Dacor Epicure EGR30 User manual

Installation Instructions
Epicure TM Ranges
SAVE AND READ THESE INSTRUCTIONS
TESTED IN ACCORDANCE WITH THE LATEST EDITION OF ANSI Z21.1 STANDARD FOR HOUSEHOLD GAS
COOKING APPLIANCES.
CONVENTIONS USED IN THESE INSTRUCTIONS
WARNINGS:
Must be followed carefully to avoid personal injury or damage.
NOTES:
Contain helpful hints and tips to facilitate the installation.
IMPORTANT
1. Before beginning installation, please thoroughly read and become familiar with these instructions.
2. Installation and service must be completed by a qualified installer or service agency.
3. Installer: Please leave these Installation Instructions with the owner.
4. Owner: Please keep these instructions for local electrical inspector's use and for future reference.
5. Read the accompanying Use & Care Manual prior to operating this appliance.
TABLE OF CONTENTS
STEP 1 Verifying package contents
STEP 2 Gas supply requirements
STEP 3 Electrical power supply requirements
STEP 4 Gas and electrical rough-in locations
STEP 5 Cabinet and countertop preparation
STEP 6 Overall dimensions
STEP 7 Installing the anti-tip bracket
STEP 8 Gas regulator and electrical conduit location
STEP 9 Removal and installation of backguards
STEP 10 Removing the oven door
STEP 11 Electrical connection
STEP 12 Gas connection
STEP 13 Installing the range
STEP 14 Installing the burner components
STEP 15 Re-installing the oven door
STEP 16 Verifying proper operation
Part No. 65089 Rev. G
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
2
2
2
2
3-4
5
5
6
6
7
7-8
8
8
8
8
9

IMPORTANT SAFETY INSTRUCTIONS
WARNINGS:
1. Read all instructions before
using the appliance.
.If the information in this
manual is not followed exactly,
a fire or explosion may result
causing property damage,
personal injury, or death.
.
.
.
Improper installation,
adjustment, alteration, 9.
service, or maintenance can
cause personal injury or
property damage. Refer to
these instructions and the 10.
accompanying Use & Care
Manual. For assistance or
additional information, consult
a qualified installer, service
agency, manufacturer (dealer),
or the gas supplier. 11.
4. What to do ifyou smell gas:
•Do not try to light any
appliance. 12.
•Do not touch any electrical
switch, do not use any phone
in your building.
•Immediately call the gas
supplier from a neighbor's
phone.
•Follow the gas supplier's
instructions. 13.
•If you cannot reach your
gas supplier, call the fire
department.
5. For your safety:
•Do not store or use gasoline
or other flammable vapors and
liquids in the vicinity of this or
any other appliance.
•Do not obstruct the flow of
combustion and ventilation air
to the unit.
•Keep appliance area clear and
free from combustible material.
•Do not use or attempt to use
this appliance in the event of a
power failure.
.This unit is designed as a
cooking appliance. Never use
it for warming or heating a
room.
14.
15.
16.
This appliance must not
be used in combination
with surface (countertop)
ventilation systems. The
use of an overhead hood is
recommended for ventilation.
This appliance must be
installed with the gas pressure
regulator supplied with it.
Disconnect the electrical
supply before installing or
servicing the appliance.
This appliance must be
grounded. Connect only to a
properly grounded electrical
supply. Refer to "Electrical
Requirements".
Install or locate this appliance
only in accordance with these
installation instructions.
Use this appliance only for
its intended use as described
in this manual. Do not use
corrosive chemicals or vapors
in this appliance. This type of
appliance is not designed for
industrial or laboratory use.
As with any appliance, close
supervision is necessary
when used by children.
Do not operate this appliance
if it has a damaged electrical
cord, plug, conduit or wires,
if it is not working properly,
or if it has been damaged or
dropped.
Installation of this appliance
must be performed by a
qualified installer, service
agency or the gas supplier.
This appliance should be
serviced only by qualified
service personnel. Contact the
nearest DACOR Authorized
Servicer at [phone],
or at www.dacor.com for
examination, repair or
adjustment.
