Dacor Epicure ER36D Technical manual

PLANNING
GUIDE
www.Dacor.com Phone: [phone]
Specications subject to change without notice.
Install all appliances according to accompanying installation instructions. 5.10
Epicure®Ranges
ER36D, ER48D
GAS - ELECTRICAL ACCESS DIMENSIONS
Model A B C D E*
ER36D 5 5/8”
(142.9 mm)
18 3/8”
(466.7 mm)
10 3/4”
(273.0 mm)
13 11/16”
(347.7 mm)
7/8”
(22.2 mm)
ER48D 3 13/16”
(96.8 mm)
18 11/16”
(474.7 mm)
9 3/8”
(238.1 mm)
13 3/4”
(349.3 mm)
1 1/8”
(28.6 mm)
* The diameter on models equipped for use in Canada is ¼” (6.4mm) larger than
those stated. Canadian units come from the factory pre-wired with an appliance
cord. When installing an appliance cord on models that are not pre-wired, the hole
size must be increased to 1 1/8” (1 3/8” for model ER48D) by removing the conduit
bracket inside the range electrical access box.
48” (1219 mm) Front of open door
Front of handle
Front edge of bull nose
Front panel
Rear of front panel/oven door
30 3/4” (781 mm)
(483 mm)
(908 mm)
(940 mm)
(76 mm)
24” (610 mm)
(51 mm)
(387 mm)
(40 mm)
(229 mm)
(229 mm)
29 3/8” (746 mm)
28 1/4” (718 mm)
26 1/8” (664 mm)
**
**
**
** Optional
1 1/16” (27 mm) to cooking
surface (top of grates) from
top of trim
Finished side
panel
Width: ER36D - 35 7/8” (911 mm)
ER48D - 47 7/8” (1216 mm)
B
A
C
D
Gas regulator access,
cover removed
Range electrical access,
cover removed
E Electrical connection
hole in bottom
Inlet
Back of range
Product tolerances: +/- 1/16” (+/- 1.6 mm) unless otherwise stated
GAS SUPPLY PRESSURE REQUIREMENTS*
Gas Type Manifold Pressure Minimum Gas Supply
Pressure
Natural Gas 5” Water Column 6” Water Column
Propane (LP) 10” Water Column 11” Water Column
* Maximum gas supply pressure 1/2 p.s.i. for all models
WARNING
Observe all governing codes and ordinances during planning•
and installation. Contact your local building department for
further information.
This appliance must be installed in accordance with the•
accompanying installation instructions.
ELECTRIC CIRCUIT REQUIREMENTS
Range Model Circuit Required Total Connected Load
ER36D
240 Vac, 4-wire* 60 Hz, 30
Amp. (Min.) 40 Amp. (Recom-
mended)
6.5 kW (28 Amp.)
ER48D 240 Vac, 4-wire* 60 Hz, 50
Amp. 10.0 kW (42 Amp.)
* 4-wire, two 120 Vac hot (L1 and L2), one neutral, one ground
Document # PG05 - 004 Revised 02/04/10 Page 1/2

PLANNING
GUIDE
www.Dacor.com Phone: [phone]
Specications subject to change without notice.
Install all appliances according to accompanying installation instructions. 5.11
Epicure®Ranges
ER36D, ER48D
CUT-OUT DIMENSIONS
Range Model F G H
ER36D 42” (1067 mm)*
36” (914 mm)**
36 1/16”
(916 mm)**
33 1/2”
(848 mm)
ER48D 54” (1372 mm)*
48” (1219 mm)**
48 1/16”
(1221 mm)**
43 1/2”
(1102 mm)
* Recommended
**Minimum
Gas and Electrical Service
For replacement purposes, the location of the existing utilities may■
be utilized provided they do not interfere with the sides or rear of the
range. Check local building codes for permissible locations.
An external manual shut-off valve must be installed between the gas■
inlet and the range, for the purpose of turning on or shutting off gas to
the appliance.
The installation must allow for the following:
Access to the gas shut-off valve when the unit is installed.■
Access to the remote circuit breaker panel/fuse box, when the range■
is in place.
The gas supply piping and shut-off valve, and the electrical junction■
box/receptacle must be located so they do not interfere with the range
when it is installed.
The junction box and gas shut off valve must be located so that■
the range can be pulled out for service while the appliance remains
connected.
Note 2
F
G
2
Cabinet/countertop depth is at discretion of customer but
cabinet face MUST NOT protrude further than rear of front
panel, see product dimensions.
3
Consult local code for exact location requirements.
1
Vertical to combustible surface from range grate level; if
installing an overhead vent hood, also check the hood
specifications for minimum required clearances.
Non-combustible
surface along
back wall
recommended
10” (254 mm) Min.
to combustible side
walls above the range
(both sides)
30” (762 mm)
Min.
1
36 1/2”
(927 mm)
Max.
13” (330 mm)
Max.
4
18” (457 mm)
Min.
1, 4
Suggested
location of
utilities
3
4
Not applicable for cabinets more than a horizontal
distance of 10” (254 mm) from the edge of the range.
G
10" (254 mm) Min.
to combustible side
walls above the range
(both sides)
non-combustible
Minumum Countertop Height:
30 1/4” (768 mm)
Maximum Countertop Height:
36 1/2” (927 mm)
rear wall recommended
Backsplash
3/8" (10 mm)
Min. flat countertop
overhang
H
2 13/16"
(71.4 mm)
3
CUTOUT WITH OPTIONAL ERV RAISED VENT
(TOP VIEW)
APPROVED RAISED VENT MODELS
Raised Vent Model For Use With
Range Model
ERV36-ER ER36D
ERV48-ER ER48D
Stiffener Cabinet face**
Countertop*
* IMPORTANT: See “CUTOUT WITH OPTIONAL ERV RAISED VENT”
for countertop cutout dimensions.
** IMPORTANT: Cabinet face must not stick out further than
back of control panel.
Back of
control
panel
ERV36-ER or
ERV48-ER
raised vent
ER36D or ER48D Range
3/8” Min. (10 mm)
space behind
raised vent
chassis to clear
stiffener
3/8” Min. (10 mm)
flat countertop overhang
required behind cutout
Countertop height:
30 1/4" (768 mm) Min.
36 1/2” (927 mm) Max.
RAISED VENT INSTALLATION SIDE VIEW
Cutout tolerances: +1/16” (+1.6 mm), -0 unless otherwise stated
Document # PG05 - 004 Revised 02/04/10 Page 2/2