Dacor ED24 User manual

Installation Instructions
24-Inch Dishwasher
For usewith models: ED24, ID24, MDH24, MDV24 and PD24
PartNo. 101891 Rev. L

Important Safety Instructions .......................................... 1
Important Information About Safety Instructions .............. 1
Safety Symbols and Labels ............................................. 1
General Safety Precautions ............................................. 2
Design Specifications ....................................................... 3
Product Specifications ...................................................... 3
Preparing for Installation .................................................. 4
Preparing the Location ..................................................... 4
Power Supply Preparation ............................................... 5
Plumbing Preparation ....................................................... 5
Preparing the Drain .......................................................... 5
Installation Instructions .................................................... 6
Verify the Package Contents ............................................ 6
Electrical Connection ....................................................... 7
Plumbing Connections ..................................................... 9
Installing the Unit in the Cabinet ...................................... 9
Drain Line Installation .................................................... 12
Verifying Proper Operation ............................................. 13
Important:
Installer: In the interest of safety and to minimize problems, read these installation instructions completely and carefully
before you begin the installation process. Leave these installation instructions with the customer.
Customer: Keep these installation instructions for future reference and the local electrical inspector's use.
If You Need Help...
If you have questions or problems with installation, contact
your Dacor dealer or the Dacor Customer Service Team.
For repairs to Dacor appliances under warranty call the
Dacor Distinctive Service line. Whenever you call, have the
model and serial number of the appliance ready. The model
and serial number are printed on the product data label.
Dacor Distinctive Service (repairs under warranty only)
Phone: [phone] (U.S.A. and Canada)
Monday -- Friday 6:00 A.M.to 4:00 P.M.Pacific Time
Dacor Customer Service
Phone: [phone] (U.S.A. and Canada)
Monday -- Friday 6:00 A.M.to 5:00 P.M.Pacific Time
Web site: www.Dacor.com
Product Data Label Location
The product data label is located on the left door jamb.
Open the door to expose it.
All specifications are subject to change without notice. Dacor ®assumes no liability for changes to specifications.
© 2007 Dacor, all rights reserved.

Important Information About
Safety Instructions
The Important Safety Instructions and warnings in
these instructions are not meant to cover all possible
problems and conditions that can occur. Use common
sense and caution when installing, maintaining or
operating this or any other appliance.
• Always contact the Dacor Customer Service Team about
problems and conditions that you don't understand. See
Customer Service Information.
Safety Symbols and Labels
Immediate hazards that WILt. result in severe personal
injury Or deathl
WARNING
Hazards Or Unsafe practices that COULD result insevere
personal injury or death.
[_ CAUTION I
Hazards Or Unsafe practices that COULD result in rain0[
personal injury or property damage: I
[_ WARNING I
A qualified technician must complete the installation of this built.in appliance. The owner is responsible tO make sure the I
dishwasher is properly installed. Improper c0nnecti0n Of the electrical Wiring may create an electric Shock Orfire hazard I
and may result in damage t0the dishwasheris electrical sYsteml
READ AND SAVE THESE INSTRUCTIONS
_mCD_ 1