@NOTES:
1. Some products, such as whole
eggs, and sealed containers,
such as closed glass jars, may
explode and should not be
heated on this cooktop.
I_aCD_

Verifying the Package Contents
Verify that all required components have been
provided. If any item is missing or damaged,
please contact your dealer immediately. Do not
install a damaged or incomplete appliance.
Use & Care Manual
Ignitor Cleaning Kit
Broiler Pan/Grill
Anti-tip Bracket (selected models)
Grate/Burner Cap Packs
Griddle
Burner Rings
Wok Ring
Simmerptate
Spatula
Stainless Steel Cleaner
Pry Stick
Gas Supply Requirements
Check your local building codes for the proper
method dinstallation. In the absence of local
codes, this appliance should be installed in
accordance with the National Fuel Gas Code
ANSI Z223.1. Be certain that the appliance
being installed is correct for the gas service
being provided. Refer to the data plate located
behind the inlet air cooling grill, and/or the table
to the right, for gas supply requirements. Open
the oven door and remove the inlet air cooling
grill for access to the data plate.
[_ WARNING:
This appliance must be installed
by a licensed plumber or gas
fitter when installed within the
Commonwealth of Massachusetts.
Electrical Power Supply
Requirements
It is the owner's responsibility to ensure that 2.
the electrical connection of this appliance
is performed by a qualified electrician. The
electrical installation, including minimum supply
wire size and grounding, must be in accordance
with the National Electric code ANSItNFPA 70-
1993" (or latest revision) and local codes and
ordinances. 3,
*A copy of this standard may be obtained from:
National Fire Protection Association
1 Batterymarch Park
Quincy, Massachusetts 02269-9101
The correct voltage, frequency, and amperage
must be supplied to the appliance from a
separate, grounded, circuit that is protected by a
properly sized circuit breaker or time delay fuse.
Refer to the data plate, and/or the table to the
right, for gas supply requirements.
[_ WARNING:
If the gas or electric service
provided does not meet the
product specifications, do not
proceed with the installation.
Call the selling dealer, the gas
supplier, or a licensed electrician.
Dacor
Model No.
EGR30
EGR30LP
ERD30
ERD30LP
ERD36
ERD36LP
ERDE36
ERDE36LP
ERD48
ERD48LP
ERDE48
ERDE48LP
ERD60
ERD60LP
Electrical
Circuit
Required
120VAC, 60Hz,
15A
120/240VAC,
60Hz, 30A
120/240VAC,
60Hz, 40A
120/240VAC,
60Hz, 50A
120VAC, 60Hz,
3OA
Total
Connected
Load
0.75kW
(6A)
4.2kW
(22A)
4.7kW
(24A)
7.7kW
(34A)
10.0kW
(46A)
10.8kW\
(48A)
4.1kW
(21A)
Gas
Type
Natural
Liquid
Propane
Natural
Liquid
Propane
Natural
Liquid
Propane
Natural
Liquid
Propane
Natural
Liquid
Propane
Natural
Liquid
Propane
Natural
Liquid
Propane
Manifold
Pressure
5" Water Column
10" Water Column
5" Water Column
10" Water Column
5" Water Column
10" Water Column
5" Water Column
10" Water Column
5" Water Column
10" Water Column
5" Water Column
10" Water Column
5" Water Column
10" Water Column
Min. Gas Supply
Pressure
6" Water Column
11" Water Column
6" Water Column
11" Water Column
6" Water Column
11" Water Column
6" Water Column
11" Water Column
6" Water Column
11" Water Column
6" Water Column
11" Water Column
6" Water Column
11" Water Column
Gas and Electrical Supply Requirements
1.
NOTES:
The power supply must
be properly polarized.
Reverse polarity will result in
continuous sparking of the
electrodes, even after flame
ignition.
If there is any doubt as to
whether the power supply
is properly polarized or
grounded, have it checked by
a qualified electrician.
Two electrical circuits and gas
supplies are required for the
ERD60.
