Dacor Epicure ESG366 Technical manual

PLANNING
GUIDE
Web: http://www.Dacor.com
Corporate Phone: [phone]
Specifications are subject to change without notice.
See installation instructions for additional details. 4.1
36”, 48” Wide,
Epicure™ Gas Cooktops
ESG366, ESG486
1/2
CABINET DIMENSIONS
Model No.
Electrical
Circuit
Required
Total
Connected
Load Gas Type
Manifold
Pressure
Min. Gas
Supply
pressure
Approximate
Shipping
Weight
ESG366
120 Vac,
60 Hz,15 Amp
0.25 Amps
(0.03 Kw)
Natural 4” Water
Column
5” Water
Column 128 lbs.
ESG366LP Liquid
Propane
10” Water
Column
11” Water
Column
ESG486 Natural 4” Water
Column
5” Water
Column 149 lbs.
ESG486LP Liquid
Propane
10” Water
Column
11” Water
Column
Gas and Electrical Requirements
NOTES:
1. If cabinet storage space is to
be provided directly above the
cooktop, the risk of personal injury
may be reduced by installing a
ventilating hood that projects
horizontally a minimum of 5 inches
(127mm) beyond the face of the
cabinets.
2. Access to the underside of the
cooktop, the electrical connection,
the gas shut-off valve and the
pressure regulator must be
provided for inspection and
service.
Plan the installation so that the electrical
connection, gas shut-off valve, and pressure
regulator are accessible from the front of the
cabinet, and that all of the minimum dimensions
are provided. Dimensions apply to all models
unless otherwise noted. Locate the electrical
supply box within reach of the included 48 inch
(1219mm) long flexible cord so the connection
is accessible when the cooktop is in place.
Hood
ESG366: 42" (1067mm) Recommended
36" (914mm) Minimum
ESG486: 54" (1372mm) Recommended
48" (1219mm) Minimum
10" (254mm)
Min. to
combustible side
wall, both sides
See Page 4
1 1/2" (38mm)
Typical Countertop
18"
(457mm)
30" (762mm)
Minimum
36"
(914mm)
28 1/4"
(717mm)
7 3/4"
(197mm)
Utilities
Location
C
L
6"
(152mm)
ESG366:
24" (610mm)
ESG486: 30" (762mm)
10"
(254mm)
15 1/2"
(393mm)
See Page 4
NOTES:
1. Factory installed liquid propane (LP) special
ordered.
2. Cooktop is supplied with a 48” (1219mm) power
cord, with a three prong grounded plug.
3. Utilities are located in the right rear corner of the
cooktop.
4. Utlities may be located in the right rear corner of
the cabinet below the cooktop. (Recommended)
5. See the Combination Installation (CI) Section if
installing with a downdraft, or warming oven.
Revised
02/29/08

PLANNING
GUIDE
Web: http://www.Dacor.com
Corporate Phone: [phone]
Specifications are subject to change without notice.
See installation instructions for additional details. 4.2
36”, 48” Wide,
Epicure™ Gas Cooktops
ESG366, ESG486
2/2
22"
(559mm)
3 1/2"
(89mm)
1 1/8"
(286mm)
5/8"
(16mm)
ESG366: 35 7/8" (911mm)
ESG486: 47 7/8" (1216mm)
ESG366: 34 3/4" (883mm)
ESG486: 46" (1168mm)
Non-combustible
rear wall
C
L
22" (559mm)
3" (76mm) Typical
ESG366: 5/8" (16mm)
ESG486: 1” (25mm)
ESG366:
17 3/8" (441mm)
ESG486:
23" (584mm)
ESG366:
17 3/8" (441mm)
ESG486:
23" (584mm)
ESG366:
36" (914mm)
ESG486:
48" (1219mm)
Countertop
COUNTERTOP PREPARATION
NON-COMBUSTIBLE REAR WALL
Cutout for gas and electrical
locations
C
L
Non-combustible
rear wall
C
L
Drill two 1/2" (13mm) holes through
support shelf for cooktop mounting bolts
ESG366
16 5/8" (422mm)
ESG486
20 13/16" (529mm)
ESG366
16 5/8" (422mm)
ESG486
20 13/16" (529mm)
8" (203mm)
6" (152mm)
24" (610mm)
12 9/16"
(319mm)
BASE CABINET PREPARATION
NON-COMBUSTIBLE REAR WALL
TOP VIEW
Combustible
rear wall
material
26 1/2" (673mm)
To bullnose
27" (686mm)
To knob
7 3/4" (197mm)
Top of
finished
counter
1" (25mm)
Minimum
Cooktop
platform
2 1/2" (64mm)
Min. to combustible surface
Combustible
rear wall
material
Optional Stainless Steel
Dacor Backsplash
ESG366: AEB3609 or AEB3612
ESG486: AEB4809 or AEB4812
OVERALL DIMENSIONS CLEARANCE
TO COMBUSTIBLE REAR WALL
21 3/8"
(543mm)
28 3/16"
(716mm)
5/8" (16mm)
2 Places ESG366 - 36" (914mm)
ESG486 - 48" (1219mm)
ESG366 -33 7/8" (860mm)
ESG486 - 43 1/2" (1105mm)
3" (76mm)
Backsplash
Max.3/4" (19mm)
1/4" (6mm)
Min. flat ledge
Vertical
non-combustible
surface rear wall
2 13/16"
(71mm)
7/16" (11mm) ESG366
1 5/8” (41mm) ESG486
CUTOUT DIMENSIONS WITH
COUNTERTOP VENT
Revised
02/29/08