface, away from any edges to
prevent fall damage.
3. Insert latching Power Cord as shown.
4. Conrm proper inseron with a slight pull.
5. If applicable, assemble Controller mounng accessories per the
separately supplied user instrucons. (RECOMMENDED)
STEP 3: Insert Power Cord
System Installaon - Controller
6. Place Controller in a safe, stable locaon near a wall power outlet
and at an appropriate distance from the paent care area.
7. Route the Power Cord such that it does NOT present a trip hazard.
8. Plug the Power Cord into the AC wall receptacle or other power
source with appropriate currents and protecve earth ground.
STEP 8: Plug-in Power Cord
System Installaon - Surfaces
9. Place Dabir Surface onto at maress with “THIS SIDE UP” facing up
(gray side down) and secure oponal corner straps when applicable.
(Surface should lay at when properly installed.) Hose exit orientaon
is oponal depending on the desired set-up.
10. Place facility supplied linen and inconnence pad(s) over the top of
the Dabir Surface and tuck edges underneath the maress. Avoid
wrinkles whenever possible to opmize Dabir performance and
paent comfort.
STEP 9: Place Dabir Surface onto at Maress
WARNINGS / CAUTIONS:
• Surfaces are intended to be used ABOVE an underlying bed
maress with good pressure redistribuon properes over
the full paent contact area.
• Always place the Surface ABOVE the maress and cover it
with a bed linen. (Surfaces are NOT intended to be used in
direct contact with the paent’s skin.)
• It is the responsibility of the user to secure and protect
against paent movement and/or falls.
• It is the responsibility of the user to properly clean and disin-
fect the System prior to paent use. (See Secon 7 Cleaning
Procedure of the Dabir Operaon / Service Technical Manual
for a list of approved / unapproved cleaners.)
NOTE: Controller User Interface may vary from instrucons.

2
Corporate Headquarters, Sales & Manufacturing:
Dabir Surfaces, Inc., 7447 West Wilson Ave., Harwood Heights, IL 60706, USA, www.dabir-surfaces.com
Sales Inquiries: [e-mail], Tel: [phone]
Technical Support: [e-mail], Tel: [phone]
PATENT: www.dabir-surfaces.com/patents
DOC# R02-0006-00014-DA
System Installaon - Surface Connecons
11. Insert Surface connector as shown.
12. Listen for an inseron “CLICK” to conrm proper connecon.
NOTE: Therapy will start automacally if powered “ON”.
Surface
Connector
Controller Operaon: “ON”, “OFF” and “PAUSE” Mode
13. POWER “ON”: Touch and hold the “POWER” key unl the “START-UP”
screen appears. Therapy will automacally begin if a Surface is connected.
System Starting
SW vXXX.X.XX
Geng familiar with the Controller User Interface:
75%
933
HRS
933
HRS
MICROPRESSURE
933
HRS
HIGH
LOW
CYCLE
SPEED
SURFACE
"MICROCLIMATE"
Feature NOT available
at this me
"MICROPRESSURE"
"LOW" and "HIGH"
alternang cycle speeds
"POWER"
"ON", "OFF" and "PAUSE"
"SELECT"
"MENU" conrmaon and
"KEY LOCK" mode
STEPS 11 & 12: Connector Inseron
WARNINGS / CAUTIONS:
• Therapy is NOT provided unless the Controller is powered “ON” and the Surface is acvely cycling.
Quick Set-Up Guide - Connued
16. “KEY LOCK” MODE “ON” / “OFF”: Touch and hold the "SELECT" key
for 4 seconds to “LOCK” display. (Yellow lock symbol will appear.)
Touch and hold the “SELECT” key for another 4 seconds to
“UNLOCK” the display. (Yellow lock symbol will disappear.)
RESUME
RESUME IN XX:XX MINUTES
SYSTEM PAUSED
14. POWER “OFF”: Touch and hold the “POWER”
key unl the “OPTIONS” Menu appears. Select
“SHUTDOWN” by touching “POWER” key for 2
seconds.
15. “PAUSE” MODE: Touch and hold the “POWER”
key unl the “OPTIONS” screen appears, then
select “PAUSE” to temporarily stop therapy.
(Default is 30 minutes.) Select “RESUME” at
anyme to immediately resume therapy.
STEP 13: Power Controller “ON”
SELECT OPTION
SHUTDOWN
RESUME
PAUSE
(Hold 2 seconds)
NOTE: For C2-1002 Models, the User Interface has been simplied. To change cycle speed, press the “DOWN” key