Gas and Electrical Rough-In
Locations
NOTE:
The shaded areas shown in the
illustrations, denote the location
of the gas stub and the electrical
junction box/receptacle. These
are suggested locations. For
replacement purposes, the
location of the existing utilities
may be utilized provided that they
do not interfere with the sides or
rear of the range. If installing the
gas valve behind the range, verify
that local building codes will
permit this.
A manual shut valve must be installed in the
gas piping, external to the appliance, for the
purpose of turning on or shutting off gas to the
appliance. Plan the location of the range and the
gas supply to allow access to the valve when
the unit is installed. Access to the remote circuit
breaker panel/fuse box, with the range in place,
must also be allowed for in the installation. Any
openings in the wall behind the appliance and in
the floor under the appliance must be sealed.
Both the gas supply piping and shut-off valve,
and the electrical junction box/receptacle
must be located so they do not interfere with
the range when it is installed. In addition, the
junction box must be located so the range
can be removed for service when the conduit
supplied with the unit is attached to the junction
box. Do not lengthen the conduit or wiring
provided with the range.
All dimensions shown are based on standard
American cabinets 36 inches (914mm) high
at the finished countertop by 24 inches
(610mm) deep, with a 25 inch (635mm) overall
countertop depth. When installing the range
into nonstandard cabinets, minimum clearances
shown in the diagrams on page 3 must be
maintained.
Carefully check the location where the range is
to be installed. For best performance, the range
should be placed away from drafts that may be
caused by doors, windows and HVAC outlets.
i::_a='Qr 2

Cabinet and Countertop Preparation
@NOTES:
1. If cabinet storage space is to
be provided directly above
the range, the risk of personal
injury may be reduced by
installing a ventilating hood
that projects horizontally a
minimum of 5 inches beyond
the face of the cabinets.
2. The range may be installed
flush to the rear wall. We
recommend installing a non-
combustible material on the
rear wall above the range
and up to the vent hood. It
is not necessary to install
non-combustible materials
behind the range below the
countertop height.
3. The minimum distance from
the sides of the range above
the countertop to combustible
side walls must be at least 10
inches.
NOTE:
On 36" and 48" models, install
either the 3", 9" or 24" Backguard
on the Range prior to installing
the Range into the cabinet cutout.
NOTE:
Utilities may be located: In the
lower left corner of the adjacent
right cabinet. (Recommended)
IMPORTANT:
Contact your local building
department to verify compliance with
local code interpretation.
(330ram)
Maximum
Hood
18" (457mm)
Minumim
25"
(635mm)
ERD36 &ERD48
Top of
finished
counter
Model Number
ERD30
EGR30
ERD36
ERDE36
ERD48
ERDE48
ERD60
36" (914mm)
Recommended
30" (762mm) Minimum
42" (1067mm)
Recommended
36" (9!4mm) Minimum
54" (1372mm)
Recommended
48" (!219mm) Minimum
66" (1676mm)
Recommended
60" (1542mm) Minimum
30 1/16" (764mm)
36 1/16" (203mm)
48 1/8" (1222mm)
60 1/8" (1572mm)
Cutout Dimensions
10" (254mm) Min
to combustible side
walls above the range
(both sides)
3=::_=lcar:

t3/32"
(1Omm)
23 3/10"
(5_i9mm)
_ 13/16" (21ram)
29 1/4" (743mm)
ear wall . -
, i.,' I
Vertical
non-combustible i
surface I
30 1/16" (764mm)
3/4" (19mm)
Max backsplash •"" - - "" -
r I _\\
1/4" (dmmi," I ,1
Min flat led g_... L , ."
Rear wall \ _ _ - _
i !'\surface '
, \
i Vertical
i non-combustible
i 20 /16"
I i (513mm)
i_ 3[] 1/10" (764mm) _
/ /
I
13/32"
(10ram)
ERD/EGR3O Slide-in, Self-Rimming installation with Side
Panels and Backguard Removed
Top View
ERDtEGR30 Slide-In, Self-Rimming Installation using 3"
Side Panels (Model No. AESPO3),
Baekguard Removed.
Top View
Vertical
non-combustible Backsplash
surface rear wall \. I................. 27 7/8" (7OSmm) ...................I_ ~ thicker than
_k z
i . I ,I . t i 3/4"(19mm) _---.
