Dacor DRT366 Technical manual

PLANNING
GUIDE
4.14
Specications subject to change without notice. Phone: [phone]www.Dacor.com
A
30” and 36” Wide, Distinctive Series
Slide-in Gas Cooktops
DRT304S, DRT366S
ELECTRIC CIRCUIT REQUIREMENTS
Circuit Required Total Connected Load
120 Vac 60Hz, 15 Amp. (3 wire) 1.0 Amp @ 120 Vac, 60 Hz.
GAS SUPPLY PRESSURE REQUIREMENTS*
Gas Type Manifold Pressure Minimum Gas Supply
Pressure
Natural Gas 5” Water Column 6” Water Column
Propane (LP) 10” Water Column 11” Water Column
* Maximum gas supply pressure for all models is 1/2 p.s.i.
Installation of a non-combustible material* (up to the hood) or a backsplash
is always recommended, and mandatory if the distance to the back
wall from the cooktop is less than 2 1/2” (Figure 2). When installing a
backguard, use only Dacor model numbers AEB3009 (DRT304S), AEB3609
or AEB3612 (DRT366S).
SIDE VIEW WITHOUT BACKGUARD
SIDE VIEW WITHOUT BACKGUARD
SIDE VIEW
Product Dimensions
Electrical and Gas Supply Requirements
Cabinet and Countertop Layout
COOKTOP WIDTH (A)
DRT304S 29 7/8” (75.9 cm)
DRT366S 35 7/8” (91.1 cm)
Product tolerances:
±1/16” (±1.6 mm)
unless otherwise noted
WARNING
• Observe all governing codes and ordinances during planning
and installation. Contact your local building department for
further information.
• This appliance must be installed in accordance with the
accompanying installation instructions.
Document # PG04-003 Revised 02/03/11 Page 1/4
4” (10.2 cm) 5/8” min.
(1.6 cm)
7 3/4”
(19.7 cm)
Trim:
1/2”
(1.3 cm)
thick
25 7/8” (65.7 cm)
1 5/8” (4.1 cm) cooking surface
height (grate level) above
countertop
3/4” gas inlet, connects to regulator from
bottom or rear of unit, end is recessed
2” (5.1 cm) from chassis bottom
28 1/8” (71.4 cm)
Power cord
32” (81.3 cm) long
Combustible
rear wall
Backguard mandatory if
gap from back of cooktop
to combustible wall is less
than 2 1/2”
Combustible
rear wall
2 1/2” (6.4 cm) min. to
combustible rear wall

PLANNING
GUIDE
4.15
Specications subject to change without notice. Phone: [phone]www.Dacor.com
See note 2
2See Cabinet/Countertop Dimensions - Top View
3Not applicable for cabinets more than a horizontal
distance of 10” (25.4 cm) from the edge of the cooktop.
1Vertical to combustible surface from cooktop grate level;
if installing an overhead vent hood, also check the hood
specifications for minimum required clearances.
C
13” (33.0 cm)
max.3
Top of
finished
counter
18” (45.7 cm)
min.1, 3
30” (76.2 cm)
min.1Cutout for
utility access
Hood
Recommended
gas and electrical
service location,
consult local code
B
10” (25.4 cm) to
combustible side
wall min. both sides 1/2” (1.3 cm)
overhang,
both sides
1 1/2” (3.8 cm)
typical countertop
thickness
7 3/4”
(19.7 cm)
36” (91.4 cm)
typical
Cooktop platform
1” (2.5 cm) min.
thickness
Model No. B C
DRT304S 30” (76.2 cm) 30” (76.2 cm)*
36” (91.4 cm)**
DRT366S 36” (91.4 cm) 36” (91.4 cm)*
42” (106.7 cm)**
* Minimum ** Recommended
Cabinet tolerances: +1/16”, -0 (+1.6 mm, -0)
unless otherwise noted.
CABINET/COUNTERTOP DIMENSIONS - FRONT VIEW
CABINET/COUNTERTOP DIMENSIONS -
ISO VIEW
Continued. on following page...
Cabinet and Countertop Layout (Continued)
DRT304S, DRT366S
Document # PG04-003 Revised 02/03/11 Page 2/4
NOTE: Model DRT304S is not approved for installation
with a raised vent.
30” and 36” Wide, Distinctive Series
Slide-in Gas Cooktops