General Safety Precautions
To reduce the risk of fire, electric shock, serious injury or death when using your appliance, follow basic safety
precautions, including the following:
WARNING
, D0 notinstall or operate this dishwasher if it has
been damaged; dropped; has damaged e!ectrical
c0nd uitor wires 0ri s notworking p[oper!y. If the
product is damaged when received, immediate!y :
contact the dea!er or builder i
Use this dishwasher only foi its intended purpose
as outlined in the use and care manual. It is not
, Keep all packaging materials away fromch!ldren
Plastic bags can cause suffocatic
_ To aVoid e!ectric sh0ckl thiS dishwasher mUst be
installed and grounded bya qualified instal!er in
a completely enclosed cabinet according tOthese
installation instructionsl
AI! installati0n W0[kl plUmbing connections and
electrical wiring must be performed in accordance
wi!b allapplicable codes and standard s
• Install Or locate this appliance 0nly in accordance
with these installation instructions.
' The installer mUst show the cust0mer the location
of the fuse box or Circuit breaker pane! s0 that the
customer knows where and how to turn the power
off.
installing or servicing the dishwasher, switch
p0wer off at the fuse box or circuit breaker panel
and lock the electrical panel door to prevent power
from being switched On accidentallyl When the CirCUt
breaker panel cann0 t be 10cked;securely fasten
a prominent warning device, such as a tag, tothe
' Do n0t leave children alone or unattended in
area where the d shwasher is in use. Never allow
children to sit or stand on an appliance Do not let
children play with this appliance.
, Never allow anyone, including children, to sit or
stand on any part of the dishwasher; Stepping or
sitting on any part of it may result in tipping, damage
and serious injuryl
' Many surfaces Within the dishwasher achieve high
temperatures. Do not touch interior surfaces or items
inside the dishwasher during or immediately after
use. Exercise caution when opening the door. Let
hot air and steam escape before looking or reaching
WARNING
•Do not operate the dishwasher without the door
..................... the toe kick panel in place.
• Store all detergents and rinse aids out of the reach
of children.
• During loading, insert all sharp or pointed objects
with the handles up. Locate these items where they
will not damage the door seal or cause personal
injury.
• Do not taroper with the controls.
• Under certain conditions hydrogen gas may be
produced in a hot water system that has not been
used for two weeks or more. Hydrogen gas is
explosive. If the hot water system has not been used
for a period of time, turn on all hot water faucets and
let the water flow for several minutes to release any
accumulated hydrogen gas. Do not smoke or use an
open flame during this process.
• To prevent child entrapment, always remove the
door from an old dishwasher when removing it from
service.
• To prevent household mold and mildew damage,
periodically check the inlet and drain hoses for leaks.
• If the dishwasher outlet is connected to a garbage
disposal, make sure the disposal is completely empty
before running the dishwasher.
• To avoid damage to the racks, ao not let sharp edges
come into contact with them.
• This appliance is designed for installation by more
than one person. To avoid personal injury, do not
attempt to move or lift the dishwasher without
assistance.
To prevent personal injury and damage to the unit
due to it tipping over, do not push down on the door
anytime it is open. To reduce the chance of tipping,
attach the anti-tip brackets to the cabinet before
operation.
The customer should not install, repair or replace
any part of the dishwasher unless specifically
recommended in the literature accompanying it.
A qualified service technician should perform all
other service. Contact the nearest Dacor authorized
service representative for examination, repair or
adjustment.
2_mC_

Product
Technical
Specifications
Water Pressure 20 to 120 psi (138 - 827 kPa)
120 °F, minimum
15 Amp. 120 Vac, 60 Hz dedicated, grounded, circuit.
Water Temperature
Electrical Circuit
Requirements
Total Connected
Load 12 Amp. @ 120 Vac, 60 Hz.*
* For reference only. For exact specifications see the product data label
located inside the left door jamb.
Dimensions
• 23 7/8" (60.6cm) ,
Door style varies with model number.
Tolerances: +1/16",-0, (+1.6 mm,-0)
unless otherwise stated
ED24:
29 5/8" (75.2 cm)
ID24:
26 7/8" (68.3 cm)
--IDoor.J ,nlowered'/pOsitiOn L L --__'__ . I ?!", ./ i
._" _ 20"(50.8cm)
Adjustablebekick I" 23 3/4"(60.3cm)
47"(119.4cm)
33 3/4"
(85.7 cm)
to
36 1/4"
(92.1 cm)
B
*Allows for hose on back of unit
I_mCD_ 3

WARNING I IMPORTANT: Follow all cabinet and countertop minimum
dimensions shown below to insure safe operation.
observe all governing codes and ordinances during I Prepare the installation location as shown below. All
planning and insta!lati0nl contact your 10calbuilding I minimum product dimensions be must met or exceeded
department for further information. (see page 3). Dimensions shown provide minimum
Preparing the Location
Carefully check the location where the dishwasher is to be
installed. Put it in a location with convenient access. Make
certain that electrical power can be provided in the selected
location.
clearances, unless otherwise noted.
The floor must be solid, level and all cut-out surfaces must
be at right angles. The dishwasher must be secured to the
adjacent cabinets using the anti-tip brackets for safety and
proper operation.
Plan the installation so that the appliance can be removed
if service is required.
./
24"(61.0cm)
Fasten anti-tip anchors into material
under counter top and adjacent cablinets
/
/
/\
90° 90 o
Access hole for utilities
0.3 cm × 12.7 c
24" (61.0 cm)
33 3/4"
(85.7 cm)
to
36 1/4"
(92.1 cm)
1
CUT-OUT FRONT VIEW
Min. countertop 25" (63.5 cm) V
L-DL J
CABINET INSTALLATION SIDE VIEW
4_mC_