/ H/
27t3/16" ! _ ! -- ,, _m/ /
(706ram) i _ /1/4" (6mm) "_ A I /
, I Min. flat ledge • _ 1 ,.
i Adjust for baeksplash i
II .... 3/4"dgck /
; _I "_' :21m- ;3/nI_ )t° 3 13/16"
13/32" (10mm) _ 29 1/4" (743mm) ........................
30 1/16" (764mm) _ I_,_. 6" (152mm) Min
Countertop overhangs cabinet to combustible side
walls above the range
(both sides)
ERV3O with ERD3O Slide-In, Self-Rimming Installation using 3" Side Panels
(Model No. AESPO3), Backguard Removed.
Top View
Vertical
non-combustible
surface rear wall
27 13/16"
(706ram)
27 7/8" (708mm) _. _
, , / _ ' _ L _ 3/4" (19mm)
_- _ Max backsplash _"_-'_
/2 13/16'I
1/4. = ,'
M'nflat'edge\.Lh: I
_ 13/16" 6"
13/32" (1Omm) _ .......................29 1/4" (743mm) ........................._"
30 t/16" (764mrn) _ (152mm) Min.
Countertop overhangs cabinet to combustible side
walls above the range
(both sides)
ERV30 with ERD3O Slide-in, Self-Rimming Installation with Side Panels and Backguard Removed
Top View
_r 4

Overall Dimensions
@NOTE:
For ERD all front-to-back depth
dimensions are reduced by 1"
(25mm) when Backguard and full
side panels are removed.
@NOTE:
For Backguard Installation (36"
and 48" models) see page 6.
Always install backguard before
installation of the range.
1 9/f 8'r_
(4Omm) I
30 3/8" (772mm)_
29 1/8" (740mm)
28 1/8" (714mm) _
28 1/2" (673mm)
9ram)
19.& £_ __
(483mm) 45 1/4"
(387mm)
1-
Finished Side
Panel
Handle
Front Edge of Bullnose
Face of Control Panel/Oven Door
Rear of Control Panel/Oven Door
3" 24"(610mm)
(79ram) Backguard
37"
(940ram)
to
35 3/4"
(908ram)
ERD36, ERDE36, ERD48 & ERDE48 Overall Dimensions
Side View
1 9/16" _ _.
(4Omm) _]
i
28 I/2" (724mm)
27" (686mm)
26" (860mm)
24 3/8" (619mm)
\
When Backguard and
Side Panels are
removed, the overall
depth decreases
by 1" (25ram)
Finished Side Pane[
Handle
Front Edge of Butlnose
Face of Control Panel/Oven Door
Rear of Control Panel/Oven Door
6" (I52mm) Backguard
372
(940ram)
to
35 3/4"
(908ram)
Accessory 3" (76ram) Side Panels
(Dacor ModeJ No. AESP03)
ERD/EGR3O, ERD6O Overall Dimensions
Side View
Installing the Anti-Tip Bracket (30"
& 36" Models Only)
[_ WARNING:
The 30" and 36" ranges require an
anti-tip device. Before installing
the range, you must locate and
secure the anti-tip bracket to the
floor.
8 3/8"
(213mm) /_
2 3/16" /" "\,
_/"/ ill: 2"(3 mm)
(' 5'ram) Floor
i A[[ Dimensions are
_L_/AlroDmicabinet Only
ij_ 30 1/t6" 1 (Not Countertop)
(7644mm)
installation of ERD3O Anti-Tip Bracket
Top View
7 1/2" i/'T"\,
Back'waN (191rnm) f' fv_f _,
_ _ '_ _ r_
\ i I // I 4 318"(,//22mm)
,o :/
i ! i
24" (810ram
_ ' 18 1/32" i All Dimensions are
_r_Dicaebinet Onlyi ii
_ ((458m
36 1/t6" [ (Not Countertop)
(916mm)
Installation of ERD36 Anti-Tip Bracket
Top View
/
Rear
Leveler
5/16 - 18 x 2
or Equivalent
Location of ERD30 Anti-Tip Leveler
Left
Leg
/
Rear
LeveJer
5/16-18 x2
or Equivalent
Location of ERD36 Anti-Tip Leveler
Left
Leg
5c_acor

Gas Regulator and Electrical
Conduit Location
Factory installed j
3/4" regulator #LJ
{1/2,, supply ek_
Power cord /
Gas Regulator and Electrical Conduit Location
Rear View
Installing the 36" and 48" Range
Backguards
Your DACOR range was equipped with
a shipping cover to protect the internal
components prior to installation.
