Dacor EDWH24S Technical manual

PLANNING
GUIDE
www.Dacor.com Phone: [phone]
Specications subject to change without notice.
Install all appliances according to accompanying installation instructions. 10.3
EDWH24S, IDWH24
24” Wide Built-In Dishwasher
A
B
Front
Drain hose
C
D Handle depth
2” (50.0 cm)
5 1/4” (13.5 cm) to
7 1/4” (18.5 cm)
Depth with door closed
Depth dimensions allow
for hose on back of unit
49 3/4” (126.4 cm)
Depth with door open
Side
3 1/4" (8.3 cm) 2 3/4" (7.0 cm)
54" (137 cm) long
Drain hose
44" (112 cm) long
Power cord
Back
60" (152 cm)
Water supply line
long
Do not modify
loop in hose
Product Dimensions
Model EDWH24S Model IDWH24
Front Panel Type Stainless steel Integrated
front panel2
(A) Width 24” (61.0 cm) 23 5/8” (60.0 cm)
(B) Height 34 3/8” (87.4 cm) to
36 1/2” (92.7 cm)
34 1/8” (86.7 cm) to
36 1/8” (91.8 cm)3
(C) Depth 24” (61.0 cm) 22 7/8” (58.1 cm)4
(D) Handle Depth1Epicure®: 2 1/2” (6.4 cm)
Millennia®: 2” (5.1 cm) NA
1Epicure handle kit PN: ADWE24H
Millennia handle kit PN: ADWM24H
2Model IDWH24 requires installation of customer provided, custom overlay
door panel. It blends the exterior of the dishwasher into the overall kitchen
décor. Customer must also supply custom or standard appliance handle for
the front of the panel. See page 2/3 for more information.
3Height with required trim kit installed.
4Without custom front panel installed.
Product tolerances: ±1/16” (±1.6 mm)
otherwise stated
Document # PG10-005 Revised 07/16/10 Page 1/3
WARNING
Observe all governing codes and ordinances during planning•
and installation. Contact your local building department for
further information.
This appliance must be installed in accordance with the•
accompanying installation instructions.
UTILITY CONNECTION DIMENSIONS
Approximate
Shipping Weight
108 lbs. (49 kg.).
Electrical Specifications
Dedicated Circuit Required Total
Connected Load
Grounded, 3-prong, electrical outlet
supplied by120 Vac,
60 Hz, 15 Amp. (circuit breaker)
11 Amp. @ 120 Vac, 60 Hz.
The above specifications are for reference only. For exact■
specifications see the product data label, located inside the right door
jamb.
Do not use an extension cord.■
Water Supply Specifications
Water Pressure:■4.2 to 125 p.s.i. (30-862 kPa) with minimum water
flow of 3 gallons (12 liters) per minute.
Water Supply Temperature:■Cold or hot water supply (maximum
140°F, 60°C) may be used. If a cold water supply is used, the washing
times will be longer but performance will not be affected.
Water Supply Valve Requirement:■3/8” water supply valve for
connection to dishwasher’s water supply line is required in a location
where it is easily accessible after the dishwasher is installed. The
dishwasher water supply line is equipped with a 3/8” (10 mm) NPT
female compression fitting on the end.