Power Supply Preparation
WARNING
The e!ectdcal power Supply for the dishwasher :must be
installed only by a licensed electrician as specified bel0w.
It is the owner!s responsibility to ensure that the electrical
connection of this appliance is performed bYa licensed
electrician:
Electrical Specifications
The electrical installation, including minimum supply
wire size and grounding, must be Jnaccordance with the
National Electric code ANSI/NFPA* (or latest revision) and
local codes and ordinances.
*A copy of this standard may be obtained from:
National Fire Protection Association
1 Batterymarch Park
Quincy, Massachusetts 02269-9101
Power supply requirements:
The dishwasher requires a grounded, dedicated
120 Vac, 60 Hz circuit protected by a 15 Amp. circuit
breaker or time delay fuse installed by a licensed
electrician.
• It must be located to the right or left of the cut-out, in an
adjacent cabinet, so that power can be disconnected
without removing the dishwasher.
The ground terminal (or lead) on the appliance must be
connected to a grounded, metallic, permanent wiring
system or grounding conductor installed by a licensed
electrician.
• Do not ground the appliance or appliance wiring to a
gas pipeline or to the neutral (white) power supply wire.
• Do not install a fuse in the neutral or ground circuit.
The dishwasher can be connected to:
A UL/CSA approved, grounded, three-prong receptacle (if
local code permits). This method is the easiest to install.
OR
Directly to the house wiring. Hard-wire the dishwasher
according to local code directly to a three wire grounded,
single phase connection in a junction box.
NOTE: In either case, be sure the power cable or wire is
long enough to remain connected when the appliance is
removed from the cut-out for service.
If the electrical service does not meet the
specifications above:
• Have a licensed electrician prepare the electrical
receptacle or junction box for final connection inside the
adjacent cabinet according to the specifications above.
Plumbing Preparation
The water pressure must be between 20 and 120 psi
(138-827 kPa). The household hot water heater must
supply a minimum of 120 °F water to the dishwasher
location for best results.
Install a valve for the hot water supply line where it is
easily accessible after the dishwasher is installed.
A flexible braided hot water inlet hose is highly
recommended for connection to the hot water supply.
Connect it to the unit just prior to installation into the
cabinet. The dishwasher ships with a 3/8" (10 mm) male
compression fitting on the hot water inlet to facilitate
installation.
Drain line44"
(1118 mm)long
from chassis
strap
I1II IIII
Back of
dishwasher drain hose,
U or change
Chassis strap 5 1/2" Hot water inlet
(do not remove) (140 mm)(_
Preparing the Drain
CAUTION
Keep the factorY installed high loop drain hose in
place to ensure proper dishwasher operation; D0 not
Cut, tie, strap or lower iL If it is necessary to lengthen
it, install an aftermarket drain extension kit, available
at most home improvement stores.
IMPORTANT: A drain hose is supplied with the product
(see above). Should a longer drain hose be required, use a
hose approved for detergents and high temperature water.
The drain hose supplied with the dishwasher meets an
AHAM DW-1 test standard. Longer drain hoses should not
be longer than a total of 12 ft. in length.
• You must install an air gap in the drain if the drain hose
is connected to household plumbing lower than 20 in.
(50.8 cm) from the floor or if required by local codes.
Plan for the air gap in the sink or countertop area
adjacent to the dishwasher. A section of drain hose (not
provided) needs to be installed from the air gap to the
disposal or waste tee.
If an air gap is not required, the drain hose must be
installed to an inlet or waste tee above the drain trap in
the household plumbing.
The drain hose supplied with the dishwasher should be
connected to a minimum 1/2 in. I.D. drain connection.
_mCD_ 5

Verify the Package Contents
NOTE: Model ID24 ships without a front panel. It is
designed for the installation of an integrated front panel that
matches the surrounding cabinets.
D
D
B
B
0
With the assistance of at least one person, remove the
dishwasher from the shipping carton. Place the unit to
the side of the cabinet opening.
Remove all of the packing materials from inside and
outside of the unit. DO NOT allow any of the shipping
materials, loose screws or plastic to remain inside.
Remove the racks. Set them aside for later installation.
Unpack the parts box and verify that all required
components have been provided. If any item is missing
or damaged, please contact the dealer immediately. Do
not install a damaged or incomplete appliance.
Extended toe kick
Left side access panel
6 Plastic fasteners (for access panel)
Use and care manual
Model ID24 only: Integrated template, screws and
door tensioning springs for heavy door panels.
A bottle of Dacor _ Stainless Steel Cleaner is also
included with models having stainless steel doors.
Tools required for installation:
Wire strippers
Level
0
m
D
nun
0
Crescent wrench
Phillips screwdriver
Tape measure
Materials required for installation
(not provided):
O2 wire nuts to fit wire mentioned above. Additional
wire nuts may be required for connection to house
wiring.
D 3/4" UL/CSA approved strain relief
OHose clamp (for 1 3/8" OD drain hose)
E_ 3/8" flexible braided fill hose (required length varies)
][_] Wire or three-prong UL/CSA approved electric cord
(see electrical specifications)
I!
!1
Make sure you have everything necessary for proper
installation before proceeding.
13 24-Inch
Integ rated
Custom
Panel
Installation
urn
Ii
6_mC_