This cover must be removed and replaced by
a DACOR backguard for your range to function
properly,
[_ WARNING:
Be sure that the unit is not
connected to gas or power before
proceeding.
1. Unpack the contents of the box and verify
parts with the Packing List.
2. Remove the single screw on the top of the
shipping cover.
3. Slide the shipping cover off the unit.
ERe with 9" Flue Extension
(9" flue extension shown)
5.
6.
ERD48 with 9" Flue Extension
(9" flue extension shown)
Remove the backguard from its box.
To avoid scratches, place small scraps
of thin cardboard on the rear of the
side panels where the backguard will
make contact. With the assistance of at
least one other person, carefully lift the
backguard over the exhaust flues and
place down on to the range top. Special
attention should be given to the lower
flange in front of the backguard, which
m_ must fit between the stainless steel side
panels.
7. Fasten the provided screws through the
rear flange.
Re I
Shipping Cover
Backguard _
Shipping Cover
Shipping Cover Removal
(36" range shown)
4. Locate and install the flue exhaust
extensions at the rear of the range (9" and
24" backguards only). Use the provided
hex screws and tighten securely into the
pre-drilled holes.
(9"and 24"only)
ERD Baekguard Installation
ERD48 Baekguard Installation
NOTE:
For 24" Backguards, fasten the
provided screws through the
holes in the back panel of the
Backguard.
8. Connect the gas line to the regulator.
Reposition and attach the access panel or
the back cover if the entire back cover was
removed.
9. You are now ready to continue with the
range installation,
I:_a_'r_rt 6

Removing the Oven Door
[_ WARNINGS:
1. Do not attempt to disengage
the hinge catches with the door
removed from the oven. The
hinge springs could release
causing personal injury.
2. Do not lift or carry the oven
door by the door handle.
Open the door to its fully opened position.
Rotate the catch over the retaining arm on each
hinge. Lift the oven door to about a 30 degree
angle from the horizontal position. Pull the door
away from the oven while continuing to lift.
Electrical Connection
[_ WARNINGS:
1. ERD models must be
connected to a grounded,
metallic, permanent wiring
system. Alternatively, a
grounding conductor should
be connected to the grounding
terminal or lead on the
appliance.
2. ERG models must be
connected to a grounded
receptacle. Failure to do so
may result in an electrical
shock hazard.
3. Do not use an extension cord
with this appliance. Such use
may result in fire, electrical
shock, or other personal
injury.
4. Do not install a fuse in the
neutral or ground circuit. A
fuse in the neutral or ground
circuit may result in an
electrical shock hazard.
Grounding Instructions (ERD Models Only)
This appliance must be electrically
grounded, With the range positioned directly in
front of the cabinet cutout, feed the appliance
conduit to the electrical junction box. Then,
depending upon local codes, utilize one of the
following techniques to connect the appliance to
the electrical power supply:
A. Connecting to a Four-Wire Electrical
System
1. Separate the green and white appliance
wires.
2. Connect the white appliance wire to the
neutral (white) supply wire in the junction
box.
3. Connect the black appliance wire to the
black (L1) power supply wire in the junction
box.
4. Connect the red appliance wire to the red
(L2) power supply wire in the junction box.
To remove doqr
rotate catch up.
Lift door up to 30 ° angle,
then pull door away
_:_30 o from the section.
range oven
Removing the Oven Door
Connect the green appliance wire to the
green house grounding wire in the junction
box. Cable from
power supply
_Ju_ction
RED WHITE
RED WHITE
Conduit from
appliance
Connecting the appliance to a
four-wire power supply
Wire nut
(4 places)
[_[} WARNING:
**Do not connect the green
appliance wire to the neutral
(white) supply wire unless local
building codes permit.