PLANNING
GUIDE
4.16
Specications subject to change without notice. Phone: [phone]www.Dacor.com
DRT304S, DRT366S
CABINET/COUNTERTOP CUTOUT DIMENSIONS WITHOUT RAISED VENT - TOP VIEW
Model No. B - Cutout Width D E
DRT304S 30” (76.2 cm) 13 3/8” (34.0 cm) 10 1/8” (25.7 cm)
DRT366S 36” (91.4 cm) 16 5/8” (42.2 cm) 11 3/16” (28.4 cm)
Cutout tolerances: +1/16” (+1.6 mm), -0, unless otherwise stated
Document # PG04-003 Revised 02/03/11 Page 3/4
Cabinet and Countertop Layout (Continued)
Non-combustible
rear wall, rear of
mounting platform
10” (25.4 cm) min.
to combustible wall
above countertop,
both sides
Cabinet face
below countertop
overhang
Increase countertop and overhang
additional 2 1/2” (6.4 cm) min. for
combustible rear wall above
countertop
3/8” (1.3 cm)
countertop overhang
Hole 1/2” dia. (1.3 cm),
2 places, through platform
for hold down bolts
Gas/electrical utility cut-out in right rear corner of
mounting platform 8” W X 6” D (20.3 cm X 15.2 cm),
if gas and electrical are routed through bottom
1/2” (1.3 cm)
countertop
overhang
1” thick mounting platform min.
Countertop
Countertop
1/2” (1.3 cm)
countertop
overhang
2” (5.1 cm)
1” (2.5 cm)
E
24 5/8”
(62.5 cm)
D D
B
C
L
Gas connection and power cord may be
routed through bottom or back of chassis
Gas and electrical connections at
right rear section of chassis
30” and 36” Wide, Distinctive Series
Slide-in Gas Cooktops

PLANNING
GUIDE
4.17
Specications subject to change without notice. Phone: [phone]www.Dacor.com
Stiffener
Cabinet face
Control panel
Countertop
Use Dacor raised
vent, model
ERV3615 only IMPORTANT: See raised vent
installation instructions for
duct system layout/planning
DRT366 cooktop
3/8” min. (1.0 cm)
space behind
raised vent
chassis to clear
stiffener
3/8” min. (1.0 cm)
flat countertop
overhang required
behind cutout
Minimum
countertop
height:
30 1/4"
(76.8 cm)
28 5/16” (71.9 cm)
Non combustible rear
wall recommended 10” (2.5 cm) min. to
combustible wall
above countertop,
both sides
Cabinet face
below countertop
overhang
3/8” (1.0 cm) min.
countertop overhang
2 5/8”
(6.7 cm)
Hole 1/2” dia. (1.3 cm),
2 places, through platform
for hold down bolts
1/2” (1.3 cm)
countertop
overhang
1” (2.5 cm) thick mounting platform min.
Open to below to allow for raised
vent, gas and electrical connections
Countertop
Countertop
1/2” (1.3 cm)
countertop
overhang
2” (5.1 cm)
1” (2.5 cm)
15”
(38.1 cm)
24 1/2”
(62.2 cm)
D
E
D
F
B
C
L
CABINET/COUNTERTOP CUTOUT
DIMENSIONS WITH RAISED
VENT - TOP VIEW
CABINET/COUNTERTOP CUTOUT
DIMENSIONS WITH RAISED
VENT - SIDE VIEW
Model
No.*
B - Cutout
Width D E F - Raised Vent Cutout
DRT366S 36”
(91.4 cm)
16 5/8”
(42.2 cm)
11 3/16”
(28.4 cm)
33 1/2”
(85.1 cm)
* Model DRT304 is not approved for use with a raised vent.
** Use only raised vent model specified. Raised vent is not
compatible with DRT cooktops having a serial number starting
with letters “SA.”
Cutout tolerances: +1/16” (+1.6 mm), -0, unless otherwise stated
DRT304S, DRT366S
Document # PG04-003 Revised 02/03/11 Page 4/4
Cabinet and Countertop Layout (Continued)
30” and 36” Wide, Distinctive Series
Slide-in Gas Cooktops
NOTE: Gas and electrical connections may only be routed through
the bottom of the cooktop when installed with a raised vent.