Electrical Connection 5.
WARNING
•Do not install the dishwasher unless the electrical
service provided meets the dishwasher specifications
(see page 5).
o To avoid an electrical shock hazard, turn off power
to the electrical outlet or junction box at the circuit
breaker panel or fuse box before proceeding. Do not
turn on the power or water supply until instructed to do
so on the following pages.
To prevent the possibility of a short circuit if using
metal conduit for the electrical connection, route it on
the ground under the bottom of the dishwasher as
instructed below.
1. Make sure power to the electrical receptacle or house
junction box is off.
2. Before connecting the wiring and the plumbing, push
the dishwasher into position with the back of the unit
about six (6) inches in front of the cut-out.
,Remove the two (2) screws that hold the toe kick
assembly in place and remove it. NOTE: Do not
reinstall the toe kick until the dishwasher is completely
installed and tested.
,
Remove the dishwasher junction box cover screw and
remove the cover. The junction box is mounted to the
dishwasher chassis below the door.
_--" Screw
Junction Box Location
Install a 3/4" UL/CSA approved strain relief on the base
of the dishwasher junction box.
Wire
Strain j
relief nuts
/
Door
kick
Retaining screw,
2 places assembly
,Route the electrical wiring through the back of the unit 7.
to the back of the dishwasher electrical junction box.
IMPORTANT: If using metal conduit, prevent a short
circuit condition by routing it on the ground under the 8.
unit and bringing the end up behind the junction box as
shown below. Doing so reduces the chance of shorts
against the internal motor and heater terminals. 9.
base
plate
Motor assembly
inside unit
Conduit
10.
11.
0
Ground
connection
Junction Box Wiring
Strip the three (3) wires on the end of the electric cord
or one end of the wire that will connect to the house
wiring.
Feed the end of the wire or cord through the
dishwasher chassis into the junction box base through
the strain relief.
Loosen the grounding screw on the base and connect
the green wire. Tighten it into place.
Connect the power cord (or house wiring) black
and white wires to the black and white wires inside
the junction box. Match the colors. Use wire nuts to
connect them.
Tighten the strain relief. Pull gently on the wiring from
the back to make sure it is secure.
12. Replace the junction box cover and screw.
_mCD_ 7

Electrical Connection
(Continued)
13. Feed the electric wire or cord into the utility hole in
the side of the cut-out. Pull all of the slack out of the wire.
If the unit is to be connected directly to the house
wiring:
•With power turned off at the circuit breaker or fuse
box, remove the house junction box cover.
• Feed the dishwasher wiring into the junction box.
Secure the wire with a UL/CSA approved strain relief.
• Strip and connect the wires according to one of the
wiring diagrams below.
• Tighten the strain relief. Check to make sure the wire
is secure.
• Replace the junction box cover and screws.
WARNING
• Connect the dishwasher ground wire to a separate,
properly grounded wire installed by a licensed
electrician.
• A grounded cold water pipe must have metal continuity
to an electrical ground and must not be interrupted by
insulating materials. Any insulating materials must be
jumped with a length of No. 4 copper wire securely
clamped to bare metal at both ends. See diagram
below.
Wire nut,
3 place,,_
To house circuit breaker
panel or fuse box
Strain relief
To dishwasher \
Junction box
Standard 3-Wire Connection
to House Junction Box*
Junction box
GREEN
GREEN
,t
Strain relief
To dishwasher _
Utility cut-outs
/\
Wire or
Hoses cord
/
Feed the electric cord (or wire) and both hoses into the
utility cutout(s); direction varies with installation.
To house circuit breaker
panel or fuse box
/
L
_D
Separate No. 10 (minimum)
copper ground wire
,/
3-Wire Connection
with External Ground*
* Does not apply when using a 3-prong power cord.
"Wire nut,
3 places
No. 4
copper wire
Meter
Clamps
Bare metal
Insulated Pipe Jumper
(if necessary)
8i:_=lcl_r,