PLANNING
GUIDE
www.Dacor.com Phone: [phone]
Specications subject to change without notice.
Install all appliances according to accompanying installation instructions. 10.4
EDWH24S, IDWH24
24” Wide Built-In Dishwasher
24” (61.0 cm)
23 5/8”
(60.0 cm)
Power cord/water
supply access hole(s)
1 ½” x 1 ½” Max.
(3.8 cm x 3.8 cm)
Drain line access
hole 2” x 2”
(5.1 cm x 5.1 cm)
E
F
DISHWASHER CUTOUT - FRONT VIEW
CUSTOM PANEL
DIMENSIONS
Cutout tolerances: +1/16”, -0, (+1.6 mm, -0)
Document # PG10-005 Revised 07/16/10 Page 2/3
Location Specifications
Install in a location with convenient access, close to the kitchen sink■
for easy water supply and drain connection. All minimum product
dimensions must be met or exceeded. Dimensions shown on this
page provide the required clearances.
The cabinet must enclose the dishwasher on top, back and sides.■
Plan the installation so that the appliance can be removed easily■
if service is required. The electrical outlet, water supply valve and
drain connection must be installed to the right or left of the cutout
and accessible
when dishwasher is
installed.
If dishwasher is■
installed in a corner,
there must be a
minimum clearance
of 2” (5.1 cm) from
the side wall so the
door can open. See
diagram.
Floor must be■
solid and level. All
cutout surfaces
must be at right
angles. Surrounding
cabinet must have
sufficient material
for attachment of the
anti-tip brackets (see
installation instructions).
The opening (E) through the partition between the drain connection■
and the dishwasher cutout must be higher than the disposer or
waste tee connection (see page 3/3) and lower than 30” (76 cm). If
the partition is wood, the edges of the opening shall be smooth and
rounded. If the partition is metal, the edges of the opening shall be
covered with an edge protector.
Custom Panel/Handle for Model IDWH24
The custom panel mounting screws are provided with the dishwasher.■
Follow the panel dimensions below to ensure that the custom overlay
panel and the accompanying fasteners will fit properly.
Dacor does not advise the use of a knob or handle utilizing a■
single fastener. Instead use a handle with a larger D-style pull.
Any handle designed for use with an appliance should produce
satisfactory results. Handle mounting hardware is not provided with
the dishwasher. The panel craftsman must determine and obtain the
proper handle fasteners for the application. The handle screw heads
must be countersunk into the panel before panel installation.
(G) Height (H) Width (J) Thickness
30 1/8” (76.5 cm) 23 3/4” (60.3 cm) 3/4” (1.9 cm) Min.
IMPORTANT: If the door panel weighs more than 15 pounds, you must
order the optional heavy duty door springs (Dacor PN 701385). Maximum
panel weight with heavy duty springs: 23 pounds.
2” (5.1 cm) Min.
clearance
G
H
J
Model (F) Cutout Height
EDWH24S 34 1/2” (87.6 cm) to 36 1/2” (92.7 cm)
IDWH24* 34 1/8” (86.7 cm) to 36 1/8” (91.8 cm)
*Model IDWH24 requires installation of a trim kit (Dacor PN 701386)
to fill the space between the edge of the cutout and the dishwasher.

PLANNING
GUIDE
www.Dacor.com Phone: [phone]
Specications subject to change without notice.
Install all appliances according to accompanying installation instructions. 10.5
EDWH24S, IDWH24
24” Wide Built-In Dishwasher
Document # PG10-005 Revised 07/16/10 Page 3/3
EXAMPLE OF DRAIN CONNECTION WITHOUT AIR GAP
EXAMPLE OF DRAIN CONNECTION WITH AIR GAP
Drain Specifications
The drain connection must be a minimum of 20 inches (50.8 cm)■
above the floor. No part of the drain hose can be higher than 37 1/2”
(95.0 cm) from the bottom of the dishwasher.
Should a drain hose longer than the one provided be required, use a■
hose extension approved for detergents and high temperature water.
Total drain hose length (including any extensions) must not exceed■
14 ft. 9 in. (450 cm) in length from the top of the drain loop on the
back of the unit. Joints and joint tubes must have a minimum inside
diameter of 5/8” (1.6 cm).
The drain hose supplied with the dishwasher must be connected■
to a minimum 1/2" inside diameter drain connection. A clamp is not
supplied. The drain hose is equipped with a connector that fits drain
connections with an internal diameter of 1/2 to 7/8 inches (1.3 to
2.2 cm).
Install an air gap in the drain system if required by local codes.■
Plan the air gap location on the countertop area adjacent to the
dishwasher. A section of drain hose (not provided) needs to be
installed from the air gap to the drain connection.
If an air gap is not required, the drain hose must be installed to a■
disposer inlet or waste tee above the drain trap in the household
plumbing.
20"
Min.
20"
Min.