Cable from
power supply
RED GREEN
RED
Conduit from
appliance
/Junction
box
Wire nut
(3 places)
**Connecting the appliance to a
three-wire power supply
Electrical Connection - ERD Model
Ranges Only
B. Connecting the Green Appliance Wire to
the Neutral (White) Supply Wire - Where
Local Codes Permit
1. Connect the green and white appliance
wires to the neutral (white) supply wire in
the junction box.
2. Connect the black appliance wire to the
black (L!) power supply wire in the junction
box.
3. Connect the red appliance wire to the red
(L2) power supply wire in the junction box.
C. Connecting the Green Appliance Wire to
a Grounded Supply Wire or a Grounded
Cold Water Pipe - Where Local Codes
Permit.
1. Separate the green and white appliance
wires.
2. Connect the white appliance wire to the
neutral (white) supply wire in the junction
box.
3. Connect the black appliance wire to the
black (L1) power supply wire in the junction
box.
4. Connect the red appliance wire to the red
(L2) power supply wire in the junction box.
5. Connect the green appliance wire to a
grounded supply wire in the junction box or
to a grounded cold water pipe.
6. If connecting to a grounded cold water
pipe, a separate copper grounding wire
(No. 10 minimum) must be connected to a
grounded cold water pipe by means of a
clamp and then to an external grounding
connector screw.
_[} WARNINGS:
1. Do not ground the appliance
to a gas supply pipe or hot
water pipe.
2. Do not turn on power to the
appliance until the range is
permanently grounded.
7_aca_

Cable from
power supply _Separate No. 10 (minimum)
__Ji uncti°nGREEREDRED BLACKWHITEWHITE" box(4Wireplaces)nut copper__v groundingwir_iwaterMetal __ml_l_pipe cop pe_/No 4 ata_
Conduit from
appliance
Connecting the appliance ground to a grounded junction box wire or grounded cold water pipe
.A grounded cold water pipe
must have metal continuity to
electrical ground and must not
be interrupted by insulating
materials. Any insulating
materials must be jumped
with a length of No. 4 copper
wire securely clamped to bare
metal at both ends.
Gas Connection
Before sliding the range into the cabinet,
connect a flexible gas connector to the gas
shut-off valve previously installed on the stub
out. The gas valve must be turned off during
installation. Connect the flex connector to the
pipe fitting at the right rear of the range.
WARNINGS:
1. Do not apply excessive
pressure when tightening gas
connections and fittings.
2. Do not use teflon tape or
plumber's putty on gas flex
line connections.
3. Turn all cooktop controlvaIves
to the "OFF" position. Turn
on gas supply and check all
lines and connections for
leaks using a soap and water
solution. Do not use a flame to
check for leaks. After verifying
that there are no gas leaks,
turn off the gas supply to
the range by turning the gas
shut-off valve to the "OFF"
position.
4. For LP installations, the LP
gas tank must have its own
high pressure regulator. This
is in addition to the pressure
regulator provided with the
range.
5. The maximum gas supply
pressure to the regulator must
never exceed 1/2 pound per
square inch.
@NOTE:
The gas pressure regulator is
pre-set at the factory for the
type of gas intended for use with
the appliance. Verify that the
appliance is compatible with the
type of gas available by checking
the data plate located behind the
inlet air cooling grill. Open the
oven door and remove the inlet air
cooling grill for access to the data
plate. Ranges intended for use
with LP gases will have "LP" as a
part of the model number. Consult
your dealer if the range is not
compatible with your gas supply.
Installing the Range
Measure from the floor to the countertop and
adjust the leveling legs as required to position
the top frame at the desired height, based on
the cabinet and countertop installation. Carefully
slide the range into position in the cutout. The
rear anti-tip leg should engage the anti-tip
bracket.(30 and 36 inch models only)
When the range is to be installed as a "slide-in,
self rimming" (with the range top overhanging
the countertop cutout - ERD/ERG30 models
only), measure from the floor to the countertop.
Adjust the leveling legs to position the bottom
edge of the range top frame approximately !/8"
above the level of the countertop. This will allow
the range to slide over the countertop. Carefully
slide the range into position in the cutout. The
rear anti-tip leg should engage the anti-tip
bracket. To lower the range onto the countertop,
turn the leveling legs counterclockwise. Lower
the range until the bottom of the range top just
contacts the countertop. Do not allow the full
weight of the range to hang on the counter.
Installing the Burner Components
Remove the brass burner rings, porcelain burner
caps, and porcelain gates from their shipping
packages. Place each burner ring onto its
corresponding burner base, being certain that
the five alignment tabs slide into the matching
notches in the base. Set each porcelain burner
cap on top of its corresponding burner ring.
Place oven exhaust cover over the opening in
the top frame. Place each grate onto the top
frame, being certain that the rubber feet are
positioned in the locating dimples.
[_[} WARNING:
Never attempt to operate the
cooktop section of the range with
any of the burner rings, burner
caps or grates removed.
@NOTE:
Prior to operating the cooktop or
oven sections of the range, please
read the accompanying Use and
Care Manual carefully. Important
safety, service and warranty
information is contained within
this manual.
Re-installing the Oven Door(s)
Grasp the oven door on opposite sides and
lift it until the door hinges are aligned with the
openings in the oven frame. Holding the door at
about a 30° angle from the horizontal, slide the
hinges into the openings until the bottom hinge
arms drop fully into the hinge receptacles. Lower
the door to the fully opened position, and then
rotate the two hinge catches toward the oven.
Open and close the door completely to ensure
that it is properly installed.
Peel off the protective layer of plastic that covers
the door panel.
_aCQ_ 8

Verifying Proper Operation
Before beginning the test procedure, ensure
that all cooktop control valves are in the "OFF"
position, and all burner rings, burner caps, and
grates are properly positioned on the top frame.
Turn on the gas supply at the shut-off valve.
Turn on the power supply to the range. Set the
time of day by pressing the "CLOCK" key and
then pressing either of the "TIME.TEMP" keys
to advance or reduce the time in the display
in the desired setting. Press the "BAKE" key.
Select a temperature of 350°F by pressing the
"TIME.TEMP" "+" key. The display should show
"BAKE ON". Press the "CANCEL.SECURE"
key to stop the oven heating process. Test each
top burner separately by pressing and turning
one control knob at a time counterclockwise
to the "HIGH" position. All ignitors will spark
continuously, but only the burner with gas
flowing to it will ignite. (It will take approximately
4 seconds for ignition to occur, at which
time the ignitors will stop sparking. If ignition
does not occur within 4 seconds, turn off
the knob, wait for at least 2 minutes to allow
any gas to dissipate, then repeat this ignition
test.) The control knob can then be rotated
counterclockwise from "HIGH" to "LOW" to
adjust the flame height progressively. Repeat
the ignition test for all burners. When installed
properly, the flame will be steady and quiet. It
will also have a sharp, blue inner cone that will
vary in length proportional to the burner size.
[_ WARNINGS:
1. The range and shut-off
valve must be disconnected
from the gas supply piping
during any pressure testing
exceeding 1/2 psi (3.5kPa).
2. The range must be isolated
from the gas supply piping
by closing the shut-off valve
during any pressure testing at
or below 1/2 psi (3.5 kPa).
@NOTES:
If either the oven or cooktop does
not operate properly, follow these
troubleshooting steps:
1. Verify that power and gas are
supplied to the range.
2. Check the electrical
connections and gas supply
to ensure that the installation
has been completed correctly.
3. Repeat the above bake test or
burner ignition test.
4. If the appliance still does not
work, contact an authorized
DACOR service company at
[phone]. Do not
attempt to repair the
appliance yourself. DACOR
is not responsible for service
required to correct a faulty
installation.
9_a=D_

_acar I0

Specifications contained within are subject to change without notice.
No liabilty is assumed by DACOR for changes in specifications.
Web Site: www.dacor.com
For a Dealer/Service: [phone]
Corporate Phone: [phone] ®